Support
Machine type
Brand
STS XPD-724 DTF Printer (Mutoh)

STS XPD-724 daily, weekly and monthly maintenance: white shake, capping station, wiper and inside cleaning

✓ Reviewed by Jason KimUpdated 3 min readFits: XPD-724
Short answer

Every day, shake both white cartridges, check the platen and media guards are clean, and print a nozzle check before you start. Clean the capping station seal and spit pad every second day, the cleaning wiper and around the head every week, and the inside of the printer every month. Check the flushing box absorber about every two months, and run Long Store every 2 to 3 months.

Every day, before you print

  1. Shake both white cartridges

    Before waking the printer, take out both white cartridges. Hold each one flat and shake it side to side about 40 times with the slot guide up, then again with it down, then shake it upside down. Wipe any free ink off the cartridge end with a paper towel and put it back in its own slot.

  2. Check the platen and the media sensor strip

    Make sure the heated platen is free of ink and residue, the media guards and the area under them are clean, and the black strip at the front of the platen is clean so the media sensor reads correctly.

  3. Print a nozzle check

    Run Nozzle Check from the driver's Utility tab or from MSM, on film. If you see gaps, run a Short or Normal cleaning and check again until the pattern is clean. If it won't clear, follow our white ink and clogging guide.

Every day, after production

Clean the print head guards and the black plastic ramps at each end of the print head, using the CR Maintenance steps below.

Every second day: capping station seal and spit pad

STS asks you to clean the capping station seal and the spit pad every second day. Use the CR Maintenance position below so you can reach them, and use a fresh dry cleaning stick.

Every week: cleaning wiper and around the head

  1. Move the carriage to the maintenance position

    In the driver's Printing Preferences click Utility > Maintenance > CR Maintenance (MSM opens), click Start, then short press the operation key on the printer. The carriage moves to the maintenance position.

  2. Wipe the cleaning wiper

    Open the front cover. With a dry cleaning stick, wipe the left face of the wiper back and forth, then the right face, then the right side of the wiper base. Also clean the wiper drain path.

  3. Clean around the print head

    Look at the underside of the carriage. Clean dust and ink lumps from the silver metal around the head and the black plastic head guides. Do not touch the print head surface with your fingers or the stick, and don't touch the platen, which can be hot.

  4. Put the carriage back

    Close the front cover and short press the operation key. The carriage returns home.

Use each cleaning stick dry and only once, and finish within about 5 minutes. A stick that dries out while you work, or one wet with water or solution, can damage the head.

Every month: inside cleaning

  1. Power off and let it cool

    Turn the printer off and open the front cover. The heater is very hot right after power off, so touch the platen first and wait if it's hot.

  2. Brush and wipe

    Brush dust off the pressure arms with a soft brush. Wipe the platen, media guide and the silver part of the grid roller with a soft cloth soaked in water and squeezed out tightly. Close the cover.

About every two months: flushing box absorber

The flushing box catches the ink the head spits out. When ink lumps rise above its frame, replace the absorber: run CR Maintenance as above, open the front cover, pull up the absorber's tab to release the hook, lift it out (watch for drips), fit the new one, close the cover and press the operation key.

Every 2 to 3 months: Long Store

STS recommends running Long Store from MSM to flush sediment from the lines. See our Long Store and restart guide.

Whenever the printer asks: waste ink tank

When the error light comes on with a buzzer and MSM says the waste tank is full, drain it and reset the counter. The steps are in the Long Store guide.

Not sure about a step? Text us a photo at (562) 609-4996.

Watch STS Inks' video: shaking the whites before waking the printer

More videos

STS Inks: why shaking your white ink matters
Mutoh: CR maintenance on XpertJet and ValueJet printers
STS Inks: 628 and 724 heat platen maintenance

Embedded from the manufacturer's official channel.

Common questions

What should I clean the wiper and head area with?

A dry cleaning stick, used once and thrown away. STS warns that a stick wet with water or solution can damage the print head, and that a reused stick carries dust onto it.

Can I use canned air inside the printer?

No. The manual says not to blow dust out with a gas duster because it can cause abnormal noise. Use a soft brush.

Should I turn the XPD-724 off at night?

No. STS designed it to stay on so its internal circulation runs overnight. Keep it on a surge protector, ideally a 500VA UPS.

The guidelines mention lubricating the rails and cleaning the encoder strip. How do I do that?

STS lists both as quarterly tasks but doesn't publish the step-by-step for owners, and opening the outer covers without STS's say-so voids the warranty. Text us and we'll walk you through it.

How do I know the flushing box absorber needs replacing?

Open the front cover and look at it. When lumps of ink rise above the frame of the flushing box, it's time. That's roughly every two months, depending on how much you print.

Sources
Did this fix it?