Machine type
Prestige XL series (L2, XL2, XL2 Pro, XL3, XL4)
DTF Station Prestige R2 Pro
DTF Station Prestige R1
DTF Station Prestige R2 (original)
Prestige X6
DTF Station Prestige A4
DTF Station Prestige A3+ and A3+ R
Epson SureColor G6070 DTF printer
Mimaki TxF300-1600
Mimaki TxF330-800
STS XPD-924D DTF Printer (Mutoh)
STS VJ-628D DTF Printer (Mutoh)
DTF Station Vega S17
STS XpertJet 1682D (XPJ-1682D) 64 inch DTF Printer
STS XPD-724 DTF Printer (Mutoh)
Hotronix Fusion IQ, Air Fusion IQ and Dual Air Fusion IQ
Geo Knight DK20S and DK20SP Digital Knight Swing-Away Presses
DTF Station Maxima and Proxima Dual Heat Presses
Hotronix Auto Open Clam and Hover Heat Press
DTF Station Prisma Auto Heat Press
DTF Station Prisma Dual Heat Press
DTF Station Prisma Swing Heat Press
Insta 718, 728 and 828 Automatic Swing-Away Heat Presses
DTF Station Prisma Sentry Heat Press
Geo Knight DC16 and DC16AP Digital Combo Swing-Away Presses
Geo Knight DK Digital Clamshell Presses: DK20, DK16, DKA Auto, DK8 Label and DK7 Cap
Hotronix Auto Open Cap Press and 360 IQ Hat Press
Hotronix Craft Heat Press 9 x 12
Hotronix Mighty Mug Heat Press
Insta 256 and 288 Manual Swing-Away Heat Presses
Insta 907 Dual Station Shuttle Label Heat Press
Viper MAXX pretreatment machine
Ecofreen Mister-T2 and Mister-T2 Pro pretreatment machines
Pearl Elite and Pearl PTM DTG pretreatment machines
Viper XPT-1000 pretreatment machine
Lawson Silver-Jet and Silver-Jet V2 DTG Pretreat Sprayers
Lawson Zoom-AE DTG pretreatment machine
Viper MINI handheld DTG pretreatment machine
Brand
Prestige XL series (L2, XL2, XL2 Pro, XL3, XL4)
DTF Station Prestige R2 Pro
DTF Station Prestige R1
DTF Station Prestige R2 (original)
Prestige X6
DTF Station Prestige A4
DTF Station Prestige A3+ and A3+ R
DTF Station Aries 124 UV DTF printer
Miro DTF Powder Shakers: Miro 13 Max, 16, 24 and 36
DTF Station Aries 213 and Aries 113 UV DTF printers
Seismo L16R and L24R DTF Powder Shaker and Dryer
Phoenix Air 16x20 DTF Curing Oven
DTF Station Maxima and Proxima Dual Heat Presses
DTF Station Prisma Auto Heat Press
DTF Station Prisma Dual Heat Press
DTF Station Prisma Swing Heat Press
DTF Station Vega S17
DTF Station Prisma Sentry Heat Press
DTF Station Seismo V36R DTF Powder Shaker and Dryer
DTF Station Arc 127 automatic cutter for DTF and UV DTF film
Epson SureColor F2100
Epson SureColor G6070 DTF printer
Epson SureColor F2270
Epson SureColor F3070
Epson SureColor F570
Epson SureColor F170
Epson SureColor F6470 and F6470H
Epson SureColor F6370
Epson SureColor F7200
Epson SureColor P-Series photo printers (P700, P900, P6570, P8570)
Epson SureColor T-Series CAD and technical printers
Epson SureColor S-Series (S40600, S60600, S80600)
STS XPD-924D setup and first print: unpacking, activation, wiper, initial ink charge and nozzle check
Set up an XPD-924D in this order: build the stand, mount the printer with four people, and remove the front cover locks before you open the cover. Then fit the waste tank and both power cords, enter the network settings, and activate the printer with the code from your dealer. Fit the cleaning wiper and run the initial cleaning with six cleaning cartridges. Next, charge the six ink cartridges, load film and print Nozzle Check F. Finish with the media feed adjustment before your first real print.
This is the order STS and Mutoh give for bringing a new XPD-924D from the crate to its first nozzle check. Most shops have this done by an installer, but it helps to know each step, and you repeat several of them (activation, wiper, film loading, calibration) later on.
Lifting the printer onto its stand takes at least four people. The printer body alone weighs about 140 kg. Keep it level the whole time, or ink and parts inside can be damaged.
Before the day
- Power: the 924D has two power cords, one for the printer and one for the heater. At 120 V the manual lists up to 9 A for the printer and 10 A for the heater. Plug both into grounded wall outlets on the same voltage, never a power strip, and don't put both on one outlet if that would overload it.
- Room: a level floor that can take the weight, no direct sun, no fan or air conditioner blowing on the printer, and stable temperature and humidity.
- Computer: Windows 11, 10 or 8.1, an Intel Core i5 or i7, at least 8 GB of memory, and a Gigabit Ethernet port with a Category 6 cable.
- Supplies: six cleaning cartridges, six XPD2 ink cartridges (black, cyan, magenta, yellow and two white), a roll of 24 inch film, and a Phillips screwdriver.
Unpack and assemble
-
Build the stand
Bolt the left and right legs to the brace, then the feet, the fixing brackets and the waste tank holder (on the right leg). Shake it to check every joint, then screw the leveling adjusters down until the stand can't roll.
-
Mount the printer
With four people, lift the printer onto the stand and fix it with the eight wing bolts.
-
Remove the shipping locks in order
Peel the packing tape off the covers. Take out the two screws holding the front cover locks before you open the front cover, or the cover can be damaged. Then open it, remove the two lock plates and the wing bolt holding the shipping bracket on the carriage, pull out the protective material, and slide the edge holders to the far left and right. Keep every lock, bracket and screw for the next move.
-
Fit the waste ink tank
Set the tank in its holder, push the waste tube firmly into its mouth with no kink in the tube, and plug in the waste sensor cable. A loose or bent tube spills ink.
-
Connect power and network
With the front cover closed, connect both power cords and the Ethernet cable, and secure the cable with the supplied tie.
First power on
-
Initial settings
Long press the Power button until the light comes on. Pick the language, temperature unit and length unit, then enter the IP address, subnet mask and gateway your network uses. The printer then initializes.
-
Activate the printer
When the panel shows Activation required, tap Enter and type the 16 digit activation code. Text us for your code. After Activation Succeeded, long press Power to turn it off, wait a few seconds, and turn it back on.
-
Install the cleaning wiper
At Install Wiper, open the front cover and the right maintenance cover. Seat the back of the wiper first, then press the front down until it clicks. Don't touch the rubber with bare hands: skin oil damages the heads. Close both covers and choose Installed Wiper? Yes.
-
Initial cleaning
At Ink Charge Start -> Enter, tap Enter, choose Wash Retry? Yes and insert the six cleaning cartridges. The printer fills with cleaner, asks you to remove the cartridges, then drains. Keep each cleaning cartridge with its own S/C card. Choose Wash Retry? No to finish.
-
Initial ink charge
At Insert InkCartridges, shake the two whites, then insert all six ink cartridges. Stick the supplied ink slot labels on in the correct color order. The panel counts up Ink Refill %. It is done when the panel shows Media End.
While ink is charging, do not turn the printer off, unplug it, open the front or maintenance covers, or release the pressure rollers.
Load film and print a nozzle check
-
Load the film
Load the roll as in our film loading guide. Set Setup 3 Side Margin to at least 10 mm, because the edge holders can pick up ink where they overlap the film, then pick the user type to finish loading.
-
Print Nozzle Check F
Run Nozzle Check F from the panel. It prints the color and white rows with the date, serial number and firmware version beside them.
-
Faded right after the charge?
That is common straight after an initial charge. Run Little Charge from the cleaning menu. If it still looks faded, leave the printer for at least an hour, then clean or Little Charge again. If lines are still missing after that, contact us.
-
Clean if needed
For a few missing lines, run a Short or Normal cleaning and print the check again until every line is there.
Connect the computer and calibrate
Install the Mutoh Status Monitor (MSM) from the Startup Assistant package you download after registering (the registration sheet is in the box), then register the printer by its IP address. Before you print a real image, Mutoh requires a media feed adjustment, and a print quality calibration is recommended. Both are in our XPD-924D calibration guide.
Text us a photo or short video at (562) 609-4996 if any step stops with a message you don't recognize.
Common questions
Where do I get the activation code?
From your dealer. If you bought the printer from us, text us and we'll send it. Mutoh also offers activation through its MUTOH Club registration.
Can I plug both power cords into one outlet?
Only if that outlet can carry both loads together. At 120 V the printer draws up to 9 A and the heater up to 10 A. If in doubt, use two separate grounded outlets on the same voltage. Never use a power strip.
The nozzle check is faded right after the ink charge. Is something wrong?
Not necessarily. Mutoh says this happens. Run Little Charge, and if it is still faded, wait at least an hour and clean or Little Charge again. Contact us if lines are still missing.
Do I need to keep the shipping brackets?
Yes. Keep the front cover locks, lock plates, carriage shipping bracket and their screws. You need them to move the printer safely.
What computer do I need?
Windows 11, 10 or 8.1 with an Intel Core i5 or i7, at least 8 GB of memory and a Gigabit Ethernet port with a Category 6 cable.
- STS XPD-924D Setup Guide v2
- STS XPD-924D Operation Manual (v5)
- Mutoh Status Monitor (MSM) Operation Manual
- AA support requests about the STS XPD-924D, 2024 to 2026











































































