Machine type
Prestige XL series (L2, XL2, XL2 Pro, XL3, XL4)
DTF Station Prestige R2 Pro
DTF Station Prestige R1
DTF Station Prestige R2 (original)
Prestige X6
DTF Station Prestige A4
DTF Station Prestige A3+ and A3+ R
Epson SureColor G6070 DTF printer
Mimaki TxF300-1600
Mimaki TxF330-800
STS XPD-924D DTF Printer (Mutoh)
STS VJ-628D DTF Printer (Mutoh)
DTF Station Vega S17
STS XpertJet 1682D (XPJ-1682D) 64 inch DTF Printer
STS XPD-724 DTF Printer (Mutoh)
Hotronix Fusion IQ, Air Fusion IQ and Dual Air Fusion IQ
Geo Knight DK20S and DK20SP Digital Knight Swing-Away Presses
DTF Station Maxima and Proxima Dual Heat Presses
Hotronix Auto Open Clam and Hover Heat Press
DTF Station Prisma Auto Heat Press
DTF Station Prisma Dual Heat Press
DTF Station Prisma Swing Heat Press
Insta 718, 728 and 828 Automatic Swing-Away Heat Presses
DTF Station Prisma Sentry Heat Press
Geo Knight DC16 and DC16AP Digital Combo Swing-Away Presses
Geo Knight DK Digital Clamshell Presses: DK20, DK16, DKA Auto, DK8 Label and DK7 Cap
Hotronix Auto Open Cap Press and 360 IQ Hat Press
Hotronix Craft Heat Press 9 x 12
Hotronix Mighty Mug Heat Press
Insta 256 and 288 Manual Swing-Away Heat Presses
Insta 907 Dual Station Shuttle Label Heat Press
Viper MAXX pretreatment machine
Ecofreen Mister-T2 and Mister-T2 Pro pretreatment machines
Pearl Elite and Pearl PTM DTG pretreatment machines
Viper XPT-1000 pretreatment machine
Lawson Silver-Jet and Silver-Jet V2 DTG Pretreat Sprayers
Lawson Zoom-AE DTG pretreatment machine
Viper MINI handheld DTG pretreatment machine
Brand
Prestige XL series (L2, XL2, XL2 Pro, XL3, XL4)
DTF Station Prestige R2 Pro
DTF Station Prestige R1
DTF Station Prestige R2 (original)
Prestige X6
DTF Station Prestige A4
DTF Station Prestige A3+ and A3+ R
DTF Station Aries 124 UV DTF printer
Miro DTF Powder Shakers: Miro 13 Max, 16, 24 and 36
DTF Station Aries 213 and Aries 113 UV DTF printers
Seismo L16R and L24R DTF Powder Shaker and Dryer
Phoenix Air 16x20 DTF Curing Oven
DTF Station Maxima and Proxima Dual Heat Presses
DTF Station Prisma Auto Heat Press
DTF Station Prisma Dual Heat Press
DTF Station Prisma Swing Heat Press
DTF Station Vega S17
DTF Station Prisma Sentry Heat Press
DTF Station Seismo V36R DTF Powder Shaker and Dryer
DTF Station Arc 127 automatic cutter for DTF and UV DTF film
Epson SureColor F2100
Epson SureColor G6070 DTF printer
Epson SureColor F2270
Epson SureColor F3070
Epson SureColor F570
Epson SureColor F170
Epson SureColor F6470 and F6470H
Epson SureColor F6370
Epson SureColor F7200
Epson SureColor P-Series photo printers (P700, P900, P6570, P8570)
Epson SureColor T-Series CAD and technical printers
Epson SureColor S-Series (S40600, S60600, S80600)
Summa F Series loading media: sheets, rolls, origin, size and vacuum zones
Always load through Axis Control's Load menu so the Summa F Series cannot move while your hands are on the table. Choose Sheet or Roll, set a park position, place the media and test the vacuum, then set the origin and size. Set the width as close as possible to the real media edge, because the table uses that size to decide where to pull vacuum.
On the F Series, loading media means two things: putting it on the table safely and telling Axis Control where it is (the origin and size). The table uses that working area to decide where to pull vacuum, so a sloppy size setting shows up as media lifting and poor cuts.
Summa says to always load media through the Load menu. Only then is the table guaranteed not to make unexpected moves while your hands are on it.
Which vacuum system do you have?
All larger tables, and F1612 tables with model numbers ending -4X, use vacuum zones that switch on and off; Axis Control shows them as green lines and the origin can be at the lower right of any zone. Older F1612 tables (-1X, -2X, -3X) use a vacuum selector that adjusts width automatically; the origin must be at the lower right of the table. The model number is on the label just above the on/off switch.
Load a sheet
-
Open the load window
With the table started and Axis Control running, click Load and choose Sheet.
-
Pick the options
Choose a park position (where the carriage goes while you load) to suit loading from the front or rear. Tick Origin reset to go back to the mechanical origin, and tick Width to set the sheet width. Set the starting vacuum state.
-
Confirm and load
Click to start. The table sets the vacuum, parks the carriage and waits. Lay the sheet down and switch the vacuum on at least once to check it lies flat. Then click to finish; the carriage returns to the origin.
Load a roll
Summa recommends the conveyor, the pneumatic clamps and the roll support for roll media.
-
Start the roll load
Click Load and choose Roll. On the F1612, Summa suggests a park position of 850 to 1000 mm depending on the media's size and weight; on larger tables, 0 to 200 mm less than the maximum cutting length.
-
Fit the core holders
Loosen each core holder with its black knob, push one into each end of the roll and tighten both.
-
Set the roll on the supports
From the back of the machine, lay the roll on the supply rollers with the flanges sitting in the grooves of the flange guides.
-
Set the clamps and feed the media
Space the media advance clamps evenly, with the outer two about 10 cm from the edges. Slide the media forward until it sits under the clamps, as square to the side as you can. Heavy media goes a bit further. Use the remote to hold it with vacuum and work the clamps.
-
Finish
Click to finish. The table pulls the media forward as far as it can, sets the length to maximum, and returns to the media menu.
Keep the clamps away from the edges and from each other so they do not pinch the compressed air hoses.
Set the origin and size
-
Origin
In the media menu, change the origin by typing X and Y values or moving the carriage with the arrows or the remote. The red pointer marks the origin on the table, and the camera view can show it on screen. Confirm it, push it to the front, or cut the media off at that line.
-
Size
Set width and length the same way. Summa's tip: set the Y size as close to the real edge of the media as you can, so the vacuum holds properly.
If the media still slides or lifts, the conveyor may be clogged with dust (see our F Series cleaning guide). Let new media sit in the room before you cut, since it can have tighter limits than the table itself. For help, text us at (562) 609-4996.
Watch Summa's video: F1612 continuous sheet feed
More videos
Embedded from the manufacturer's official channel.
Common questions
How do I know if my F1612 has vacuum zones?
Zone tables show green lines in Axis Control when setting the origin and have a model number ending -4X. Older -1X, -2X and -3X tables use a vacuum selector.
Where should the clamps go for a roll?
Evenly across the media, with the outer two about 10 cm from the sides, and not so close that they pinch the air hoses.
My media lifts during cutting.
Re-set the size tightly to the media edge and check the conveyor is not clogged with dust.
Can I set the origin with the remote?
Yes, there is a quicker remote-only method, with fewer options.











































































