Machine type
Prestige XL series (L2, XL2, XL2 Pro, XL3, XL4)
DTF Station Prestige R2 Pro
DTF Station Prestige R1
DTF Station Prestige R2 (original)
Prestige X6
DTF Station Prestige A4
DTF Station Prestige A3+ and A3+ R
Epson SureColor G6070 DTF printer
Mimaki TxF300-1600
Mimaki TxF330-800
STS XPD-924D DTF Printer (Mutoh)
STS VJ-628D DTF Printer (Mutoh)
DTF Station Vega S17
STS XpertJet 1682D (XPJ-1682D) 64 inch DTF Printer
STS XPD-724 DTF Printer (Mutoh)
Hotronix Fusion IQ, Air Fusion IQ and Dual Air Fusion IQ
Geo Knight DK20S and DK20SP Digital Knight Swing-Away Presses
DTF Station Maxima and Proxima Dual Heat Presses
Hotronix Auto Open Clam and Hover Heat Press
DTF Station Prisma Auto Heat Press
DTF Station Prisma Dual Heat Press
DTF Station Prisma Swing Heat Press
Insta 718, 728 and 828 Automatic Swing-Away Heat Presses
DTF Station Prisma Sentry Heat Press
Geo Knight DC16 and DC16AP Digital Combo Swing-Away Presses
Geo Knight DK Digital Clamshell Presses: DK20, DK16, DKA Auto, DK8 Label and DK7 Cap
Hotronix Auto Open Cap Press and 360 IQ Hat Press
Hotronix Craft Heat Press 9 x 12
Hotronix Mighty Mug Heat Press
Insta 256 and 288 Manual Swing-Away Heat Presses
Insta 907 Dual Station Shuttle Label Heat Press
Viper MAXX pretreatment machine
Ecofreen Mister-T2 and Mister-T2 Pro pretreatment machines
Pearl Elite and Pearl PTM DTG pretreatment machines
Viper XPT-1000 pretreatment machine
Lawson Silver-Jet and Silver-Jet V2 DTG Pretreat Sprayers
Lawson Zoom-AE DTG pretreatment machine
Viper MINI handheld DTG pretreatment machine
Brand
Prestige XL series (L2, XL2, XL2 Pro, XL3, XL4)
DTF Station Prestige R2 Pro
DTF Station Prestige R1
DTF Station Prestige R2 (original)
Prestige X6
DTF Station Prestige A4
DTF Station Prestige A3+ and A3+ R
DTF Station Aries 124 UV DTF printer
Miro DTF Powder Shakers: Miro 13 Max, 16, 24 and 36
DTF Station Aries 213 and Aries 113 UV DTF printers
Seismo L16R and L24R DTF Powder Shaker and Dryer
Phoenix Air 16x20 DTF Curing Oven
DTF Station Maxima and Proxima Dual Heat Presses
DTF Station Prisma Auto Heat Press
DTF Station Prisma Dual Heat Press
DTF Station Prisma Swing Heat Press
DTF Station Vega S17
DTF Station Prisma Sentry Heat Press
DTF Station Seismo V36R DTF Powder Shaker and Dryer
DTF Station Arc 127 automatic cutter for DTF and UV DTF film
Epson SureColor F2100
Epson SureColor G6070 DTF printer
Epson SureColor F2270
Epson SureColor F3070
Epson SureColor F570
Epson SureColor F170
Epson SureColor F6470 and F6470H
Epson SureColor F6370
Epson SureColor F7200
Epson SureColor P-Series photo printers (P700, P900, P6570, P8570)
Epson SureColor T-Series CAD and technical printers
Epson SureColor S-Series (S40600, S60600, S80600)
Prisma Swing setup: mounting the control box, aviation plugs, support feet and power
Take the control box out of the foam, fix it to the machine arm with its 4 screws, then connect the 5-pin and 2-pin aviation plugs. Bolt the support feet onto the base so the press can't tip when the head swings away, and strap the power cord to the 5-pin plug so it can't touch the heat platen. Plug into a grounded outlet on a full 20 amp circuit.
The Prisma Swing ships with its control box packed separately. Setup takes about fifteen minutes and needs no special tools beyond a screwdriver. Do it with the press unplugged.
Assemble the press
-
Mount the control box
Take the control box out of its packing foam and set it on the machine arm. Fix it in place with the 4 screws supplied.
-
Connect the 5-pin aviation plug
Plug the round 5-pin connector into its socket on the control box. Push it fully home and secure it so it can't work loose.
-
Connect the 2-pin aviation plug
Plug the smaller 2-pin connector into its socket the same way. Both plugs must be fully seated or the press can lose heat or power when the head moves.
-
Fit the support feet
Fix the support feet onto the machine base. They stop the press from tipping over when the heat platen swings to the side.
-
Strap the power cord
Bind the power cord to the 5-pin plug with the hook-and-loop strap. This keeps the cord away from the heat platen while you work.
Never run the press without the support feet. A swung-out 16 x 20 heat platen is heavy enough to pull the press off the bench.
Power it safely
- Plug into a properly grounded outlet on a full 20 amp circuit at 120 V. The press draws 16.4 A at full heat.
- Don't use a circuit rated under 15 amps, or one shared with another heat press or other high-demand equipment.
- Avoid extension cords. If you must use one, keep it short and no lighter than 12 gauge.
- If the power cord is damaged, stop using the press. It has to be replaced by the manufacturer, its service agent or a similarly qualified person. Contact us.
On a weak circuit the press may behave strangely, show the wrong temperature, heat slowly or trip the breaker. Fix the circuit before you assume the press is faulty.
First start
-
Switch on
Turn on the red power switch on the control box. The screen shows time, temperature and the press counter.
-
Set temperature and time
Press SET once to set temperature and again to set time. See the settings guide linked below.
-
Let it heat fully
Allow about 20 minutes to reach 350°F. Keep the head swung away or open while it heats, with nothing on the lower platen.
-
Do a test press
Press a scrap garment first and check the transfer before you run real orders.
Next: Prisma Swing temperature, time and pressure. If something doesn't fit or a plug won't seat, text us a photo at (562) 609-4996.
Common questions
Do I really need the support feet?
Yes. The manual says they stop the press from tipping over when the heat platen swings away. Fit them before the first use.
Can I use an extension cord?
Only if you must. Keep it as short as possible and no lighter than 12 gauge. A heavy-duty cord is best.
What happens on a weak or shared circuit?
The manual lists erratic controller behavior, wrong temperature readings, slow heat-up and a tripped breaker. Don't use a circuit under 15 amps or one shared with another heat press.
The control box arrived separately. Is something wrong?
No. It ships packed in foam and mounts on the arm during setup. It is designed to come off for service.
- Prisma Swing operation manual (AA)
- Prisma Swing operation manual (DTF Station)
- Prisma Swing product specifications
- AA support requests about Prisma Swing setup and power cords, 2024 to 2026











































































