Support
Machine type
Brand
STS XPD-924D DTF Printer (Mutoh)

STS XPD-924D clogged nozzles or weak white: the cleaning order, and what to do after a head strike

✓ Reviewed by Jason KimUpdated 3 min readFits: XPD-924D
Short answer

Shake the white cartridges, print a nozzle check, and clean only the head that has gaps: Short or Normal first, then Long, then clean the wiper, caps and around the heads, and finally Little Charge. After a head strike, stop, clean, then soak the heads for 99 minutes from Menu 12 with Nozzle Busting solution in the capping station. Avoid repeated cleanings, which STS says can damage the head.

Match your symptom

What you see Likely cause Go to
White gaps first thing in the morning Settled white ink Steps 1 and 2
Gaps in one head only Partial clog in that head Steps 2 and 3
Gaps come back after several cleanings Dirty wiper, caps or head area, worn wiper or full flushing box Step 4
Nozzles vanish after the head touched the film Head strike: the film coating gels the ink on the nozzles Step 6
Lines fine on the check but prints blurred or banded Calibration, not clogging Our 924D error and media guide

Step by step

  1. Shake the white properly

    Settled white is the most common cause of weak or missing white. Remove both white cartridges and shake them flat, side to side, slot guide up and then down, for 2 to 3 minutes. Do it every day before waking the printer.

  2. Print a nozzle check and clean only the head that needs it

    Print a nozzle check on film. If gaps show in one head, open Menu 3 Cleaning and choose Select Print Head: Head 1 or Head 2 cleans only that head and wastes less ink than ALL. Start with Short or Normal, then print another check.

  3. Step up to Long

    If two or three Normal cleanings don't clear it, run Long. It uses more ink. Check after each one.

  4. Clean the wiper, caps and around the head

    If several Long cleanings don't help, the parts that wipe and cap the heads are usually dirty. Run Menu 11 CR Maintenance and clean the wiper, capping station, spit pad and the area around the heads with dry cleaning sticks (our daily and weekly guide shows how). Also check that the flushing box absorber isn't overflowing, that the wiper is less than 12 months old, and that its color matches your head height: black for Low1, Low2 and Middle, grey for High. The wrong wiper can't clean properly.

  5. Little Charge, then stop

    If gaps remain, run Little Charge from Menu 3 Cleaning > Cleaning Type. It cleans harder than Long but uses a lot of ink. Don't power off, open covers or pull cartridges while it runs. If nozzles still don't recover, stop cleaning and text us your latest nozzle check. Mutoh's last resort is Setup 21 Select Nozzle, which prints with only the nozzles that work, and STS suggests printing in a high quality mode in the meantime.

  6. After a head strike: soak the heads

    Stop printing at once and run a head cleaning. Then tap Home and open Menu 12 (the head moves left) to start head soaking. Set the timer to 99 minutes. Fill the capping station with STS Nozzle Busting solution and let the timer run out. If the nozzles still haven't recovered, STS says to put Nozzle Busting solution in the cap, power the printer down and leave it overnight. The next day, shake the whites as usual and print a nozzle check.

Don't clean over and over. STS warns that sustained head cleanings put pressure on the print head and can make it delaminate and fail early. Running cleanings every 15 to 20 minutes is a sign something else is wrong: text us instead. STS does not cover head damage from head strikes or from touching or lifting the film while printing.

Stop it happening again

  • Never lift, touch or move the film while the printer is running, and print with the front cover down.
  • Never park the head on the film. Remove the film before moving the head by hand.
  • Keep the printer at least 50 cm (about 1.6 ft) from any powder shaker so powder can't drift in.
  • In a hot or dry room, set Sleep Mode auto cleaning to every 4 hours or less, and STS suggests occasionally spitting ink onto scrap film to keep nozzles wet.
  • Use XPD2 ink only, never past its expiry date.

Text us a photo or short video at (562) 609-4996 with your nozzle check if you get stuck at any step.

Watch STS: why shaking your white DTF ink matters

More videos

STS: CR Maintenance on the XPD-924D, step by step

Embedded from the manufacturer's official channel.

Common questions

How many cleanings is too many?

STS does not give a number, but it warns that sustained cleanings can delaminate the head. If two or three Normal and a Long cleaning haven't helped, clean the wiper and caps instead of cleaning again.

Where is the head soak menu?

STS gives the path as Home, then Menu 12. The head moves to the left. Set the soak time to 99 minutes.

Does a head strike void the warranty?

STS says it will not cover print head damage from head strikes or from lifting or touching the film while printing.

The white is weak but the nozzle check looks complete.

Shake the white cartridges properly first. Settled pigment prints thin even when every nozzle fires. If it stays weak, check ink levels and text us a photo of a print.

Can Select Nozzle fix a clog?

No. It tells the printer to use only the nozzles that fire, so you can keep printing. It is a workaround while you contact us.

Did this fix it?