Support
Machine type
Brand
Summa F Series flatbed cutters (F1612, F1432, F1832, F3220, F3232)

Summa F Series start-up and stops: Axis Control order, status colors, light barrier and emergency stops

✓ Reviewed by Jason KimUpdated 2 min readFits: F1612 · F1432 · F1832 · F3220 · F3232
Short answer

Start Axis Control before powering on the Summa F Series, then confirm the start-up prompt so the table can test its emergency stops, bumpers and light beams. A broken light beam is a controlled stop you can continue with OK; an emergency stop kills the job and is released by turning it clockwise. Red in Axis Control means an error to acknowledge, blue means it is waiting on you.

The F Series is built so it cannot move by surprise. That also means it will sit still, or stop mid-job, whenever its safety checks are not happy. Most "it won't start" and "it stopped" calls come back to the start-up order or a safety device.

Start-up in the right order

  1. Open Axis Control first

    Summa's rule: start Axis Control before you switch the table on or connect the remote, and close Axis Control last.

  2. Power on and confirm

    Turn the power switch. Shortly after, Axis Control asks for permission to start the start-up sequence. Confirm it. The table will not move until you do.

  3. Let it check itself

    The table tests the emergency stops, then the trip switches in the bumpers, then the light beams. If an emergency stop is still pressed, the check stops there.

Read the status colors

Color Meaning
Green Normal: cutting or waiting for a job
Blue Paused or interrupted; you need to act
Yellow Warning message waiting for your OK
Red Error to confirm: e-stop, safety system, fatal error or rebooting
White Not ready: offline or updating firmware

The left side of the main window also shows USB (green connected, red not), remote, emergency stop, safety beam and fatal error status. The Axis Control icon in the system tray is white when normal, yellow when busy, and red when it has lost the connection to the table. The Events menu lists every message the table has sent, so check it first when something stopped.

Why it stopped

  • Light barrier or bumper: someone or something broke the beam along the top beam or pushed a bumper. This is a controlled stop: the table holds its position and the job can continue. Click OK in the Axis Control message to carry on.
  • Emergency stop: pressing any of the four corner buttons cuts motor power instantly and the current job is lost. Turn the button clockwise to release it.
  • Overcurrent: if the motors draw too much current, power to them is cut and Axis Control shows a fatal error. Clear anything blocking the carriage, then contact us before you run again.
  • No connection (red icon or red USB): check the USB cable runs straight from the table to the PC, with no hub, and is no longer than about 3 m. The camera needs USB 2.0 or better.

Do not use the emergency stop as a pause button. Summa warns it lowers cut quality. Use Pause in Axis Control: the table finishes the vectors already in its buffer at the right speed, then stops.

Pause, stop, reset and reboot

  • Pause (job sent from GoProduce): the table finishes what is buffered, then waits. Resume continues the job; Abort sends the carriage back to the origin.
  • Stop: finishes the buffered vectors, then resets the origin. The rest of the job is not cut.
  • Reset: stops the current job and resets the origin of the loaded media.
  • Reboot: a warm restart that runs the full initialization again. It does not restart the camera.

If it keeps stopping with no obvious cause, or a fatal error comes back, send us a screenshot of the Events list or text us at (562) 609-4996.

Watch Summa's video: long jobs on the F Series

Embedded from the manufacturer's official channel.

Common questions

The table is on but won't move. Why?

It waits for you to confirm the start-up sequence in Axis Control, and it will not pass the self-test with an emergency stop pressed.

Can I resume after the light barrier stops it?

Yes. It is a controlled stop that holds position. Click OK in the Axis Control message.

Can I resume after an emergency stop?

No. Motor power is cut instantly and the job is lost. Release the button (turn it clockwise) and resend.

The Axis Control icon is red.

Axis Control has lost the connection. Check the direct USB cable, no hub, about 3 m maximum.

Did this fix it?