Machine type
Prestige XL series (L2, XL2, XL2 Pro, XL3, XL4)
DTF Station Prestige R2 Pro
DTF Station Prestige R1
DTF Station Prestige R2 (original)
Prestige X6
DTF Station Prestige A4
DTF Station Prestige A3+ and A3+ R
Epson SureColor G6070 DTF printer
Mimaki TxF300-1600
Mimaki TxF330-800
STS XPD-924D DTF Printer (Mutoh)
STS VJ-628D DTF Printer (Mutoh)
DTF Station Vega S17
STS XpertJet 1682D (XPJ-1682D) 64 inch DTF Printer
STS XPD-724 DTF Printer (Mutoh)
Hotronix Fusion IQ, Air Fusion IQ and Dual Air Fusion IQ
Geo Knight DK20S and DK20SP Digital Knight Swing-Away Presses
DTF Station Maxima and Proxima Dual Heat Presses
Hotronix Auto Open Clam and Hover Heat Press
DTF Station Prisma Auto Heat Press
DTF Station Prisma Dual Heat Press
DTF Station Prisma Swing Heat Press
Insta 718, 728 and 828 Automatic Swing-Away Heat Presses
DTF Station Prisma Sentry Heat Press
Geo Knight DC16 and DC16AP Digital Combo Swing-Away Presses
Geo Knight DK Digital Clamshell Presses: DK20, DK16, DKA Auto, DK8 Label and DK7 Cap
Hotronix Auto Open Cap Press and 360 IQ Hat Press
Hotronix Craft Heat Press 9 x 12
Hotronix Mighty Mug Heat Press
Insta 256 and 288 Manual Swing-Away Heat Presses
Insta 907 Dual Station Shuttle Label Heat Press
Viper MAXX pretreatment machine
Ecofreen Mister-T2 and Mister-T2 Pro pretreatment machines
Pearl Elite and Pearl PTM DTG pretreatment machines
Viper XPT-1000 pretreatment machine
Lawson Silver-Jet and Silver-Jet V2 DTG Pretreat Sprayers
Lawson Zoom-AE DTG pretreatment machine
Viper MINI handheld DTG pretreatment machine
Brand
Prestige XL series (L2, XL2, XL2 Pro, XL3, XL4)
DTF Station Prestige R2 Pro
DTF Station Prestige R1
DTF Station Prestige R2 (original)
Prestige X6
DTF Station Prestige A4
DTF Station Prestige A3+ and A3+ R
DTF Station Aries 124 UV DTF printer
Miro DTF Powder Shakers: Miro 13 Max, 16, 24 and 36
DTF Station Aries 213 and Aries 113 UV DTF printers
Seismo L16R and L24R DTF Powder Shaker and Dryer
Phoenix Air 16x20 DTF Curing Oven
DTF Station Maxima and Proxima Dual Heat Presses
DTF Station Prisma Auto Heat Press
DTF Station Prisma Dual Heat Press
DTF Station Prisma Swing Heat Press
DTF Station Vega S17
DTF Station Prisma Sentry Heat Press
DTF Station Seismo V36R DTF Powder Shaker and Dryer
DTF Station Arc 127 automatic cutter for DTF and UV DTF film
Epson SureColor F2100
Epson SureColor G6070 DTF printer
Epson SureColor F2270
Epson SureColor F3070
Epson SureColor F570
Epson SureColor F170
Epson SureColor F6470 and F6470H
Epson SureColor F6370
Epson SureColor F7200
Epson SureColor P-Series photo printers (P700, P900, P6570, P8570)
Epson SureColor T-Series CAD and technical printers
Epson SureColor S-Series (S40600, S60600, S80600)
Summa F Series changing knives and modules: Change Tool, knife swaps, up position and depth calibration
On a Summa F Series, click Change Tool in Axis Control before touching any knife or module, make the swap, then click Online so the table detects it. With the ADC fitted, the down position is measured for you; set the up position about 4 to 5 mm above the material and run a depth test. Fine depth tweaks of 0.1 mm, up to 0.2 mm, can be made with quick depth adjust.
Every knife or module change on an F Series goes through Axis Control's Change Tool menu. Summa is blunt about why: if you swap a tool without it, the table does not register the change and the cutting surface can be irreversibly damaged on the next job.
The rule for any change
-
Click Change Tool
Motor power is cut and the table will not move while the Online button is showing. Do not push the carriage far from where it is.
-
Make the change
Swap the knife, tool or module (steps below).
-
Click Online
The table detects the change and asks you to calibrate a new tool. It refuses to use a newly detected tool until you do.
Modules
- Installing: with no tool in the module, line it up with the carriage, slide it down the dovetail about 15 mm without forcing it, check the connector is fully seated, and tighten the screw on the right side.
- Removing: loosen the right-side screw about one turn, put the hex screwdriver in the hole under the module, lever it up 3 to 4 mm, then lift it out by hand. The drag module has no lever hole; lift it by hand.
- Good habits: label your modules and keep each in the same slot, since some tool settings are partly module-specific. Take off modules you are not using; Summa says leaving them on can lower cut quality. The drag module always goes in slot 1.
Changing knives
| Tool | Summa's steps |
|---|---|
| Drag knife | Loosen the screw and pull the tool. Turn the wheel clockwise to the end, take out the knife and the safety cap. Seat the new knife dull end first, then turn the screw until the tip just shows. Refit and tighten. |
| Kiss-cut knife | Hold the module button and turn the wheel to release the tool. Unscrew the end, push the knife out, fit the new one flat side to flat side with the knife pusher. Screw back until the tip shows, refit with the pin in the slot and tighten. |
| Single or double edge | Push the button, turn the wheel and remove the tool. Hold the gliding disk, loosen its screw and take it off. Loosen the two screws halfway, swap the blade pushed fully home, tighten. Refit the disk with its slot on the pin, then refit the tool until tight. |
Calibrate after the change
- Down position: on tables with the ADC (automatic depth control), the down position of every tool except the drag knife is measured automatically at start-up and after each tool change.
- Up position: set this yourself. In the module menu choose Up position (or Up on the remote) and bring the tip to about 4 to 5 mm above the material, or 4 to 5 mm above the known material thickness. Apply.
- Origin, lateral and longitudinal: the ADC can measure these too. Summa says to do it on a tool's first install or when cut quality is off.
- Depth test: put the media a few cm left of the machine origin and set the origin 1 to 2 cm inside it, then run a depth test and adjust. Softer media needs a slightly deeper setting.
- Kiss-cut depth: start with the knife flush with the nose piece bearings. Each quarter turn of the holder adds about 0.12 mm.
- Drag knife: set speed, pressure and offset, then test. The right pressure cuts the vinyl and only scratches the backing.
For small depth corrections, such as a knife wearing down, use quick depth adjust in the Modules menu: 0.1 mm per click, up to 0.2 mm in total. Bigger changes need the full depth procedure. Questions on a tool not listed here? Text us at (562) 609-4996.
Watch Summa's video: how to replace a drag knife on the F Series
More videos
Embedded from the manufacturer's official channel.
Common questions
What happens if I skip Change Tool?
Summa warns the table will not detect the change, and the cutting surface may be irreversibly damaged on the next job.
Does the ADC measure the drag knife?
No. It measures every tool except the drag knife.
How high should the up position be?
About 4 to 5 mm above the material, so the tool clears it when moving.
Should I leave spare modules on the carriage?
No. Summa recommends removing unused modules because they can lower cut quality.











































































