Machine type
Prestige XL series (L2, XL2, XL2 Pro, XL3, XL4)
DTF Station Prestige R2 Pro
DTF Station Prestige R1
DTF Station Prestige R2 (original)
Prestige X6
DTF Station Prestige A4
DTF Station Prestige A3+ and A3+ R
Epson SureColor G6070 DTF printer
Mimaki TxF300-1600
Mimaki TxF330-800
STS XPD-924D DTF Printer (Mutoh)
STS VJ-628D DTF Printer (Mutoh)
DTF Station Vega S17
STS XpertJet 1682D (XPJ-1682D) 64 inch DTF Printer
STS XPD-724 DTF Printer (Mutoh)
Hotronix Fusion IQ, Air Fusion IQ and Dual Air Fusion IQ
Geo Knight DK20S and DK20SP Digital Knight Swing-Away Presses
DTF Station Maxima and Proxima Dual Heat Presses
Hotronix Auto Open Clam and Hover Heat Press
DTF Station Prisma Auto Heat Press
DTF Station Prisma Dual Heat Press
DTF Station Prisma Swing Heat Press
Insta 718, 728 and 828 Automatic Swing-Away Heat Presses
DTF Station Prisma Sentry Heat Press
Geo Knight DC16 and DC16AP Digital Combo Swing-Away Presses
Geo Knight DK Digital Clamshell Presses: DK20, DK16, DKA Auto, DK8 Label and DK7 Cap
Hotronix Auto Open Cap Press and 360 IQ Hat Press
Hotronix Craft Heat Press 9 x 12
Hotronix Mighty Mug Heat Press
Insta 256 and 288 Manual Swing-Away Heat Presses
Insta 907 Dual Station Shuttle Label Heat Press
Viper MAXX pretreatment machine
Ecofreen Mister-T2 and Mister-T2 Pro pretreatment machines
Pearl Elite and Pearl PTM DTG pretreatment machines
Viper XPT-1000 pretreatment machine
Lawson Silver-Jet and Silver-Jet V2 DTG Pretreat Sprayers
Lawson Zoom-AE DTG pretreatment machine
Viper MINI handheld DTG pretreatment machine
Brand
Prestige XL series (L2, XL2, XL2 Pro, XL3, XL4)
DTF Station Prestige R2 Pro
DTF Station Prestige R1
DTF Station Prestige R2 (original)
Prestige X6
DTF Station Prestige A4
DTF Station Prestige A3+ and A3+ R
DTF Station Aries 124 UV DTF printer
Miro DTF Powder Shakers: Miro 13 Max, 16, 24 and 36
DTF Station Aries 213 and Aries 113 UV DTF printers
Seismo L16R and L24R DTF Powder Shaker and Dryer
Phoenix Air 16x20 DTF Curing Oven
DTF Station Maxima and Proxima Dual Heat Presses
DTF Station Prisma Auto Heat Press
DTF Station Prisma Dual Heat Press
DTF Station Prisma Swing Heat Press
DTF Station Vega S17
DTF Station Prisma Sentry Heat Press
DTF Station Seismo V36R DTF Powder Shaker and Dryer
DTF Station Arc 127 automatic cutter for DTF and UV DTF film
Epson SureColor F2100
Epson SureColor G6070 DTF printer
Epson SureColor F2270
Epson SureColor F3070
Epson SureColor F570
Epson SureColor F170
Epson SureColor F6470 and F6470H
Epson SureColor F6370
Epson SureColor F7200
Epson SureColor P-Series photo printers (P700, P900, P6570, P8570)
Epson SureColor T-Series CAD and technical printers
Epson SureColor S-Series (S40600, S60600, S80600)
Summa F Series maintenance: daily checks, nose piece and gliding disk, conveyor, ADC lens and rails
Each day, move the Summa F Series conveyor about 1 m by hand before start-up, clear dust and scraps, and test the light beam and emergency stops. Weekly, inspect everything and clean the kiss-cut nose piece, gliding disks, conveyor, side brushes and ADC lens as needed. Service maintenance flagged by Axis Control is done by a Summa-trained technician.
The F Series has very little the owner needs to lubricate, but dust, vinyl residue and lint build up fast and show up as bad cuts or weak vacuum. Summa splits owner maintenance into daily and weekly or monthly jobs. Deeper service, which Axis Control prompts for after a set number of operating hours, is for a Summa-trained technician.
Switch the table off before inspecting or cleaning it, unless a step says otherwise. Keep hands, hair, sleeves and jewelry clear of moving parts.
Every day
-
Advance the conveyor
Before you start the machine, move the conveyor forward by hand about 1 m.
-
Clear the table
Remove dust and leftover bits of cut material.
-
Test the safety devices
Check the light beam and the emergency stops work.
Weekly, or when cut quality drops
Summa recommends a full visual inspection at least once a week. Use the Change Tool menu, or switch the table off, before removing any tool.
| Job | How |
|---|---|
| Kiss-cut nose piece | Remove the tool, note the nose piece orientation, push it out and pick off vinyl residue with a brush or tweezers. A cut line that breaks every 12 mm (0.5 in) is the classic sign. |
| Gliding disk (cutout, EOT) | Remove the tool and clear residue with a brush, tweezers or compressed air. A dry Teflon spray on the gliding surface is allowed. |
| Conveyor belt or mat | Set the vacuum pump to blow and vacuum the belt with a vacuum cleaner. A dusty belt loses vacuum. |
| Side brushes | Vacuum them. Do not use compressed air, which blows dust inside. |
| Guide rails | Only if very dirty: wipe with a lint-free rag, then go over them with a rag soaked in bearing or rail lubricant. |
| ADC lens | A puff of air, or a lint-free cloth with warm water. For heavy dirt, mild soapy water on a microfiber cloth, then dry without pressing. The lens scratches easily. |
| Compressed air filter (no POT) | Check and empty it. It sits behind the front cover (two screws). |
| POT oil (POT tables) | Check monthly and top up when below half. |
| Router collet | Every bit change: tap it clean or blow out the grooves and threads. |
General cleaning and knives
- Use a dust cover when the table is not in use.
- Wipe surfaces with a soft cloth dampened with isopropyl alcohol or mild detergent. No abrasives.
- Check knives regularly and replace any with a worn or broken tip.
- On EOT tools, the knife guide is the only part the owner replaces. Other worn EOT parts go to a Summa service center.
Router warning from Summa: a collet clogged with dust cannot grip the bit tightly. A bit that comes loose during routing damages the mat and the miller and can injure someone. Never close a collet without a bit or dummy bit in it.
When Axis Control shows the service maintenance message, contact us to book a Summa-trained technician. Skipping it can shorten the table's life and lower cut quality.
Common questions
My kiss cut has a gap every half inch. Why?
Summa says that is the typical sign of a dirty nose piece. Remove it and clean off the vinyl residue.
How do I clean the conveyor?
Set the vacuum pump to blow and vacuum the belt with a vacuum cleaner.
Can I blow out the side brushes with compressed air?
No. Vacuum them; compressed air pushes dust into the machine.
Do I need to grease the rails?
Normally no. The carriages are self-lubricating. Only very dirty rails get cleaned and wiped with rail lubricant.











































































