Machine type
Prestige XL series (L2, XL2, XL2 Pro, XL3, XL4)
DTF Station Prestige R2 Pro
DTF Station Prestige R1
DTF Station Prestige R2 (original)
Prestige X6
DTF Station Prestige A4
DTF Station Prestige A3+ and A3+ R
Epson SureColor G6070 DTF printer
Mimaki TxF300-1600
Mimaki TxF330-800
STS XPD-924D DTF Printer (Mutoh)
STS VJ-628D DTF Printer (Mutoh)
DTF Station Vega S17
STS XpertJet 1682D (XPJ-1682D) 64 inch DTF Printer
STS XPD-724 DTF Printer (Mutoh)
Hotronix Fusion IQ, Air Fusion IQ and Dual Air Fusion IQ
Geo Knight DK20S and DK20SP Digital Knight Swing-Away Presses
DTF Station Maxima and Proxima Dual Heat Presses
Hotronix Auto Open Clam and Hover Heat Press
DTF Station Prisma Auto Heat Press
DTF Station Prisma Dual Heat Press
DTF Station Prisma Swing Heat Press
Insta 718, 728 and 828 Automatic Swing-Away Heat Presses
DTF Station Prisma Sentry Heat Press
Geo Knight DC16 and DC16AP Digital Combo Swing-Away Presses
Geo Knight DK Digital Clamshell Presses: DK20, DK16, DKA Auto, DK8 Label and DK7 Cap
Hotronix Auto Open Cap Press and 360 IQ Hat Press
Hotronix Craft Heat Press 9 x 12
Hotronix Mighty Mug Heat Press
Insta 256 and 288 Manual Swing-Away Heat Presses
Insta 907 Dual Station Shuttle Label Heat Press
Viper MAXX pretreatment machine
Ecofreen Mister-T2 and Mister-T2 Pro pretreatment machines
Pearl Elite and Pearl PTM DTG pretreatment machines
Viper XPT-1000 pretreatment machine
Lawson Silver-Jet and Silver-Jet V2 DTG Pretreat Sprayers
Lawson Zoom-AE DTG pretreatment machine
Viper MINI handheld DTG pretreatment machine
Brand
Prestige XL series (L2, XL2, XL2 Pro, XL3, XL4)
DTF Station Prestige R2 Pro
DTF Station Prestige R1
DTF Station Prestige R2 (original)
Prestige X6
DTF Station Prestige A4
DTF Station Prestige A3+ and A3+ R
DTF Station Aries 124 UV DTF printer
Miro DTF Powder Shakers: Miro 13 Max, 16, 24 and 36
DTF Station Aries 213 and Aries 113 UV DTF printers
Seismo L16R and L24R DTF Powder Shaker and Dryer
Phoenix Air 16x20 DTF Curing Oven
DTF Station Maxima and Proxima Dual Heat Presses
DTF Station Prisma Auto Heat Press
DTF Station Prisma Dual Heat Press
DTF Station Prisma Swing Heat Press
DTF Station Vega S17
DTF Station Prisma Sentry Heat Press
DTF Station Seismo V36R DTF Powder Shaker and Dryer
DTF Station Arc 127 automatic cutter for DTF and UV DTF film
Epson SureColor F2100
Epson SureColor G6070 DTF printer
Epson SureColor F2270
Epson SureColor F3070
Epson SureColor F570
Epson SureColor F170
Epson SureColor F6470 and F6470H
Epson SureColor F6370
Epson SureColor F7200
Epson SureColor P-Series photo printers (P700, P900, P6570, P8570)
Epson SureColor T-Series CAD and technical printers
Epson SureColor S-Series (S40600, S60600, S80600)
Sawgrass SG500 and SG1000 banding and missing nozzles: nozzle check, head clean, head flush and adjustments
Print a nozzle check first. If dashes are missing, run a head clean on just the affected head and print a check after each one; if two or three cleans don't fix it, move to head flushes. If the nozzle check is perfect but lines run across every color, run the Paper Feed adjustment. Lines in only some colors on a perfect check usually need a flush, and a slower Print Quality setting in Print Utility can help too.
Match your symptom
| What you see | Likely cause | Go to |
|---|---|---|
| Gaps or missing dashes on the nozzle check | Clogged nozzles | Steps 1 to 3 |
| Perfect nozzle check, lines in one or two colors | Weak channel | Step 3, then step 5 |
| Perfect nozzle check, lines across all colors | Paper feed setting | Step 4 |
| Blurred or doubled lines | Head position | Step 4 |
| Print starts in the wrong place | Registration | Step 4 |
-
Print a nozzle check
Go to Menu > Printer Features > List/Test Print > Nozzle Check Pattern and press Print. You can also print one from Sawgrass Print Utility under Settings > Devices. Look for missing dashes or broken lines. The number above each color is its head: Head 1 is cyan and black, Head 2 is magenta and yellow.
-
Head clean the affected head
Go to Menu > Printer Features > List/Test Print > Head-cleaning, choose Head 1, Head 2 or All Heads, and confirm. The panel also has a one-touch No-Fuss Head Cleaning that cleans all heads. Print a nozzle check after each clean. Sawgrass suggests 2 to 3 cleans before moving on.
-
Head flush if cleans don't clear it
Head-flushing is in the same menu and works the same way, but it's stronger and uses much more ink. Flush only the affected head and print a check after each one. Stop as soon as the pattern is complete.
Never switch the printer off during a clean or flush. If power is lost, switch it back on and start again from a nozzle check. Don't clean or flush when a cartridge shows almost empty.
-
Run the adjustments if the nozzle check is perfect
Lines across every color mean the paper is advancing slightly too far or not far enough. Under List/Test Print, choose Adj. Paper Feed, print the test pattern, and enter the value Sawgrass's pattern points to (the lightest gray square with straight lines on both sides). If black streaks remain, raise the value by one. If white streaks remain, lower it. Do the same for Head Position if lines look doubled, and Registration if the image starts in the wrong place. Sawgrass recommends doing these from the driver where possible, and doing all three every few months.
-
Try a slower print mode
If the nozzle check and Sawgrass's Primary Chart are both clean but lines still show, open the job in Sawgrass Print Utility and change Print Quality to Advanced Photo. If lines remain, try Ultra Fine. Make sure you're printing through Print Utility, not the plain printer driver.
Still missing nozzles?
Sawgrass's next step is cleaning the capping station under the print head. It means moving the print head by hand with the lid sensor held down, so we'd rather walk you through it. Text us a photo of your nozzle check at (562) 609-4996.
Also check the basics Sawgrass lists for poor quality: cartridges past their Use By date, printing on the wrong side of the paper, and a paper type setting that doesn't match what's loaded. For faded or blurry transfers after pressing, see sublimation ghosting and faded colors.
Watch Sawgrass's video: how to perform a head cleaning
More videos
Embedded from the manufacturer's official channel.
Common questions
Which head should I clean?
Head 1 prints cyan and black. Head 2 prints magenta and yellow. Clean only the head with missing nozzles to save ink. Use All Heads only when both are affected.
How many head cleans and flushes is too many?
Sawgrass's current guidance is 2 to 3 head cleans, then up to 5 head flushes, with a nozzle check after each. Its printed User Guide is more cautious and says one flush. Flushes use a lot of ink, so stop as soon as the check is complete. If it still isn't clear, text us before going further.
The black row is blank on my nozzle check. Is it clogged?
If you use VersiFlex ink, no. The black slot holds clear expander, which doesn't show on paper. Sawgrass suggests printing the check on glossy paper and looking at it at an angle, and notes the expander rarely clogs.
Why is my printer cleaning on its own?
That's normal. It runs a short cleaning cycle about every 10 hours from standby, after a cartridge change, and after a long idle period. That's why Sawgrass says to leave it on.
Can I run a head clean when a cartridge is almost empty?
No. Sawgrass says not to clean or flush when a cartridge is almost empty, because the ink can run out partway. Replace it first.
- Sawgrass SG500/SG1000 User Guide (PDF)
- Sawgrass Care: Fix Horizontal Lines or Banding on Sawgrass SG500 and SG1000
- Sawgrass Care: Print a Nozzle Check (SG500/1000)
- Sawgrass Care: Perform a Head Clean (SG500/1000)
- Sawgrass Care: Perform a Head Flush (SG500/1000)
- Sawgrass Care: Preventative Maintenance Steps (SG500/1000)
- Sawgrass Care: Printer Maintenance Using VersiFlex Ink Set
- Sawgrass Care: Paper Feed Adjustment (SG500/1000)










































































