Support
Machine type
Brand
Sawgrass SG500 and SG1000

Sawgrass Print Utility for SG500 and SG1000: install, printer driver, ink type and USB, Ethernet or Wi-Fi connection

✓ Reviewed by Jason KimUpdated 2 min readFits: SG500 · SG1000
Short answer

SG500 and SG1000 printers print through Sawgrass Print Utility, which has replaced Sawgrass Print Manager, with the MySawgrass design tool replacing CreativeStudio. Download it from Sawgrass, sign in with a my.sawgrassink.com account, let it install the printer driver, then choose your ink type. If the printer shows Ready but nothing prints, the usual fixes are selecting the ink type, removing and re-adding the printer, or improving a weak Wi-Fi signal.

What changed: Print Manager and CreativeStudio

Older Sawgrass setups used Sawgrass Print Manager and the CreativeStudio design tool. Sawgrass now uses Sawgrass Print Utility to print and manage the printer, and the MySawgrass design tool for designing. You can also design in CorelDRAW, Canva, Illustrator, Photoshop or Photoshop Elements and send the file to Print Utility. Old CreativeStudio or Print Manager logins don't carry over, so you'll need a new account at my.sawgrassink.com.

Install and add the printer

  1. Check your computer

    Print Utility needs a 64-bit processor, at least 8 GB of RAM (16 GB recommended), 2 GB of free disk space and an internet connection to sign in. It supports Windows 10 and 11 (64-bit) and current macOS versions. Windows on ARM isn't supported.

  2. Download and install

    Download Sawgrass Print Utility for Windows or macOS from sawgrassink.com/products/software and run the installer. You can do this while the printer runs its first ink charge.

  3. Sign in

    Open Print Utility and sign in with your Sawgrass account, or choose Create Account. The same account signs you in to MySawgrass.

  4. Install the printer driver

    Print Utility should walk you through adding the printer. If it doesn't, open Settings, go to Devices (shown as Printers in some versions), choose Add, pick your printer series and model, and click Install Driver. If you're using USB, plug the cable in only when the installer tells you to.

  5. Choose your ink type

    In Settings > Devices, set the ink type to match your cartridges (for example SubliJet-UHD or VersiFlex). The print settings won't appear until you do.

Choose how the printer connects

Connection What to know
USB USB 2.0 only. Printer off, cable into the port under the cover on the left side, then switch on when the driver install asks.
Ethernet CAT5e or CAT6 cable to your router or switch. On the printer set Menu > System Settings > Interface Settings > Network > LAN Type to Ethernet.
Wi-Fi NA and EU models only, 2.4 GHz network, same network as the computer. Set LAN Type to Wireless LAN first.

Connecting to Wi-Fi

After setting the LAN type, go to Menu > System Settings > Interface Settings > Wireless LAN > Wireless LAN Easy Setup. Either choose Push Button Method, press Start and then press WPS on your router, or choose SSID Auto Search, pick your network and type the password. The blue Wi-Fi light stays solid when it's connected. Check the signal under Wireless LAN > Wireless LAN Signal; Sawgrass recommends 75% or higher.

Printer says Ready but nothing prints

  • Print Utility isn't open. It must be running (look for its icon in the taskbar) for jobs from MySawgrass or Quick Print Folders to appear.
  • Pop-ups are blocked. MySawgrass sends designs to Print Utility through a browser pop-up. Allow pop-ups for MySawgrass once and the browser remembers.
  • The printer's address changed. This happens after a router restart, a new IP address, or unplugging USB. Quit Print Utility, remove the printer in your computer's printer settings, then add it again from Print Utility and re-select the ink type.
  • Weak Wi-Fi. Below 75% the connection can drop. Move the printer closer to the router or switch to Ethernet or USB.
  • USB shows offline (Windows). Sawgrass suggests restarting the Print Spooler service, then reinstalling USB Printing Support in Device Manager. On a Mac, remove and re-add the printer, then reset the printing system if needed.

Stuck jobs in the queue can also block printing. If you can't get it sorted, text us a photo of the screen at (562) 609-4996.

Watch Sawgrass's introduction to Sawgrass Print Utility

More videos

Sawgrass: how to allow pop-ups in MySawgrass

Embedded from the manufacturer's official channel.

Common questions

Can I sign in with my old CreativeStudio or Print Manager login?

No. Sawgrass says those accounts don't work in Sawgrass Print Utility or the MySawgrass design tool. Create a new account at my.sawgrassink.com.

Does the printer work with 5 GHz Wi-Fi?

No. It needs a 2.4 GHz network, and Sawgrass recommends a signal of 75% or higher. EUX models have no Wi-Fi at all; use USB or Ethernet.

Can I print straight from Photoshop or Illustrator with the normal printer driver?

Sawgrass warns that printing through the plain driver instead of Sawgrass Print Utility can cause wrong colors, lower quality or banding. Send your files through Print Utility.

Does Print Utility run on any computer?

It needs a 64-bit Windows 10 or 11 PC or a supported macOS version, at least 8 GB of RAM, and internet to sign in. Windows on ARM (Snapdragon and similar) isn't supported. Check Sawgrass's system requirements page for the current list.

The print button says Ink Type Required to Print. What do I do?

Choose the ink type on the print job page, or in Settings > Devices. Print settings stay hidden until the ink type is set.

Did this fix it?