Support
Machine type
Brand
Sawgrass SG500 and SG1000

Sawgrass SG500 and SG1000 error messages, paper jam codes and SC service codes explained

✓ Reviewed by Jason KimUpdated 3 min readFits: SG500 · SG1000
Short answer

Most SG500 and SG1000 jams clear with the Form Feed key after you remove the paper, and repeat jams usually come from paper dust on the feed belt or registration sensor. An SC code means a service error: switch the printer off and on, and if it returns, look up the number. SC 57000 and 57001 usually mean a dirty paper feed belt, and color-specific ink codes usually clear by reseating that cartridge.

Display messages

Message What to do
Low Ink That cartridge is at about 10% or less. Have a new one ready. Don't head clean until it's replaced.
Replace Ink Crtg Open the right front cover and replace the cartridge shown.
Set the Ink correctly / Reset Cartridge Push the cartridge fully in. If it persists, take it out and reinstall it once.
Prepare new Waste Collection Unit The waste unit is nearly full. Order one; you can keep printing for now.
Waste Collection Unit is full Replace the waste collection unit behind the right front cover.
Cover open Close the cover named. For the top cover, make sure nothing is sitting on it.
Temperature out of range Turn off, let the room and printer settle, then turn on. Sawgrass recommends 59 to 77°F.
Head-cleaning or Head-flushing failed Press Exit to clear the error, then run it again.
Maintenance failed Press OK to clear it, then run the maintenance again.
Paper size/type mismatch Make the paper size in Sawgrass Print Utility match the paper in the tray.
Firmware Update Failed Unplug the data cable, power the printer off, restart the computer, then power on and reconnect.

Paper misfeeds and jam codes

  1. Clear the paper

    Follow the message on the display. Pull out the tray named, or open the rear cover with the two gray tabs, and remove the sheet. For a jam under the top cover, press Form Feed, then pull the sheet out slowly at an angle, never straight up. Don't touch the feed belt, ink tubes or toothed belt. Close everything and press Form Feed.

  2. Check the basics

    Make sure the rear cover is fully latched, and that no jobs are left in the print queue. Fan the paper to remove static, flatten any curl, and don't overfill the tray.

  3. Match the jam code

    Code Meaning Sawgrass's fix
    001 Paper slipped, or tray not seated Reload and fan the paper, reseat the tray, clean the feed belt and rollers
    005 Paper longer than the size selected Match the paper size in Print Utility to the paper loaded
    006 Slip in the bypass tray Reload the bypass tray, remove and reinsert it, clean the feed belt and registration sensor
    009 No paper detected Clean the feed belt and the registration sensor
    014, 016, 017 Carriage jam or leftover paper Look for paper scraps, then clean the feed belt, rollers and sensor

Sawgrass's cleaning steps for the feed belt and registration sensor are in our SG500 and SG1000 routine maintenance guide. Some papers shed more dust than others, so if jams keep coming back, try a different paper.

SC (service code) errors

For any SC code, first switch the printer off, then on again. If it returns, find the number below.

Code What it points to What you can do
52000, 57000, 57001 Dirty paper feed belt, or condensation Clean the feed belt. If the printer was moved from somewhere cold, run System Settings > Maintenance > De-condensation.
20211 to 20254, 28111 to 28114, 28211 to 28213 An ink cartridge or channel (the last digit is the color or head) Remove that cartridge, power off, gently shake it, power on and reinsert. Replace it if it feels empty.
93200 Overheating Clear space around the vent, move it away from heat and sun, and leave it off for at least an hour.
93300 Severe fault Contact us.

Sawgrass's fixes for other codes (such as 20000, 21000, 28000 and 29500) involve holding down the lid sensor, moving the print head by hand or working on parts inside the printer. Please text us a photo of the error at (562) 609-4996 and we'll walk you through it.

Watch Sawgrass's video: fixing paper misfeeds on the SG500 and SG1000

More videos

Sawgrass: how to fix Jam Code 001
Sawgrass: how to fix Jam Code 009
Sawgrass: how to fix Jam Codes 014, 016 and 017
Sawgrass: how to fix Jam Code 005

Embedded from the manufacturer's official channel.

Common questions

Where do I see the jam code?

It shows near the top right of the display when a misfeed happens, for example 09.

I cleared the jam but it won't print.

Press the Form Feed selection key after removing the paper. Also check that the rear cover is fully closed with both gray tabs back in place, and that no old jobs are stuck in the computer's print queue.

What does Independent-supply ink set mean?

The printer thinks a cartridge isn't genuine Sawgrass. Sawgrass printers are designed for Sawgrass ink, and Sawgrass says non-genuine ink can void the warranty. If you are using genuine cartridges, contact us.

The display says R Internal Unit Almost Full. Can I replace it?

No, that internal waste tank is a service part. Contact us and we'll arrange it with Sawgrass. It's different from the waste collection unit behind the right front cover, which you replace yourself.

My printer shows SC 93300.

Sawgrass lists 93300 as a severe error that means the printer must be replaced. Contact us with your serial number.

Did this fix it?