Support
Machine type
Brand
STS VJ-628D DTF Printer (Mutoh)

STS VJ-628D Long Store: how to store the printer and bring it back with Initial Charge

✓ Reviewed by Jason KimUpdated 1 min readFits: VJ-628D · VJ-628D-C
Short answer

Before storing or moving the VJ-628D, run Long Store from the driver's Maintenance tab, empty the waste ink tank and turn the printer off. To bring it back, run Initial Charge: empty the waste tank, swap in cleaning cartridges when asked, empty the tank again, then shake and insert your ink cartridges. STS recommends Long Store any time you won't print for more than 5 days.

Before you start

  • Have enough STS 220 ml cleaning cartridges for every slot, with their cards.
  • Have a container that can hold 1,500 ml for the waste ink.
  • Plan the time. Both procedures run in stages and you'll need to be there to swap cartridges.

Storing or moving: Long Store

  1. Start Long Store

    Open the driver's Utility > Maintenance tab and click Long Store. MSM opens. Click Start on the Longstore tab and follow the screens, which walk you through the head washing.

  2. Don't restart charging

    When the washing finishes, don't run relaunching or Initial Charge. Leave it washed.

  3. Empty the waste ink tank

    Drain the tank through the waste tube into your container and reset the counter. Never move the printer with waste ink in the tank, even a short way, because splashing can cause damage.

  4. Turn it off

    Press the power button. The blue light goes out. Release the media fixing knob and take the film roll out and store it in its box.

  5. If you're shipping it

    The manual also calls for the head fixing plate, the roller protective sheet and the original packing. Contact us before you pack it so nothing gets missed.

Bringing it back: Initial Charge

  1. Power on and open Initial Charge

    Turn the printer on, then open the driver's Utility > Maintenance tab and click Initial Charge.

  2. Empty the waste tank, then Start

    Empty the tank first, then click Start.

  3. Swap in cleaning cartridges

    If any ink cartridges are in the slots, remove them all. Insert a cleaning cartridge in every slot, arrow up, all the way in. The printer charges cleaning fluid.

  4. Remove the cleaning cartridges

    When charging finishes, take them all out. The printer discharges the cleaning fluid.

  5. Empty the tank again, then Start

    Drain the waste tank again and click Start.

  6. Insert ink

    Shake each ink cartridge lightly 2 or 3 times (and the whites as usual), then insert each one into the slot whose label matches its color, arrow up, all the way in. Ink charging starts once all are in. If ink was stored somewhere cold, let it sit at room temperature at least 3 hours first.

  7. Finish and check

    On the Finish screen click Back. Print a nozzle check before your first job.

If MSM stops responding partway through a charge, don't turn the printer off mid-cycle. Note where it stopped and contact us.

Common questions

How long can I leave it with ink in it?

The STS manual allows only short storage with ink charged, and up to 6 months once the ink has been flushed out. If you'll be away more than 5 days, STS says to flush with Long Store.

I ran Long Store but never emptied the waste tank, and now nothing drains.

Don't force the tube. Contact us with a photo of the tank and tube.

Initial Charge stops at the cleaning cartridge step.

Make sure a cleaning cartridge is in every slot, fully inserted with the arrow up, and that each has its card. If it still won't continue, note the MSM message and contact us.

How often should I run Long Store as maintenance?

STS's best practices suggest every three to four months to maintain the ink system, as well as before any idle period of more than 5 days.

Can I tilt the printer to fit it through a door?

No. The manual says not to tilt it, stand it on its side or turn it upside down, or ink can leak.

Sources
Did this fix it?