Support
Machine type
Brand
STS XPD-724 DTF Printer (Mutoh)

STS XPD-724 Long Store, restart with Initial Charge, and draining the waste ink tank

✓ Reviewed by Jason KimUpdated 2 min readFits: XPD-724
Short answer

Before the XPD-724 sits unused, run Long Store from MSM: it washes the ink out of the head and lines with cleaning cartridges, then you drain the waste ink tank. To bring it back, run Initial Charge, which flushes with cleaning cartridges first and then fills with ink. STS also recommends a Long Store every 2 to 3 months to clear sediment, even if you never stop printing.

When to use which

Situation What to run
Normal production Leave the printer on. STS designed it to circulate ink overnight
Every 2 to 3 months Long Store, then Initial Charge, to flush sediment from the lines
Going away or shutting down for more than about a week Long Store before you leave, Initial Charge when you return
Moving or shipping the printer Long Store, drain the waste tank, then call us about repacking

Run Long Store

  1. Have cleaning cartridges ready

    You need a cleaning cartridge for every slot. Make sure the waste tank has room, or drain it first (see below).

  2. Start it from MSM

    In the driver's Printing Preferences go to Utility > Maintenance > Long Store (MSM opens), or open MSM directly. Click Start on the Longstore tab and follow each screen. It tells you when to remove the ink cartridges and insert the cleaning cartridges.

  3. Stop after the wash

    When the cleaning finishes, do not relaunch and do not run Initial Charge. Drain the waste ink tank, then turn the printer off with the power button.

Bring it back with Initial Charge

  1. Power on and open Initial Charge

    Turn the printer on. In the driver go to Utility > Maintenance > Initial Charge, or open it in MSM.

  2. Empty the waste tank, then click Start

    Initial Charge sends a lot of fluid to the tank, so drain it first.

  3. Flush with cleaning cartridges

    Remove any cartridges that are in the slots and insert cleaning cartridges in all slots, arrow up, pushed all the way in. When charging is done, remove them. The printer discharges the cleaning fluid.

  4. Drain the tank again and load ink

    Empty the waste tank, click Start, and shake each ink cartridge 2 or 3 times lightly (give the white the full daily shake). Insert each one in the slot whose label matches its color, arrow up, all the way in. Ink charging starts once all are in. When the Finish screen shows, click Back.

  5. Check the nozzles

    Print a nozzle check before your first job. A few cleanings after a restart are normal.

Drain the waste ink tank

The tank holds 1,500 ml. When it's full the error light comes on and the buzzer sounds, and MSM's Printer Status > Status Information says so.

  1. Get a big enough container

    Use a container that holds at least 1,500 ml, such as a PET bottle. Wear gloves and eye protection.

  2. Drain

    Pull out the tip of the waste ink tube, put it in the container, and turn the valve so it lines up with the tube to open it. If the flow is blocked, gently suction out the debris with a syringe placed into the waste tube.

  3. Reset the counter

    In MSM click Reset Waste Ink, then Yes. The counter goes back to 0.

Waste ink is industrial waste. Dispose of it under your local rules.

Stuck partway through Long Store or Initial Charge? Don't power off. Text us a photo of the MSM screen at (562) 609-4996.

Watch STS Inks' video: clearing a clogged 628 or 724 waste tank

Embedded from the manufacturer's official channel.

Common questions

How long can the XPD-724 sit with ink in it?

The manual's storage spec says up to one week with ink charged. STS's guidelines say to flush with cleaning solution if you won't print for more than 14 days. To be safe, run Long Store before any break longer than a week.

During Long Store, do I put the ink cartridges back in?

No. Follow the MSM screens: cleaning cartridges go in for the wash. After the wash, the manual says not to relaunch and not to run Initial Charge until you are ready to use the printer again.

Long Store keeps stopping with 'the operation failed'. What do I do?

Check MSM's Status Information for the reason. Common ones are a full waste tank or a cartridge that isn't seated. Clear it, then start again. If it stops a second time, text us a screenshot.

My waste tank drains very slowly or not at all.

The manual says you can gently suction out the blockage with a syringe placed into the waste tube. If that doesn't clear it, text us before you take anything apart.

Do I need to empty the waste tank before moving the printer?

Yes, every time, even for a short move. Ink sloshing in the tank during a move can cause damage.

Sources
Did this fix it?