Machine type
Prestige XL series (L2, XL2, XL2 Pro, XL3, XL4)
DTF Station Prestige R2 Pro
DTF Station Prestige R1
DTF Station Prestige R2 (original)
Prestige X6
DTF Station Prestige A4
DTF Station Prestige A3+ and A3+ R
Epson SureColor G6070 DTF printer
Mimaki TxF300-1600
Mimaki TxF330-800
STS XPD-924D DTF Printer (Mutoh)
STS VJ-628D DTF Printer (Mutoh)
DTF Station Vega S17
STS XpertJet 1682D (XPJ-1682D) 64 inch DTF Printer
STS XPD-724 DTF Printer (Mutoh)
Hotronix Fusion IQ, Air Fusion IQ and Dual Air Fusion IQ
Geo Knight DK20S and DK20SP Digital Knight Swing-Away Presses
DTF Station Maxima and Proxima Dual Heat Presses
Hotronix Auto Open Clam and Hover Heat Press
DTF Station Prisma Auto Heat Press
DTF Station Prisma Dual Heat Press
DTF Station Prisma Swing Heat Press
Insta 718, 728 and 828 Automatic Swing-Away Heat Presses
DTF Station Prisma Sentry Heat Press
Geo Knight DC16 and DC16AP Digital Combo Swing-Away Presses
Geo Knight DK Digital Clamshell Presses: DK20, DK16, DKA Auto, DK8 Label and DK7 Cap
Hotronix Auto Open Cap Press and 360 IQ Hat Press
Hotronix Craft Heat Press 9 x 12
Hotronix Mighty Mug Heat Press
Insta 256 and 288 Manual Swing-Away Heat Presses
Insta 907 Dual Station Shuttle Label Heat Press
Viper MAXX pretreatment machine
Ecofreen Mister-T2 and Mister-T2 Pro pretreatment machines
Pearl Elite and Pearl PTM DTG pretreatment machines
Viper XPT-1000 pretreatment machine
Lawson Silver-Jet and Silver-Jet V2 DTG Pretreat Sprayers
Lawson Zoom-AE DTG pretreatment machine
Viper MINI handheld DTG pretreatment machine
Brand
Prestige XL series (L2, XL2, XL2 Pro, XL3, XL4)
DTF Station Prestige R2 Pro
DTF Station Prestige R1
DTF Station Prestige R2 (original)
Prestige X6
DTF Station Prestige A4
DTF Station Prestige A3+ and A3+ R
DTF Station Aries 124 UV DTF printer
Miro DTF Powder Shakers: Miro 13 Max, 16, 24 and 36
DTF Station Aries 213 and Aries 113 UV DTF printers
Seismo L16R and L24R DTF Powder Shaker and Dryer
Phoenix Air 16x20 DTF Curing Oven
DTF Station Maxima and Proxima Dual Heat Presses
DTF Station Prisma Auto Heat Press
DTF Station Prisma Dual Heat Press
DTF Station Prisma Swing Heat Press
DTF Station Vega S17
DTF Station Prisma Sentry Heat Press
DTF Station Seismo V36R DTF Powder Shaker and Dryer
DTF Station Arc 127 automatic cutter for DTF and UV DTF film
Epson SureColor F2100
Epson SureColor G6070 DTF printer
Epson SureColor F2270
Epson SureColor F3070
Epson SureColor F570
Epson SureColor F170
Epson SureColor F6470 and F6470H
Epson SureColor F6370
Epson SureColor F7200
Epson SureColor P-Series photo printers (P700, P900, P6570, P8570)
Epson SureColor T-Series CAD and technical printers
Epson SureColor S-Series (S40600, S60600, S80600)
xTool F1 Ultra first job: choosing the laser, focusing, framing and offline jobs
On the F1 Ultra, use the blue diode laser for wood, leather, paper and acrylic, and the fiber infrared laser for metals. Focus by holding the Up/Down button on the touchscreen controller until the red and blue light spots overlap on the material, then frame the design before you start. Close the enclosure, click Start in xTool Studio, and press the controller's Start/Stop button when the software says Ready.
Before the first job
Remove the field lens protector, insert the key, make sure the emergency stop is released (twist it), connect the touchscreen controller with the notch facing up, fit the exhaust pipe and power on. Connect xTool Studio over the USB cable first. Our guide on installing xTool Studio and connecting over USB, Wi-Fi or IP covers that part.
Never use the emergency stop as an on/off switch. xTool warns that it can damage the machine. Use the power switch.
Choose the laser for the material
| Laser | Use it for |
|---|---|
| Blue diode | Wood, corrugated paper, leather, acrylic, and most cutting jobs |
| Fiber infrared | Metals: stainless steel, aluminum, copper, brass, gold, silver |
| Either | Stainless steel, photo paper and rock coasters mark with both, with a slightly different look |
In xTool Studio, pick the material from the list and the software fills in xTool's recommended laser and settings. Those numbers are tuned for xTool's own materials, so test anything else on scrap first.
Run the job
-
Pick the mode and material
On the right panel, choose Process on flat surface, click Unknown Material, choose your material and click Apply.
-
Place the material
Lift the enclosure and set the material so the blue light spot lands on it. For cutting, put the slatted panel underneath to protect the baseplate and reduce burn marks on the back. Tape down light pieces, because the exhaust airflow can move them.
-
Focus
Hold the Up/Down button on the controller. The blue spot stays put; the red spot moves left as the module goes up and right as it goes down. When the two spots overlap, you are in focus and Studio shows the measured thickness. Auto-focus (the Auto-measure icon in the software) also works on most opaque materials, with the enclosure closed.
-
Take a background photo and place the design
Focus first, then click Refresh background so the camera image lines up. Place your design inside the material on the canvas.
-
Set every object
Select each object and set its processing type and settings. An object with no settings may be skipped. For heavy-smoke scoring on wood or cardboard, turn on Evade smoke in the path settings.
-
Frame it
Click Framing. The laser dot traces the border (Rect) or the outline (Outline) on the material. Move the design in the software if it is off, and frame again.
-
Start
Click Process, preview the path, close the enclosure, click Start, and press the XTOOL Start/Stop button on the controller when the software shows Ready.
Keep the enclosure closed while the laser runs. If a job needs it open, xTool says to wear goggles rated for both 455 nm and 1064 nm, and never leave a running job unattended.
Controller buttons worth knowing
- Start/Stop: press once to start or pause, twice quickly to repeat the last job, hold 2 seconds to stop and cancel, hold 5 seconds to switch the connection mode (the machine beeps and shows the AP hotspot icon).
- Framing: press once to start or stop framing.
- Up/Down: raises or lowers the laser module for manual focus.
Jobs without a computer
-
Export the file
In xTool Studio, open Device settings and click Export next to Export .xf file, saving it to a USB flash drive. After an online job you can also click Back up file to device on the Complete page. The first time you power on, a sample file called "Cat" is already on the machine.
-
Open it on the touchscreen
Plug the drive into the machine, tap the USB icon and tap the file, then tap Process.
-
Focus by hand, frame, and run
Offline jobs only support manual focus. Frame with the controller's Framing button, close the enclosure, then double press Start/Stop to begin.
If the spots will not line up or the job lands in the wrong place, see our guide on F1 Ultra auto-focus and red and blue dot calibration, or text us a short video at (562) 609-4996.
Watch xTool's video: using the F1 Ultra with proper laser focus
More videos
Embedded from the manufacturer's official channel.
Common questions
Which laser do I pick, blue or fiber?
xTool's rule of thumb is fiber infrared for metals such as stainless steel, aluminum, copper, gold and silver, and the blue diode for wood, corrugated paper, leather and acrylic, and for cutting. Some materials, such as stainless steel and rock coasters, take both, with a different look.
Which way do I move the laser module to focus?
The blue spot stays still. Moving the module up sends the red spot to the left, and moving it down sends it to the right. Stop when the two spots sit on top of each other.
Can I use auto-focus instead?
Yes, but only while connected to xTool's software, and not on clear, see-through, shiny, fluffy or very dark materials such as black acrylic. Use the buttons for those.
I can barely see the framing light. Is something wrong?
No. Framing uses the blue laser at very low power, and the enclosure lid filters it. xTool says you can raise the framing power next to the Framing button, and lay white paper on shiny metal to see the outline better.
Can I run a job without a computer?
Yes. Export the project as an .xf file to a USB flash drive, plug it into the machine, open it on the touchscreen, focus by hand, frame, close the enclosure and double press Start/Stop. Offline jobs only support manual focus.
- xTool F1 Ultra User Guide
- The Touchscreen Controller
- Focus the Laser (F1 Ultra)
- (xTool Studio) How to Process on Flat Surface with xTool F1 Ultra
- (xTool Studio) Start Offline Processing with the Touchscreen Controller
- The Processing Parameters for xTool F1 Ultra
- xTool F1 Ultra Q&A
- Connect and Set up xTool F1 Ultra via xTool Studio











































































