Machine type
Prestige XL series (L2, XL2, XL2 Pro, XL3, XL4)
DTF Station Prestige R2 Pro
DTF Station Prestige R1
DTF Station Prestige R2 (original)
Prestige X6
DTF Station Prestige A4
DTF Station Prestige A3+ and A3+ R
Epson SureColor G6070 DTF printer
Mimaki TxF300-1600
Mimaki TxF330-800
STS XPD-924D DTF Printer (Mutoh)
STS VJ-628D DTF Printer (Mutoh)
DTF Station Vega S17
STS XpertJet 1682D (XPJ-1682D) 64 inch DTF Printer
STS XPD-724 DTF Printer (Mutoh)
Hotronix Fusion IQ, Air Fusion IQ and Dual Air Fusion IQ
Geo Knight DK20S and DK20SP Digital Knight Swing-Away Presses
DTF Station Maxima and Proxima Dual Heat Presses
Hotronix Auto Open Clam and Hover Heat Press
DTF Station Prisma Auto Heat Press
DTF Station Prisma Dual Heat Press
DTF Station Prisma Swing Heat Press
Insta 718, 728 and 828 Automatic Swing-Away Heat Presses
DTF Station Prisma Sentry Heat Press
Geo Knight DC16 and DC16AP Digital Combo Swing-Away Presses
Geo Knight DK Digital Clamshell Presses: DK20, DK16, DKA Auto, DK8 Label and DK7 Cap
Hotronix Auto Open Cap Press and 360 IQ Hat Press
Hotronix Craft Heat Press 9 x 12
Hotronix Mighty Mug Heat Press
Insta 256 and 288 Manual Swing-Away Heat Presses
Insta 907 Dual Station Shuttle Label Heat Press
Viper MAXX pretreatment machine
Ecofreen Mister-T2 and Mister-T2 Pro pretreatment machines
Pearl Elite and Pearl PTM DTG pretreatment machines
Viper XPT-1000 pretreatment machine
Lawson Silver-Jet and Silver-Jet V2 DTG Pretreat Sprayers
Lawson Zoom-AE DTG pretreatment machine
Viper MINI handheld DTG pretreatment machine
Brand
Prestige XL series (L2, XL2, XL2 Pro, XL3, XL4)
DTF Station Prestige R2 Pro
DTF Station Prestige R1
DTF Station Prestige R2 (original)
Prestige X6
DTF Station Prestige A4
DTF Station Prestige A3+ and A3+ R
DTF Station Aries 124 UV DTF printer
Miro DTF Powder Shakers: Miro 13 Max, 16, 24 and 36
DTF Station Aries 213 and Aries 113 UV DTF printers
Seismo L16R and L24R DTF Powder Shaker and Dryer
Phoenix Air 16x20 DTF Curing Oven
DTF Station Maxima and Proxima Dual Heat Presses
DTF Station Prisma Auto Heat Press
DTF Station Prisma Dual Heat Press
DTF Station Prisma Swing Heat Press
DTF Station Vega S17
DTF Station Prisma Sentry Heat Press
DTF Station Seismo V36R DTF Powder Shaker and Dryer
DTF Station Arc 127 automatic cutter for DTF and UV DTF film
Epson SureColor F2100
Epson SureColor G6070 DTF printer
Epson SureColor F2270
Epson SureColor F3070
Epson SureColor F570
Epson SureColor F170
Epson SureColor F6470 and F6470H
Epson SureColor F6370
Epson SureColor F7200
Epson SureColor P-Series photo printers (P700, P900, P6570, P8570)
Epson SureColor T-Series CAD and technical printers
Epson SureColor S-Series (S40600, S60600, S80600)
Prisma Swing settings: temperature, time, pressure knob and how a press cycle works
Press SET once and use the up and down arrows to set the temperature, then press SET again to set the time (0 to 999 seconds). Turn the knob on top of the arm clockwise for more pressure and counterclockwise for less. Close the press once it reaches temperature: the timer starts on its own, counts to zero, sounds an alarm and resets for the next press.
The control box has three buttons: SET (mode select), the down arrow and the up arrow. The screen shows the time on the left, the temperature on the right, the press counter below and a Heating indicator while the element is on.
Set the temperature
-
Enter temperature mode
Press SET once. The Temperature and Setting labels light up together.
-
Choose the target
Press the up or down arrow to set the target temperature. The maximum is 430°F (221°C).
Set the time
-
Enter time mode
Press SET again. The Time label lights up.
-
Choose the dwell
Use the up and down arrows to set the press time, anywhere from 0 to 999 seconds.
To show Fahrenheit or Celsius, or to correct a temperature reading, see Prisma Swing and Sentry calibration and °F/°C.
Set the pressure
The pressure knob is the screw on top of the swing arm. Turn it clockwise to increase pressure and counterclockwise to decrease it. The Swing has no pressure readout, so change it in small steps and check the result.
- Set pressure with the garment on the platen, since a thicker garment raises the pressure at the same knob setting.
- If a transfer lifts at the edges or looks faded in spots, add a little pressure and test again.
- If the handle is very hard to lock, or the garment shows a heavy shiny box, back the knob off.
Run a press cycle
-
Wait for temperature
Let the platen reach the set temperature. A cold press can take about 20 minutes to reach 350°F.
-
Load the garment
Swing the head away, dress the garment over the lower platen and place your transfer. Cover it with a PTFE sheet if the transfer calls for one.
-
Close and lock
Swing the head back over the platen and pull the handle down to lock. The timer starts automatically. If the platen is still below the set temperature, the press finishes heating and then starts counting.
-
Open on the alarm
The timer counts down to zero and sounds an alarm. Open the press and swing the head away. The timer resets itself for the next press.
The heat platen and the metal around it stay hot after you switch off. Swing the head away and let it cool fully before you touch it or cover the press.
For settings by transfer type, see the heat press time and temperature chart. If the press won't reach temperature or the timer behaves oddly, see Prisma Swing or Sentry not heating.
Common questions
What's the highest temperature it reaches?
430°F (221°C).
Why didn't the timer start when I closed the press?
If the platen isn't at the set temperature yet, the press finishes heating first and then starts the countdown. Wait for it to reach temperature before you press.
Does the Swing show pressure?
No. There's no pressure readout, so set it by feel and by checking results. Turn the knob clockwise to increase pressure.
What is the number under Counter?
The press counter. It counts completed press cycles.
What temperature and time should I use?
Follow the transfer or vinyl maker's instructions. Our heat press chart and DTF settings guide are good starting points.
- Prisma Swing operation manual (AA)
- Prisma Swing operation manual (DTF Station)
- Prisma Swing product specifications
- AA support requests about Prisma Swing settings, 2024 to 2026











































































