Machine type
Prestige XL series (L2, XL2, XL2 Pro, XL3, XL4)
DTF Station Prestige R2 Pro
DTF Station Prestige R1
DTF Station Prestige R2 (original)
Prestige X6
DTF Station Prestige A4
DTF Station Prestige A3+ and A3+ R
Epson SureColor G6070 DTF printer
Mimaki TxF300-1600
Mimaki TxF330-800
STS XPD-924D DTF Printer (Mutoh)
STS VJ-628D DTF Printer (Mutoh)
DTF Station Vega S17
STS XpertJet 1682D (XPJ-1682D) 64 inch DTF Printer
STS XPD-724 DTF Printer (Mutoh)
Hotronix Fusion IQ, Air Fusion IQ and Dual Air Fusion IQ
Geo Knight DK20S and DK20SP Digital Knight Swing-Away Presses
DTF Station Maxima and Proxima Dual Heat Presses
Hotronix Auto Open Clam and Hover Heat Press
DTF Station Prisma Auto Heat Press
DTF Station Prisma Dual Heat Press
DTF Station Prisma Swing Heat Press
Insta 718, 728 and 828 Automatic Swing-Away Heat Presses
DTF Station Prisma Sentry Heat Press
Geo Knight DC16 and DC16AP Digital Combo Swing-Away Presses
Geo Knight DK Digital Clamshell Presses: DK20, DK16, DKA Auto, DK8 Label and DK7 Cap
Hotronix Auto Open Cap Press and 360 IQ Hat Press
Hotronix Craft Heat Press 9 x 12
Hotronix Mighty Mug Heat Press
Insta 256 and 288 Manual Swing-Away Heat Presses
Insta 907 Dual Station Shuttle Label Heat Press
Viper MAXX pretreatment machine
Ecofreen Mister-T2 and Mister-T2 Pro pretreatment machines
Pearl Elite and Pearl PTM DTG pretreatment machines
Viper XPT-1000 pretreatment machine
Lawson Silver-Jet and Silver-Jet V2 DTG Pretreat Sprayers
Lawson Zoom-AE DTG pretreatment machine
Viper MINI handheld DTG pretreatment machine
Brand
Prestige XL series (L2, XL2, XL2 Pro, XL3, XL4)
DTF Station Prestige R2 Pro
DTF Station Prestige R1
DTF Station Prestige R2 (original)
Prestige X6
DTF Station Prestige A4
DTF Station Prestige A3+ and A3+ R
DTF Station Aries 124 UV DTF printer
Miro DTF Powder Shakers: Miro 13 Max, 16, 24 and 36
DTF Station Aries 213 and Aries 113 UV DTF printers
Seismo L16R and L24R DTF Powder Shaker and Dryer
Phoenix Air 16x20 DTF Curing Oven
DTF Station Maxima and Proxima Dual Heat Presses
DTF Station Prisma Auto Heat Press
DTF Station Prisma Dual Heat Press
DTF Station Prisma Swing Heat Press
DTF Station Vega S17
DTF Station Prisma Sentry Heat Press
DTF Station Seismo V36R DTF Powder Shaker and Dryer
DTF Station Arc 127 automatic cutter for DTF and UV DTF film
Epson SureColor F2100
Epson SureColor G6070 DTF printer
Epson SureColor F2270
Epson SureColor F3070
Epson SureColor F570
Epson SureColor F170
Epson SureColor F6470 and F6470H
Epson SureColor F6370
Epson SureColor F7200
Epson SureColor P-Series photo printers (P700, P900, P6570, P8570)
Epson SureColor T-Series CAD and technical printers
Epson SureColor S-Series (S40600, S60600, S80600)
xTool F1 Ultra auto-focus failed or thickness wrong: red and blue dot calibration
xTool treats an auto-focus reading within 0.5 mm of the real thickness as normal. If it fails or is further off, put the material under the blue spot, use manual focus on clear, shiny, fluffy or black materials, keep the connection steady and don't touch the controller while it measures. If the spots overlap but the thickness is still wrong, run Z-axis homing, then xTool's Fiber IR and blue-light laser calibration with the included scratch paper.
Match your symptom
| What you see | Likely cause | Go to |
|---|---|---|
| "Auto-focus failed" pop-up | Material placement, material type or connection | Steps 1 to 4 |
| Spots overlap but thickness is off | Z-axis needs homing | Step 5 |
| Off by more than 0.5 mm every time | Calibration has drifted | Step 6 |
| Job lands in the wrong place | Calibration has drifted | Step 6 |
Step by step
-
Hands off during the measurement
The measurement stops if you press any controller button or click Reset in Device settings while it runs. Start it, then wait.
-
Put the material under the blue spot
Auto-focus measures where the blue spot falls. If the material is beside it, the reading fails or comes out wrong. Close the enclosure while it measures so room light doesn't interfere.
-
Check the material
Clear, see-through, shiny, fluffy and very dark materials don't work with auto-focus. Lay a thin opaque sheet on top to help it measure, or focus by hand: hold Up/Down until the red and blue spots overlap.
-
Steady connection
The machine sends camera images to xTool's software to work out the distance. A dropped or slow Wi-Fi link can make it fail. Try the USB cable.
-
Run Z-axis homing
If the spots overlap but the thickness is wrong, open Device settings and click Homing under Z-axis homing. The laser module goes back to its start position. Measure again.
-
Run the Fiber IR and blue-light laser calibration
xTool publishes this one for owners. You need the 100 x 100 mm art scratch paper from the box and some tape. Update the firmware first so you get the Auto-recognize button.
- Open Device settings > Parameter settings and click Start calibration next to Fiber IR and blue-light laser calibration.
- Tape the paper flat, as close to the center of the baseplate as you can.
- If the camera image is blurry, close the enclosure, click refresh, or raise the fill light brightness in Device settings.
- Click Auto-recognize. If you enter values by hand, read them from the center of the engraved cross (not the dots), keep X (horizontal) and Y (vertical) straight, get the plus or minus sign right, and work to 0.1 mm.
- Click Recheck, then Confirm.
- When it asks you to adjust the red dot, tighten the screw on the right of the ball head gently. Overtightening moves the dot again.
- Screenshot the final numbers for next time.
If the machine falls asleep partway through, wake it by touching the screen. Don't press the controller buttons; xTool warns this can spoil the calibration.
Still not right?
Use manual focus to keep working, and contact us. It helps to have your firmware version (Device settings > Basic info), the serial number from the back of the machine near the smoke outlet, and a short video of the auto-focus attempt. Text it to (562) 609-4996.
Watch xTool's video: calibrating the F1 Ultra
More videos
Embedded from the manufacturer's official channel.
Common questions
How accurate should auto-focus be?
xTool says a measured thickness within 0.5 mm of the real thickness is normal. More than that means the machine needs calibrating.
Why does auto-focus fail on clear acrylic and glass?
Auto-focus reads light bouncing back from the surface. Clear, see-through, mirror-like, fluffy (cotton) and light-absorbing (black acrylic) materials don't give it a clean reading. Lay a thin opaque sheet over the surface, or focus by hand with the buttons.
Can I just focus by hand?
Yes. Hold Up/Down on the controller until the red and blue spots overlap on the material. xTool recommends this as the fallback, and it is the only option for offline jobs.
Why did my laser go out of calibration?
xTool says long shipping and moves can shift it, which is why the calibration exists. Keep the original foam and boxes: xTool says the inside must be packed with the accessory foam boxes when you move it, or the laser module can shift.
The calibration screen looks different from the pictures.
Auto-recognize only appears on recent firmware. Update the firmware first, then run the calibration again.
- F1 Ultra Auto Focus Issue
- Focus the Laser (F1 Ultra)
- Perform Infrared and Blue-Light Laser Calibrate for xTool F1 Ultra
- Enhance Success in Second Calibration of F1 Ultra's Blue and Red Dots
- xTool F1 Ultra Q&A
- xTool F1 Ultra Unboxing and First Use
- Upgrade the Firmware for xTool F1 Ultra
- AA support requests about xTool lasers, 2024 to 2026











































































