Machine type
Prestige XL series (L2, XL2, XL2 Pro, XL3, XL4)
DTF Station Prestige R2 Pro
DTF Station Prestige R1
DTF Station Prestige R2 (original)
Prestige X6
DTF Station Prestige A4
DTF Station Prestige A3+ and A3+ R
Epson SureColor G6070 DTF printer
Mimaki TxF300-1600
Mimaki TxF330-800
STS XPD-924D DTF Printer (Mutoh)
STS VJ-628D DTF Printer (Mutoh)
DTF Station Vega S17
STS XpertJet 1682D (XPJ-1682D) 64 inch DTF Printer
STS XPD-724 DTF Printer (Mutoh)
Hotronix Fusion IQ, Air Fusion IQ and Dual Air Fusion IQ
Geo Knight DK20S and DK20SP Digital Knight Swing-Away Presses
DTF Station Maxima and Proxima Dual Heat Presses
Hotronix Auto Open Clam and Hover Heat Press
DTF Station Prisma Auto Heat Press
DTF Station Prisma Dual Heat Press
DTF Station Prisma Swing Heat Press
Insta 718, 728 and 828 Automatic Swing-Away Heat Presses
DTF Station Prisma Sentry Heat Press
Geo Knight DC16 and DC16AP Digital Combo Swing-Away Presses
Geo Knight DK Digital Clamshell Presses: DK20, DK16, DKA Auto, DK8 Label and DK7 Cap
Hotronix Auto Open Cap Press and 360 IQ Hat Press
Hotronix Craft Heat Press 9 x 12
Hotronix Mighty Mug Heat Press
Insta 256 and 288 Manual Swing-Away Heat Presses
Insta 907 Dual Station Shuttle Label Heat Press
Viper MAXX pretreatment machine
Ecofreen Mister-T2 and Mister-T2 Pro pretreatment machines
Pearl Elite and Pearl PTM DTG pretreatment machines
Viper XPT-1000 pretreatment machine
Lawson Silver-Jet and Silver-Jet V2 DTG Pretreat Sprayers
Lawson Zoom-AE DTG pretreatment machine
Viper MINI handheld DTG pretreatment machine
Brand
Prestige XL series (L2, XL2, XL2 Pro, XL3, XL4)
DTF Station Prestige R2 Pro
DTF Station Prestige R1
DTF Station Prestige R2 (original)
Prestige X6
DTF Station Prestige A4
DTF Station Prestige A3+ and A3+ R
DTF Station Aries 124 UV DTF printer
Miro DTF Powder Shakers: Miro 13 Max, 16, 24 and 36
DTF Station Aries 213 and Aries 113 UV DTF printers
Seismo L16R and L24R DTF Powder Shaker and Dryer
Phoenix Air 16x20 DTF Curing Oven
DTF Station Maxima and Proxima Dual Heat Presses
DTF Station Prisma Auto Heat Press
DTF Station Prisma Dual Heat Press
DTF Station Prisma Swing Heat Press
DTF Station Vega S17
DTF Station Prisma Sentry Heat Press
DTF Station Seismo V36R DTF Powder Shaker and Dryer
DTF Station Arc 127 automatic cutter for DTF and UV DTF film
Epson SureColor F2100
Epson SureColor G6070 DTF printer
Epson SureColor F2270
Epson SureColor F3070
Epson SureColor F570
Epson SureColor F170
Epson SureColor F6470 and F6470H
Epson SureColor F6370
Epson SureColor F7200
Epson SureColor P-Series photo printers (P700, P900, P6570, P8570)
Epson SureColor T-Series CAD and technical printers
Epson SureColor S-Series (S40600, S60600, S80600)
STS XPD-924D error messages, E-code restarts and film jams: what each message means and how to clear it
Most XPD-924D messages point to something you can fix yourself: close a cover, lower the media lever, reload the film straight, or empty the waste tank. If every light blinks and the buzzer sounds with an E code, remove anything blocking the carriage, restart, and contact us with the code if it returns. For a jam, power off, slide the carriage aside, release the pressure rollers and cut the damaged film away.
First, open MSM and check Printer Status > Status Information, and make sure MSM is up to date (Help > Version > Check for updates). For S/C card and cartridge messages, use our S/C card guide.
Panel messages and what to do
| Message | What to do |
|---|---|
| Cover Open | Close the front cover and both maintenance covers |
| Put Lever Back | Lower the media feed lever so the pressure rollers grip |
| Hold Media, Undefined Media, Media Slant | Reload the film straight. Use fresh film, not film that has been printed on |
| Media Cut Error | The film wasn't cut. Check the path. A worn cutter blade is a user part: text us for the steps |
| Change Head Gap *** | The head height on the printer doesn't match the print job. Set the job and printer to the same height, or text us |
| End Of Roll | Load a new roll |
| Full WasteInkTank | Empty the waste ink tank now. The printer stops until you do |
| [slot] Discharged | Ink isn't filled. Run Initial Charge (see our Long Store guide) |
| Cannot Operate, Outside Print Area | Not enough printable width. Check media width, origin and side margins |
| Remote Mode | MSM has control. Hold Enter for more than two seconds to end it |
| Life Times [pump or motor] | A part is near the end of its life. You can keep printing; contact us |
| E***Err, all lights blinking | An error that needs a restart (below) |
Error that needs a restart
-
Silence it and note the code
Press any key to stop the buzzer. Write down the code number shown after the E.
-
Look for the cause
Look for scraps of film or anything blocking the carriage or feed path. If you just replaced a part, check it is fitted correctly.
-
Restart
Turn the printer off with the power button, wait a short while, and turn it back on. If the same code comes back, stop and contact us with the code number.
Clearing a film jam
-
Power off
Hold the Power button until Power Off appears.
-
Move the carriage
Open the front cover and slide the carriage off the film to the right. If the head height is set to Low1 or Low2, Mutoh says to raise it to High first and set it back afterward.
-
Free the film
Slide the edge holder off the film to the right. If it is bent, stop using it and contact us. Pull the media feed lever toward you to release the pressure rollers.
-
Cut and rewind
Pull the film toward you, cut off the damaged part along the groove, and rewind a little by turning the flange on the media holder. Remove any scraps left inside.
-
Check the heads
Turn the printer on, reload the film and print a nozzle check. A jam can touch the heads, so clean if anything is missing.
Print problems with no message
| Symptom | Check |
|---|---|
| Carriage pauses at the sides | Use a Category 6 Gigabit Ethernet cable. In MSM, make sure MUTOH Print Server (MPS) is enabled and your computer meets Mutoh's minimum: Windows 8.1 or later, Core i5, 8 GB |
| Smears or missing patches | Film curling or wrinkled, dirt around the heads. The heater can warp film that waits before printing: Setup 23 Start Feed feeds more before the job |
| Lines or banding | Nozzle check first. Then run print quality adjustment and media feed adjustment from the calibration menus |
| Colors wrong | Expired ink, clogged nozzles, or a cartridge in the wrong slot |
| Film slips or crumples while loading | Set edge holders on both edges, check the vacuum fan setting, use flat film |
Text us a photo or short video at (562) 609-4996 of the panel and your nozzle check if the message isn't listed here.
Common questions
All the lights are blinking and it keeps beeping.
That is an error that needs a restart. Press any key to stop the beep, note the E code, clear any obstruction, then power off and on. If the same code comes back, contact us with the number.
What does Change Head Gap mean?
The head height set on the printer doesn't match the height in the print job. They must match before it will print.
The carriage stops at each side during printing.
Mutoh links this to the connection: use a Category 6 Gigabit cable and check that MPS is enabled in MSM.
Where do I see more detail on an error?
In MSM under Printer Status, Status Information. Keep MSM updated through Help, Version, Check for updates.
The panel shows an S/C card error.
Use our S/C card guide. It covers Read Err, Col. Err, Broken Chip and smartchip recovery for the 924D.
- STS XPD-924D Operation Manual (v5)
- Mutoh Status Monitor (MSM) Operation Manual
- AA support requests about XPD-924D errors and film jams, 2024 to 2026











































































