Support
Machine type
Brand
STS XPD-724 DTF Printer (Mutoh)

STS XPD-724 white ink not printing or clogging: the fix order STS recommends

✓ Reviewed by Jason KimUpdated 3 min readFits: XPD-724
Short answer

On the XPD-724, missing or patchy white is almost always settled white ink or dried ink around the head, not a dead print head. Shake both white cartridges the way STS specifies every day, then clean in order: Short or Normal cleaning, then Long, then clean the wiper and around the head, and only then Little Charge. If the head touched the film, stop and wet cap it with nozzle busting solution before you run more cleanings.

Match your symptom

What you see Most likely cause Go to
White gaps on the nozzle check first thing in the morning Settled white ink Steps 1 and 2
Gaps that come back during a run, or white drops out on big prints Partial clog, ink buildup around the head Steps 2 to 4
White suddenly gone after the film lifted or the head scraped it Head strike: film emulsion has gelled ink on the nozzles Step 5
Thin, dull white and colors with the white cartridge nearly empty Low ink Check ink levels in MSM and replace the cartridge

Step by step

  1. Shake the white the way STS specifies

    Do this every day before you wake the printer. Take both white cartridges out. Hold each one flat and shake it side to side about 40 times with the slot guide facing up, then again with it facing down. Then shake it upside down so everything mixes. Wipe any free ink off the end of the cartridge with a paper towel before you put it back.

  2. Print a nozzle check and clean only what needs it

    Open the printer driver's Printing Preferences and click Utility > Nozzle Check, or run it from the MSM remote panel. Print it on film so you can see the white rows. If there are gaps, run a cleaning from MSM's Printer Control (Short uses the least ink, Normal is the standard choice), then print another check. Repeat a few times.

  3. Step up to Long cleaning

    If several Normal cleanings don't clear the gaps, run Long cleaning. It uses more ink than Normal. Check again after each one.

  4. Clean the wiper and around the head, then Little Charge

    If several Long cleanings don't help, the wiper or the area around the head is usually dirty. In the driver go to Utility > Maintenance > CR Maintenance, click Start, then short press the operation key to bring the carriage to the maintenance position. With a dry cleaning stick, wipe both sides of the cleaning wiper and its base, then the silver metal around the head and the black plastic guides. Never touch the nozzle surface itself. Keep it under 5 minutes, close the cover and press the key again. Our daily and weekly maintenance guide has the full routine. If gaps are still there after that, run Little Charge, which cleans harder than Long but uses a lot of ink.

  5. If the head struck the film, wet cap it

    DTF film has a coating that turns ink into a gel the moment it lands. If the head touches the film, any ink on the nozzle plate gels too and blocks nozzles. Stop printing right away and run a head cleaning. Then fill the capping station with nozzle busting solution, make sure the head is parked in its locked home position over the cap (never over film), and turn the printer off for 6 hours or more. The next day, shake the white cartridges as usual and print a nozzle check.

Don't lift or touch the film while the printer is printing. STS does not cover print head damage caused by operator error, including head strikes.

Keep it from coming back

  • Leave the printer on so the white circulation runs overnight.
  • Shake the white every day, even if the nozzle check looked fine yesterday.
  • Clean the capping station seal and spit pad every second day, and the wiper weekly.
  • Keep the room in the range STS specifies. Dry air dries ink on the nozzles faster.
  • Don't use expired ink.

Still missing white after Little Charge? Stop cleaning and text us a photo of your latest nozzle check at (562) 609-4996.

Watch STS Inks' video: why shaking your white ink matters

More videos

STS Inks: shaking the whites before waking the printer
STS Inks: wet capping the 628 and 724 after a head strike

Embedded from the manufacturer's official channel.

Common questions

How many cleanings is too many?

STS warns that running cleaning after cleaning puts pressure on the print head and can make it delaminate and fail early. Work through the order in this guide instead of repeating the same cleaning. If a few rounds at each level don't help, stop and text us.

Why does white look fine on small logos but drop out on big prints?

Large solid white areas pull more ink than the head can supply when the white is settled or partly clogged. Shake the white cartridges, print a nozzle check on film, and clean the white channels before you print large white areas.

Can I print while one white nozzle row is still weak?

STS says that if nozzles don't fully recover, you can print in high quality mode (720 x 1080) or with double white in your RIP while you sort it out. Text us before you change your RIP settings so we can check your profile.

Does it help to turn the printer off at night?

No. STS designed the XPD-724 to stay on so its internal white circulation can run overnight. The only time it should be off is while you wet cap after a head strike.

I swapped the white cartridges between slots and it is still clogged. Now what?

If both slots show the same gaps with known good cartridges, the problem is in the head or the lines, not the cartridge. Stop cleaning and text us a photo of your nozzle check.

Sources
Did this fix it?