Machine type
Prestige XL series (L2, XL2, XL2 Pro, XL3, XL4)
DTF Station Prestige R2 Pro
DTF Station Prestige R1
DTF Station Prestige R2 (original)
Prestige X6
DTF Station Prestige A4
DTF Station Prestige A3+ and A3+ R
Epson SureColor G6070 DTF printer
Mimaki TxF300-1600
Mimaki TxF330-800
STS XPD-924D DTF Printer (Mutoh)
STS VJ-628D DTF Printer (Mutoh)
DTF Station Vega S17
STS XpertJet 1682D (XPJ-1682D) 64 inch DTF Printer
STS XPD-724 DTF Printer (Mutoh)
Hotronix Fusion IQ, Air Fusion IQ and Dual Air Fusion IQ
Geo Knight DK20S and DK20SP Digital Knight Swing-Away Presses
DTF Station Maxima and Proxima Dual Heat Presses
Hotronix Auto Open Clam and Hover Heat Press
DTF Station Prisma Auto Heat Press
DTF Station Prisma Dual Heat Press
DTF Station Prisma Swing Heat Press
Insta 718, 728 and 828 Automatic Swing-Away Heat Presses
DTF Station Prisma Sentry Heat Press
Geo Knight DC16 and DC16AP Digital Combo Swing-Away Presses
Geo Knight DK Digital Clamshell Presses: DK20, DK16, DKA Auto, DK8 Label and DK7 Cap
Hotronix Auto Open Cap Press and 360 IQ Hat Press
Hotronix Craft Heat Press 9 x 12
Hotronix Mighty Mug Heat Press
Insta 256 and 288 Manual Swing-Away Heat Presses
Insta 907 Dual Station Shuttle Label Heat Press
Viper MAXX pretreatment machine
Ecofreen Mister-T2 and Mister-T2 Pro pretreatment machines
Pearl Elite and Pearl PTM DTG pretreatment machines
Viper XPT-1000 pretreatment machine
Lawson Silver-Jet and Silver-Jet V2 DTG Pretreat Sprayers
Lawson Zoom-AE DTG pretreatment machine
Viper MINI handheld DTG pretreatment machine
Brand
Prestige XL series (L2, XL2, XL2 Pro, XL3, XL4)
DTF Station Prestige R2 Pro
DTF Station Prestige R1
DTF Station Prestige R2 (original)
Prestige X6
DTF Station Prestige A4
DTF Station Prestige A3+ and A3+ R
DTF Station Aries 124 UV DTF printer
Miro DTF Powder Shakers: Miro 13 Max, 16, 24 and 36
DTF Station Aries 213 and Aries 113 UV DTF printers
Seismo L16R and L24R DTF Powder Shaker and Dryer
Phoenix Air 16x20 DTF Curing Oven
DTF Station Maxima and Proxima Dual Heat Presses
DTF Station Prisma Auto Heat Press
DTF Station Prisma Dual Heat Press
DTF Station Prisma Swing Heat Press
DTF Station Vega S17
DTF Station Prisma Sentry Heat Press
DTF Station Seismo V36R DTF Powder Shaker and Dryer
DTF Station Arc 127 automatic cutter for DTF and UV DTF film
Epson SureColor F2100
Epson SureColor G6070 DTF printer
Epson SureColor F2270
Epson SureColor F3070
Epson SureColor F570
Epson SureColor F170
Epson SureColor F6470 and F6470H
Epson SureColor F6370
Epson SureColor F7200
Epson SureColor P-Series photo printers (P700, P900, P6570, P8570)
Epson SureColor T-Series CAD and technical printers
Epson SureColor S-Series (S40600, S60600, S80600)
Sawgrass SG500 and SG1000 routine maintenance: feed belt, registration sensor, waste unit, cartridges and storage
Leave the printer on so it can clean itself about every 10 hours, and print at least once or twice a week. Every few months, clean the paper feed belt with a lint-free cloth and isopropyl alcohol, dust off the paper registration sensor, and run the three adjustments. Replace the waste collection unit and cartridges when the display asks, and store spare cartridges at 59 to 77°F.
The two habits that matter most
- Leave it on. The printer runs a short head cleaning cycle about every 10 hours from standby. Switched off, it can't, and it uses extra ink catching up at the next power-on.
- Print regularly. If you don't print daily, Sawgrass recommends at least 1 to 2 prints a week to keep ink moving.
Every few months
-
Clean the paper feed belt
Paper dust and ink build up on the shiny black belt in the middle of the printer and can cause smears, misfeeds and SC 57000 errors. Turn the printer off and unplug it. Open the top cover, then open the rear door by pushing in its two gray tabs. Wipe the belt gently with a lint-free cloth and isopropyl alcohol (denatured alcohol if that's all you have), with no pressure. To reach the rest of the belt, press down gently on the gray rollers at the back to turn it; don't slide them side to side. Let it dry 15 to 30 minutes, or up to an hour, before powering on.
-
Dust off the registration sensor
With the printer off, remove the small sensor cover between the rollers, lift out the sensor, and clear the dust with a soft brush, compressed air or a puff of breath. No liquids. Put it back and power on. A dusty sensor is a common cause of Jam 009.
-
Check the feed rollers
Look at the rubber feed rollers at the back and inside. Some papers leave a white dust coating that stops them gripping. Sawgrass also suggests blowing paper dust out of the printer with compressed air pointed away from the print head carriage.
-
Run the three adjustments
Under Menu > Printer Features > List/Test Print, run Head Position, Adj. Paper Feed and Registration. With VersiFlex ink, the test patterns print in blue instead of black, which is normal.
When the display asks
Replacing the waste collection unit
When Prepare new Waste Collection Unit appears, order one. When it says full, open the right front cover, wait at least five seconds, press the area marked PUSH and pull the unit out level. Put it in the bag supplied with the new one, slide the new unit in until it clicks, and close the cover. Don't install a unit that's been sitting unused for a long time.
Replacing a cartridge
Clear any paper errors first. Open the right front cover, hold the printer steady, pull out the empty cartridge and push in the new one the right way round. Don't shake cartridges hard. The printer runs a head clean automatically after a cartridge change. A cartridge reported empty still holds a little ink on purpose, to stop air entering the printer.
Storing ink and paper
- Store spare cartridges at 59 to 77°F with humidity above 35%, sealed until you need them.
- Store sublimation paper flat, in its original pack, away from humidity and sun.
Moving the printer
For a short move, power off with the Power key, unplug everything, remove the option tray, and carry it level. If it tilts, ink can leak from the waste unit. For shipping, see the FAQ. After moving from a cold place to a warm one, wait at least an hour before switching on.
Questions about any step? Text us a photo or short video at (562) 609-4996.
Watch Sawgrass's video: cleaning the paper feed belt
More videos
Embedded from the manufacturer's official channel.
Common questions
Can I turn the printer off when I'm away?
Sawgrass recommends leaving it on. If you do switch it off for a long period, turn it on for a few minutes every 20 to 25 days, then print a nozzle check before your next job.
Why do I get small wheel marks on VersiFlex prints?
VersiFlex ink stays tacky, and the spiked exit rollers can mark it, especially in humid rooms. Sawgrass suggests cleaning the feed belt and the exit guide, or running De-condensation with three sheets of plain copy paper to soak up ink on the rollers.
Can I use water or cleaner on the registration sensor?
No. Sawgrass says no liquids or solvents on the sensor. Use a soft brush, compressed air or just blow the dust off.
How do I ship the printer for repair?
Use the original box. Leave the cartridges and the waste collection unit installed, because removing them makes ink leak during transport. Remove the paper, unplug the cord and keep the printer level.
How long do cartridges last once opened?
Use them before the Recommended Use By date, ideally within six months of opening. Old ink can hurt print quality and the printer.
- Sawgrass SG500/SG1000 User Guide (PDF)
- Sawgrass Care: Preventative Maintenance Steps (SG500/1000)
- Sawgrass Care: Optimize Your Sawgrass SG500 and SG1000 Performance
- Sawgrass Care: Cleaning the Paper Feed Belt
- Sawgrass Care: Cleaning the Paper Registration Sensor (SG500/1000)
- Sawgrass Care: Printer Maintenance Using VersiFlex Ink Set










































































