Machine type
Prestige XL series (L2, XL2, XL2 Pro, XL3, XL4)
DTF Station Prestige R2 Pro
DTF Station Prestige R1
DTF Station Prestige R2 (original)
Prestige X6
DTF Station Prestige A4
DTF Station Prestige A3+ and A3+ R
Epson SureColor G6070 DTF printer
Mimaki TxF300-1600
Mimaki TxF330-800
STS XPD-924D DTF Printer (Mutoh)
STS VJ-628D DTF Printer (Mutoh)
DTF Station Vega S17
STS XpertJet 1682D (XPJ-1682D) 64 inch DTF Printer
STS XPD-724 DTF Printer (Mutoh)
Hotronix Fusion IQ, Air Fusion IQ and Dual Air Fusion IQ
Geo Knight DK20S and DK20SP Digital Knight Swing-Away Presses
DTF Station Maxima and Proxima Dual Heat Presses
Hotronix Auto Open Clam and Hover Heat Press
DTF Station Prisma Auto Heat Press
DTF Station Prisma Dual Heat Press
DTF Station Prisma Swing Heat Press
Insta 718, 728 and 828 Automatic Swing-Away Heat Presses
DTF Station Prisma Sentry Heat Press
Geo Knight DC16 and DC16AP Digital Combo Swing-Away Presses
Geo Knight DK Digital Clamshell Presses: DK20, DK16, DKA Auto, DK8 Label and DK7 Cap
Hotronix Auto Open Cap Press and 360 IQ Hat Press
Hotronix Craft Heat Press 9 x 12
Hotronix Mighty Mug Heat Press
Insta 256 and 288 Manual Swing-Away Heat Presses
Insta 907 Dual Station Shuttle Label Heat Press
Viper MAXX pretreatment machine
Ecofreen Mister-T2 and Mister-T2 Pro pretreatment machines
Pearl Elite and Pearl PTM DTG pretreatment machines
Viper XPT-1000 pretreatment machine
Lawson Silver-Jet and Silver-Jet V2 DTG Pretreat Sprayers
Lawson Zoom-AE DTG pretreatment machine
Viper MINI handheld DTG pretreatment machine
Brand
Prestige XL series (L2, XL2, XL2 Pro, XL3, XL4)
DTF Station Prestige R2 Pro
DTF Station Prestige R1
DTF Station Prestige R2 (original)
Prestige X6
DTF Station Prestige A4
DTF Station Prestige A3+ and A3+ R
DTF Station Aries 124 UV DTF printer
Miro DTF Powder Shakers: Miro 13 Max, 16, 24 and 36
DTF Station Aries 213 and Aries 113 UV DTF printers
Seismo L16R and L24R DTF Powder Shaker and Dryer
Phoenix Air 16x20 DTF Curing Oven
DTF Station Maxima and Proxima Dual Heat Presses
DTF Station Prisma Auto Heat Press
DTF Station Prisma Dual Heat Press
DTF Station Prisma Swing Heat Press
DTF Station Vega S17
DTF Station Prisma Sentry Heat Press
DTF Station Seismo V36R DTF Powder Shaker and Dryer
DTF Station Arc 127 automatic cutter for DTF and UV DTF film
Epson SureColor F2100
Epson SureColor G6070 DTF printer
Epson SureColor F2270
Epson SureColor F3070
Epson SureColor F570
Epson SureColor F170
Epson SureColor F6470 and F6470H
Epson SureColor F6370
Epson SureColor F7200
Epson SureColor P-Series photo printers (P700, P900, P6570, P8570)
Epson SureColor T-Series CAD and technical printers
Epson SureColor S-Series (S40600, S60600, S80600)
STS XPD-924D loading a film roll: flanges, media holders, pressure rollers, edge holders and side margin
To load film on the XPD-924D, lock the flanges into the core and set the roll on the media holders. Lift the pressure rollers, feed the film in from the back and pull out about 1 m at the front. Then rewind it straight while someone holds the edge, and line the right edge up with the guide line. Push the lever to normal pressure, place the edge holders, set a side margin of at least 10 mm and pick the user type.
Most XPD-924D film problems (skewed prints, film not detected, wrinkles that touch the heads) start at loading. Mutoh's method takes two people for a full roll: one holds the leading edge while the other rewinds it straight.
Film the 924D takes
| Spec | Limit |
|---|---|
| Width | 600 to 609 mm (24 in) |
| Core | 2 in or 3 in |
| Roll diameter | 200 mm max |
| Roll weight | 30 kg max |
Let a new roll sit in the print room for an hour before loading so it adjusts to the temperature and humidity. Don't use film that is creased, cut or torn, and don't touch the print side.
Load the roll
-
Fit the flanges
For a 2 in core, take the 3 in adapters off both media flanges first. Unlock each flange by turning its handle counterclockwise, push one into each end of the core, then turn the handles clockwise until they are firmly locked. A loose flange lets the roll slip and hurts print quality.
-
Set the roll on the holders
Loosen the knob bolt on the right media holder. Lower the roll gently onto the left holder, then slide the right holder in to take the right flange, and tighten its knob bolt. Don't drop the roll on the holders. Keep the left holder within 450 mm of the left end, or the printer can't detect the film.
-
Release the pressure rollers
Use the media feed lever to lift the pressure rollers (you can reach it from the front or the back). Open the front cover.
-
Feed the film
From the back, rewind any slack, then push the leading edge into the media slot. From the front, pull out about 1 m of film.
-
Straighten it
One person holds the leading edge while the other turns the flange to rewind slightly. This takes out warp and skew. Let go of the edge and the film can fall out of the slot.
-
Line up the right edge
The right edge of the film must sit just left of the media guide line. If it doesn't, print quality suffers.
-
Lock the rollers
Push the media feed lever until it clicks for normal pressure. Both edges of the film must be under rollers. If an edge isn't, release the lever and shift the media holders until it is.
-
Place the edge holders
Lift the tab on each edge holder and set it over the film edge. Normally the hole in each holder faces outward. For thin or soft film you can swap left and right holders so they hold a wider strip.
-
Set the side margin
Go to Menu 1 Setup > Setup 3 Side Margin and set at least 10 mm (the range is 5 to 25 mm). The default 5 mm lets ink land on the edge holders.
-
Finish
Close the front cover. At User: Type** OK?, choose the user type that matches this film and tap Enter. The printer initializes the film.
Pressure, head height and calibration
- The media feed lever has two settings: Normal (push until it clicks) for film, and High (push all the way) for heavy media. Each roller also has a slide lock to reduce or cancel its pressure, for film that cockles.
- Every time you change the lever or a slide lock, run a media feed adjustment (PF Adjust). Every time you change the head height lever, run a print quality calibration. Both are in our calibration guide.
- Normal head height is Low1 (film up to 0.3 mm). Go higher only if the head strikes, and match the wiper: black for Low1, Low2 and Middle, grey for High.
If the film won't load or skews
| Symptom | Check |
|---|---|
| Not detected | Left holder within 450 mm of the left end, film loaded straight, fresh film (not previously printed) |
| Skews | Reload and rewind it straight with the edge held |
| Wrinkles | Edge holders on, reduce the rollers at the edges, lower the heaters, reload |
| Outside Print Area | Not enough printable width for a test pattern: check the side margin and origin |
Text us a photo or short video at (562) 609-4996 if the film still runs crooked after a careful reload.
Common questions
Why does Mutoh want a 10 mm side margin?
The default is 5 mm, and the edge holders overlap the film edge. With a 5 mm margin they can pick up ink and smear it.
The printer says no media even though film is loaded. Why?
Check that the left media holder is within 450 mm of the left end, that the film went in straight, and that you aren't reusing film that was printed before.
Do I need to recalibrate after changing film?
Run a media feed adjustment when you use a new type of film or change the roller pressure. If prints look grainy or banded after a film change, run a print quality calibration too.
Can I load film alone?
For a light roll, maybe. Mutoh's method uses two people, one to hold the leading edge while the other rewinds. Letting go of the edge can pull the film out of the slot.
- STS XPD-924D Operation Manual (v5)
- STS XPD-924D Setup Guide v2
- AA support requests about the STS XPD-924D, 2024 to 2026











































































