Machine type
Prestige XL series (L2, XL2, XL2 Pro, XL3, XL4)
DTF Station Prestige R2 Pro
DTF Station Prestige R1
DTF Station Prestige R2 (original)
Prestige X6
DTF Station Prestige A4
DTF Station Prestige A3+ and A3+ R
Epson SureColor G6070 DTF printer
Mimaki TxF300-1600
Mimaki TxF330-800
STS XPD-924D DTF Printer (Mutoh)
STS VJ-628D DTF Printer (Mutoh)
DTF Station Vega S17
STS XpertJet 1682D (XPJ-1682D) 64 inch DTF Printer
STS XPD-724 DTF Printer (Mutoh)
Hotronix Fusion IQ, Air Fusion IQ and Dual Air Fusion IQ
Geo Knight DK20S and DK20SP Digital Knight Swing-Away Presses
DTF Station Maxima and Proxima Dual Heat Presses
Hotronix Auto Open Clam and Hover Heat Press
DTF Station Prisma Auto Heat Press
DTF Station Prisma Dual Heat Press
DTF Station Prisma Swing Heat Press
Insta 718, 728 and 828 Automatic Swing-Away Heat Presses
DTF Station Prisma Sentry Heat Press
Geo Knight DC16 and DC16AP Digital Combo Swing-Away Presses
Geo Knight DK Digital Clamshell Presses: DK20, DK16, DKA Auto, DK8 Label and DK7 Cap
Hotronix Auto Open Cap Press and 360 IQ Hat Press
Hotronix Craft Heat Press 9 x 12
Hotronix Mighty Mug Heat Press
Insta 256 and 288 Manual Swing-Away Heat Presses
Insta 907 Dual Station Shuttle Label Heat Press
Viper MAXX pretreatment machine
Ecofreen Mister-T2 and Mister-T2 Pro pretreatment machines
Pearl Elite and Pearl PTM DTG pretreatment machines
Viper XPT-1000 pretreatment machine
Lawson Silver-Jet and Silver-Jet V2 DTG Pretreat Sprayers
Lawson Zoom-AE DTG pretreatment machine
Viper MINI handheld DTG pretreatment machine
Brand
Prestige XL series (L2, XL2, XL2 Pro, XL3, XL4)
DTF Station Prestige R2 Pro
DTF Station Prestige R1
DTF Station Prestige R2 (original)
Prestige X6
DTF Station Prestige A4
DTF Station Prestige A3+ and A3+ R
DTF Station Aries 124 UV DTF printer
Miro DTF Powder Shakers: Miro 13 Max, 16, 24 and 36
DTF Station Aries 213 and Aries 113 UV DTF printers
Seismo L16R and L24R DTF Powder Shaker and Dryer
Phoenix Air 16x20 DTF Curing Oven
DTF Station Maxima and Proxima Dual Heat Presses
DTF Station Prisma Auto Heat Press
DTF Station Prisma Dual Heat Press
DTF Station Prisma Swing Heat Press
DTF Station Vega S17
DTF Station Prisma Sentry Heat Press
DTF Station Seismo V36R DTF Powder Shaker and Dryer
DTF Station Arc 127 automatic cutter for DTF and UV DTF film
Epson SureColor F2100
Epson SureColor G6070 DTF printer
Epson SureColor F2270
Epson SureColor F3070
Epson SureColor F570
Epson SureColor F170
Epson SureColor F6470 and F6470H
Epson SureColor F6370
Epson SureColor F7200
Epson SureColor P-Series photo printers (P700, P900, P6570, P8570)
Epson SureColor T-Series CAD and technical printers
Epson SureColor S-Series (S40600, S60600, S80600)
Sawgrass SG500 and SG1000 setup: unboxing, ink install, first ink charge and first nozzle check
Unbox the printer, remove every piece of tape and the foam block inside, attach any optional trays, load paper, then install the four cartridges (black, cyan, magenta, yellow from the left) and switch on. The printer then runs its initial ink charge; leave it alone until the display says Ready. Don't plug in the USB cable until Sawgrass Print Utility tells you to.
Before you start
- Pick a flat, sturdy spot, level within two degrees, with room around it for air and for opening the trays and covers. The SG1000 weighs about 33 lb, so lift it by the indents at the base of each side.
- Use a wall outlet close to the printer. No extension cords or multi-socket adapters.
- Keep it away from direct sun, heaters, air-conditioning vents, humidifiers and the heat press. Sawgrass recommends 59 to 77°F and 45 to 55% humidity.
- Have Sawgrass Print Utility downloaded so you can install it while the ink charge runs.
Don't switch the printer on, and don't plug in the USB cable, until each step below tells you to.
Set it up in this order
-
Unbox and remove all packing
Take off the protective covering and plastic bag and lift the printer out. Remove every piece of tape on the outside, then open the top cover and remove the tape there and the foam block inside. Sawgrass warns that packing left inside can cause Service Code errors. Keep the box for moving the printer later.
-
Attach optional trays
If you bought an option tray or bypass tray, attach it now with the printer unplugged. Lower the printer straight down onto the option tray, corners aligned. The SG1000 tray also has a clamping plate held by a coin screw. The bypass tray clicks in while you press its side tabs. After adding either tray, you'll need to run the Registration adjustment for it.
-
Load sublimation paper
Pull Tray 1 fully out. Slide the guides to the paper size, then load the paper bright white side down, short edge first, below the limit mark. In the bypass tray the print side goes up. Flatten any curl before loading. Use the tray extension only for paper larger than Letter.
-
Install the four cartridges
Open the right front cover. Unpack the cartridges without touching the ink ports or chip contacts. With the Use By date facing you, push them in from the left: black, cyan, magenta, yellow. Close the cover.
-
Power on and let the ink charge finish
Plug the power cord into the printer and the wall, then press Power. The printer starts its initial ink charge. Sawgrass gives this as roughly 7 to 13 minutes, and you may hear clicking. Don't touch the printer, open covers or unplug it until the display shows Ready and the Power key stays lit.
-
Install the software and connect
Install Sawgrass Print Utility, sign in, and let it install the printer driver. Connect by USB only when the installer asks. For Ethernet or Wi-Fi, set the LAN type on the printer first. Our Sawgrass Print Utility guide covers this step in detail.
-
Print your first nozzle check
Go to Menu > Printer Features > List/Test Print > Nozzle Check Pattern and press Print. Every color block should be complete. Sawgrass notes a head clean may be needed after the first ink charge to get a full pattern. With the VersiFlex ink set, the clear expander channel doesn't show on the pattern, which is expected.
After setup
- Leave the printer on. It runs a short cleaning cycle about every 10 hours from standby.
- On EU and EUX models, Sawgrass recommends turning off the auto power-off: Menu > System Settings > Admin. Tools > Main power off network disc. > Off.
- Use cartridges before their Recommended Use By date, ideally within six months of opening.
- If something doesn't look right, text us a photo or short video at (562) 609-4996.
Watch Sawgrass's video: ink, expiration dates and self-maintenance tips
Embedded from the manufacturer's official channel.
Common questions
Why aren't my ink levels at 100% after setup?
That's normal. The first set of cartridges fills the ink lines and print head during the initial ink charge. The ink isn't lost, it's inside the printer. Every cartridge after that reads 100% when new.
Can I switch from SubliJet-UHD to VersiFlex later?
No. Sawgrass says the ink type you load first stays with the printer for its whole life. Decide before you open the first cartridges.
Why does it matter when I connect the USB cable?
If the USB cable goes in before the software asks for it, the computer may not recognize the printer properly and the software can't talk to it. Wait for the prompt in Sawgrass Print Utility.
Should I turn the printer off at night?
No. Sawgrass recommends leaving it on all the time so it can run its automatic maintenance. If you power it off for a long time, it uses more ink catching up when it comes back on.
I moved the printer in from a cold car. Can I switch it on?
Wait at least an hour. Moving from cold to warm can form condensation inside, and the printer needs time to dry out before power-on.










































































