Support
Machine type
Brand
STS XPD-924D DTF Printer (Mutoh)

STS XPD-924D Long Store and Initial Charge: storing the printer and bringing it back

✓ Reviewed by Jason KimUpdated 2 min readFits: XPD-924D
Short answer

If the XPD-924D will sit idle for more than 5 business days, run Long Store from Setup 17 (or MSM): it discharges the ink, washes the heads twice with six cleaning cartridges, and leaves them discharged and ready for power off. STS also wants a Long Store every 3 to 4 months to clear sediment. To restart, power on, run Initial Charge with shaken cartridges, then print a nozzle check and use Little Charge if lines are missing.

When to run it

Situation What to do
Idle more than 5 business days Long Store before the break. STS says a longer idle risks clogs and may void the warranty
Every 3 to 4 months Long Store, then Initial Charge, to flush sediment from the lines
Short quiet spell A daily head cleaning, or the STS test print three times a week
Moving the printer Empty the waste tank first and keep it level. Call us before shipping it

Run Long Store

  1. Get ready

    You need six STS cleaning cartridges for the 924D, one for each slot. Contact us if you don't have them. Empty the waste ink tank first: it holds 2,000 ml, so drain it into a container at least that big.

  2. Start it

    Tap Home, open Menu 1 Setup, step to Setup 17 Longstore and tap Enter at Start -> Enter. STS says you can also start it from the MSM dashboard and follow the screens there.

  3. Remove the ink cartridges

    When the panel says Remove Cartridges, take all of them out. Keep each with its S/C card. The printer discharges the ink.

  4. First wash

    When it asks, insert a cleaning cartridge in every slot. The panel shows Washing Head while it fills with cleaner. When it asks, remove them all and it discharges the cleaner.

  5. Second wash

    Insert the cleaning cartridges again when asked, then remove them again when asked. When it finishes, the panel shows [ALL] Discharged.

  6. Power off

    Hold the Power button until Power Off appears, then let go. The Power LED goes out.

Bring it back with Initial Charge

  1. Power on

    Hold the Power button until the Power LED lights, then let go.

  2. Start the charge

    At Ink Charge Start -> Enter, tap Enter. At Wash Retry? No, tap Enter to go straight to ink. If you want another wash first, change it to Wash Retry? Yes and follow the panel.

  3. Shake and insert ink

    When it shows Insert Ink Cartridges, shake the whites for 2 to 3 minutes, then push each cartridge fully into the slot whose color label matches.

  4. Wait it out

    The panel shows Ink Refill **%. While it charges, don't turn the printer off, unplug it, open the front or maintenance covers, or release the pressure rollers. It's done when the panel shows Media End.

  5. Check the nozzles

    Load film and print a nozzle check. Lines are often blurred or missing straight after a charge. If so, run Little Charge from Menu 3 Cleaning. If that doesn't fix it, leave the printer alone for an hour or more and run Little Charge again.

If the charge won't start or ink won't flow

  • Close the front and maintenance covers and lower the media loading lever.
  • Make sure every cartridge and S/C card is fully seated.
  • Ink that has been in a cold vehicle or warehouse should sit at room temperature for at least three hours. Then run a few cleanings.
  • If the power went off during charging, turn it back on and let the charge continue.

Still not right after the second Little Charge? Text us a photo or short video at (562) 609-4996 with your nozzle check.

Common questions

How long can the 924D sit with ink in it?

STS's newest guidelines say no more than 5 business days without printing or maintenance. Its older guidelines said 7 days. Use the stricter number.

Can I just turn it off for a long weekend?

STS says to leave it on in Sleep Mode so it can circulate ink and clean itself. Only Long Store and then power off for longer breaks.

Do I need to drain the waste tank first?

Yes. Long Store and Initial Charge both push a lot of fluid into the tank. Empty it before you start.

My nozzle check is messy right after the charge.

That is normal. Run Little Charge. If it's still bad, wait an hour or more and run it again. If that doesn't fix it, contact us.

Where do I get cleaning cartridges for the 924D?

Contact us. Make sure they are the cleaning cartridges made for the 924D, one per slot.

Did this fix it?