Machine type
Prestige XL series (L2, XL2, XL2 Pro, XL3, XL4)
DTF Station Prestige R2 Pro
DTF Station Prestige R1
DTF Station Prestige R2 (original)
Prestige X6
DTF Station Prestige A4
DTF Station Prestige A3+ and A3+ R
Epson SureColor G6070 DTF printer
Mimaki TxF300-1600
Mimaki TxF330-800
STS XPD-924D DTF Printer (Mutoh)
STS VJ-628D DTF Printer (Mutoh)
DTF Station Vega S17
STS XpertJet 1682D (XPJ-1682D) 64 inch DTF Printer
STS XPD-724 DTF Printer (Mutoh)
Hotronix Fusion IQ, Air Fusion IQ and Dual Air Fusion IQ
Geo Knight DK20S and DK20SP Digital Knight Swing-Away Presses
DTF Station Maxima and Proxima Dual Heat Presses
Hotronix Auto Open Clam and Hover Heat Press
DTF Station Prisma Auto Heat Press
DTF Station Prisma Dual Heat Press
DTF Station Prisma Swing Heat Press
Insta 718, 728 and 828 Automatic Swing-Away Heat Presses
DTF Station Prisma Sentry Heat Press
Geo Knight DC16 and DC16AP Digital Combo Swing-Away Presses
Geo Knight DK Digital Clamshell Presses: DK20, DK16, DKA Auto, DK8 Label and DK7 Cap
Hotronix Auto Open Cap Press and 360 IQ Hat Press
Hotronix Craft Heat Press 9 x 12
Hotronix Mighty Mug Heat Press
Insta 256 and 288 Manual Swing-Away Heat Presses
Insta 907 Dual Station Shuttle Label Heat Press
Viper MAXX pretreatment machine
Ecofreen Mister-T2 and Mister-T2 Pro pretreatment machines
Pearl Elite and Pearl PTM DTG pretreatment machines
Viper XPT-1000 pretreatment machine
Lawson Silver-Jet and Silver-Jet V2 DTG Pretreat Sprayers
Lawson Zoom-AE DTG pretreatment machine
Viper MINI handheld DTG pretreatment machine
Brand
Prestige XL series (L2, XL2, XL2 Pro, XL3, XL4)
DTF Station Prestige R2 Pro
DTF Station Prestige R1
DTF Station Prestige R2 (original)
Prestige X6
DTF Station Prestige A4
DTF Station Prestige A3+ and A3+ R
DTF Station Aries 124 UV DTF printer
Miro DTF Powder Shakers: Miro 13 Max, 16, 24 and 36
DTF Station Aries 213 and Aries 113 UV DTF printers
Seismo L16R and L24R DTF Powder Shaker and Dryer
Phoenix Air 16x20 DTF Curing Oven
DTF Station Maxima and Proxima Dual Heat Presses
DTF Station Prisma Auto Heat Press
DTF Station Prisma Dual Heat Press
DTF Station Prisma Swing Heat Press
DTF Station Vega S17
DTF Station Prisma Sentry Heat Press
DTF Station Seismo V36R DTF Powder Shaker and Dryer
DTF Station Arc 127 automatic cutter for DTF and UV DTF film
Epson SureColor F2100
Epson SureColor G6070 DTF printer
Epson SureColor F2270
Epson SureColor F3070
Epson SureColor F570
Epson SureColor F170
Epson SureColor F6470 and F6470H
Epson SureColor F6370
Epson SureColor F7200
Epson SureColor P-Series photo printers (P700, P900, P6570, P8570)
Epson SureColor T-Series CAD and technical printers
Epson SureColor S-Series (S40600, S60600, S80600)
STS XPD-924D calibration: fixing banding, white misalignment and white lines with Adjust Print, Adjust Head and PF Adjust
If XPD-924D prints look grainy or banded with a perfect nozzle check, run the print quality calibration (Menu 1 Setup, user type, Adjust Print). Try Auto first. For white and color layers that don't line up, run head alignment (Test Print 6 Adjust Head) and then Adjust Print again. For thin white lines or overlapping bands across the print, run the media feed adjustment (PF Adjust). Menu 10 Media Adjustment does Adjust Print and PF Adjust together with the color sensor.
The XPD-924D has two print heads and a built in color sensor. Mutoh gives owners three calibrations from the panel. Use them in this order when prints look wrong but every nozzle fires.
Match your symptom
| Symptom | What to run |
|---|---|
| Grainy or banded | Print quality calibration (Adjust Print). Colors can also look slightly doubled |
| Layers offset | White and color don't line up, or unidirectional prints look poor: head alignment (Adjust Head), then Adjust Print |
| White lines | Thin white lines or overlapping bands across the print: media feed adjustment (PF Adjust) |
| New film | New film type, new install, or roller pressure changed: PF Adjust, then Adjust Print |
Run a nozzle check first and clean until it is complete. Calibration can't fix missing nozzles. Load film straight, and warm the heater before printing patterns (answer No to Skip Heater Warm Up?). Don't touch the media guide while it says Warming Up. Adjust Print and Adjust Head need at least 550 mm of printable width, and PF Adjust needs 400 mm.
Quickest option: Media Adjustment
Menu 10 Media Adjustment runs print quality calibration and media feed adjustment together using the color sensor. Pick the user type, enter the film thickness (the default is 170 µm), and tap Enter. It ends with AutoAdjust Succeeded or AutoAdjust Failed. If it fails, run it again or use the manual methods below.
Print quality calibration (Adjust Print)
-
Open the menu
Tap Home, go to Menu 1 Setup > Setup 1 User Type, pick your user type, then step to Type ** : 2 Adjust Print. Enter the film thickness.
-
Try Auto first
Choose Adjust Print 1: Auto. Pick Standard to calibrate the print mode saved in this user type, or ALL to do patterns A to F. The printer prints, scans and corrects itself.
-
Manual if Auto fails
Use Adjust Print 2: Standard (only the user type's print mode, so the RIP must use the same resolution, passes and direction) or Adjust Print 3: Custom (all modes A to F). Print the Confirm Pattern first. If lines are offset, print the Rough Pattern, find the best aligned block for head 1 (numbered 1 to 21) and enter that number, then do head 2. Repeat with the Fine Pattern (1 to 7), checking both sides and the middle of the film.
On the 924D, the High Quality, Quality and Production modes use pattern F and High Speed uses pattern E. If your RIP sets head speed to Low, use pattern A, B or C.
Head alignment (Adjust Head)
-
When to use it
When Adjust Print doesn't fix the problem, when unidirectional prints look poor, or when you switch to thin film or film where ink doesn't spread.
-
Run it
Go to Menu 2 Test Print > Test Print 6 Adjust Head. Choose Adjust Head 3: Auto to let the color sensor do it, or Adjust Head 1: Standard or Adjust Head 2: Custom to read the pattern yourself and enter the number (1 to 7) with the fewest white lines or overlaps.
-
Always follow with Adjust Print
Mutoh says head alignment can shift bidirectional dot placement, so run Adjust Print again afterward.
Media feed adjustment (PF Adjust)
-
Auto
In the same user type, step to Type ** : 3 PF Adjust and choose PF Adjust 1: Auto.
-
Manual, with a ruler
If lines remain, choose PF Adjust 2: Initial Print (250 mm feed by default; longer is more accurate). Cut the print, measure between the marks, and enter that value in PF Adjust 3: Initial Change. Check it with PF Adjust 4: Confirm Print. When the measurement matches, print PF Adjust 5: Micro Print and enter the value under the block with the fewest white lines or overlaps.
-
Small corrections mid-job
While printing, Menu 5 PF Micro Adjust changes feed for the current job only (-5 to +5%). Save it to the user type with Menu 6 Backup.
Calibration values are saved per user type. Setup 1 > Copy User Type copies them to other types. If calibration won't settle, Text us a photo or short video at (562) 609-4996. Physical head adjustments with tools are for technicians.
Common questions
Which calibration should I run first?
Nozzle check first, then Adjust Print. Use Adjust Head only if Adjust Print doesn't fix it, and always run Adjust Print again after Adjust Head. Use PF Adjust for horizontal white lines or overlaps.
The panel says Cannot Operate, Outside Print Area. Why?
The test patterns need printable width: 550 mm for Adjust Print and Adjust Head, 400 mm for PF Adjust. Check your side margin and origin settings and that full width film is loaded.
Auto Adjust Failed. Now what?
Values for patterns that finished are kept. Reload the film flat and try again, or use the Standard or Custom manual method and read the pattern yourself.
Do I have to calibrate after changing film?
Run PF Adjust for a new film type or after changing roller pressure. Run Adjust Print after changing head height or if prints look worse on the new film.
Can I adjust the heads mechanically myself?
No. Physical alignment with tools and a microscope is technician work. Text us if the panel calibrations don't fix it.
- STS XPD-924D Operation Manual (v5)
- STS XPD-924D Setup Guide v2
- AA support requests about the STS XPD-924D, 2024 to 2026











































































