Machine type
Prestige XL series (L2, XL2, XL2 Pro, XL3, XL4)
DTF Station Prestige R2 Pro
DTF Station Prestige R1
DTF Station Prestige R2 (original)
Prestige X6
DTF Station Prestige A4
DTF Station Prestige A3+ and A3+ R
Epson SureColor G6070 DTF printer
Mimaki TxF300-1600
Mimaki TxF330-800
STS XPD-924D DTF Printer (Mutoh)
STS VJ-628D DTF Printer (Mutoh)
DTF Station Vega S17
STS XpertJet 1682D (XPJ-1682D) 64 inch DTF Printer
STS XPD-724 DTF Printer (Mutoh)
Hotronix Fusion IQ, Air Fusion IQ and Dual Air Fusion IQ
Geo Knight DK20S and DK20SP Digital Knight Swing-Away Presses
DTF Station Maxima and Proxima Dual Heat Presses
Hotronix Auto Open Clam and Hover Heat Press
DTF Station Prisma Auto Heat Press
DTF Station Prisma Dual Heat Press
DTF Station Prisma Swing Heat Press
Insta 718, 728 and 828 Automatic Swing-Away Heat Presses
DTF Station Prisma Sentry Heat Press
Geo Knight DC16 and DC16AP Digital Combo Swing-Away Presses
Geo Knight DK Digital Clamshell Presses: DK20, DK16, DKA Auto, DK8 Label and DK7 Cap
Hotronix Auto Open Cap Press and 360 IQ Hat Press
Hotronix Craft Heat Press 9 x 12
Hotronix Mighty Mug Heat Press
Insta 256 and 288 Manual Swing-Away Heat Presses
Insta 907 Dual Station Shuttle Label Heat Press
Viper MAXX pretreatment machine
Ecofreen Mister-T2 and Mister-T2 Pro pretreatment machines
Pearl Elite and Pearl PTM DTG pretreatment machines
Viper XPT-1000 pretreatment machine
Lawson Silver-Jet and Silver-Jet V2 DTG Pretreat Sprayers
Lawson Zoom-AE DTG pretreatment machine
Viper MINI handheld DTG pretreatment machine
Brand
Prestige XL series (L2, XL2, XL2 Pro, XL3, XL4)
DTF Station Prestige R2 Pro
DTF Station Prestige R1
DTF Station Prestige R2 (original)
Prestige X6
DTF Station Prestige A4
DTF Station Prestige A3+ and A3+ R
DTF Station Aries 124 UV DTF printer
Miro DTF Powder Shakers: Miro 13 Max, 16, 24 and 36
DTF Station Aries 213 and Aries 113 UV DTF printers
Seismo L16R and L24R DTF Powder Shaker and Dryer
Phoenix Air 16x20 DTF Curing Oven
DTF Station Maxima and Proxima Dual Heat Presses
DTF Station Prisma Auto Heat Press
DTF Station Prisma Dual Heat Press
DTF Station Prisma Swing Heat Press
DTF Station Vega S17
DTF Station Prisma Sentry Heat Press
DTF Station Seismo V36R DTF Powder Shaker and Dryer
DTF Station Arc 127 automatic cutter for DTF and UV DTF film
Epson SureColor F2100
Epson SureColor G6070 DTF printer
Epson SureColor F2270
Epson SureColor F3070
Epson SureColor F570
Epson SureColor F170
Epson SureColor F6470 and F6470H
Epson SureColor F6370
Epson SureColor F7200
Epson SureColor P-Series photo printers (P700, P900, P6570, P8570)
Epson SureColor T-Series CAD and technical printers
Epson SureColor S-Series (S40600, S60600, S80600)
xTool Auto Streamline conveyor on the F1 Ultra and F2 Ultra UV: install, batch engraving and long materials
Fit the fastening pieces for your laser (A and B for the F1 Ultra, C and D for the F2 Ultra UV), secure the conveyor and connect its cable. In xTool Studio choose "Same design - batch processing" to engrave one design on many pieces, or "Use conveyor-large" for a long piece fed right to left. The conveyor engraves only, never cuts, and must not carry paper or cloth. Wear goggles because the enclosure can't close fully.
What the conveyor does
The Auto Streamline conveyor bolts to the front of the laser and feeds material through. It has two jobs: batch processing (the camera finds each piece you drop on the belt and engraves the same design on it) and large material (a long piece is fed through and engraved in sections). It engraves only. It does not support laser cutting.
The enclosure cannot close fully with the conveyor fitted. Wear goggles for every conveyor job: 455 nm and 1064 nm on the F1 Ultra, 355 nm (plus or minus 5 nm) on the F2 Ultra UV. Goggles are not included with the laser or the conveyor.
Install it
| Laser | On the conveyor | On the laser |
|---|---|---|
| F1 Ultra | Fastening piece B | Fastening piece A |
| F2 Ultra UV | Fastening piece D | Fastening piece C |
The box carries both kits. Fit the two fastening pieces, secure the conveyor to the laser, then join them with the connection cable. On the F2 Ultra UV, also connect the touchscreen controller and make sure the surface engraving lens is fitted: xTool says it cannot use the conveyor with the inner engraving lens. An older conveyor made only for the F1 Ultra has a different cable and fastening kit.
Batch: the same design on many pieces
-
Pick the mode and material
Connect the laser to xTool Studio by USB. Click the processing mode name and choose Same design - batch processing. Click Unknown Material, choose your material and click Apply. xTool's defaults are tuned for xTool materials, so test anything else first.
-
Focus on the first piece
Lay one piece in the processing area so the blue dot falls on it. Hold the Up/Down button (on the laser module on the F1 Ultra, on the touchscreen controller on the F2 Ultra UV) until the red and blue dots overlap. The blue dot stays still and the red one moves.
-
Take the background and design
Click Refresh background after focusing. If you get shadows or a blurry image, adjust the piece or the light, or pull the enclosure down, and refresh again. Create the design on the piece and set its parameters.
-
Frame the sample
Click Next, drag the box around the first piece (the sample) and click Process. xTool Studio then fills the same design onto matching pieces.
-
Start and keep feeding
Preview the path, put on goggles, click Start and press the XTOOL Start/Stop button when the software shows Ready. Add new pieces to the right of the processing area as it runs. On the F2 Ultra UV, keep the enclosure no more than 5 mm above the material.
-
Stopping
The batch ends by itself once no material is detected five times in a row. To stop sooner, click Cancel in xTool Studio or double-press the Start/Stop button.
Large material: one long piece
-
Choose the mode
Select Use conveyor-large and your material.
-
Place and focus
Put the material on the right side of the belt so the blue dot falls on it, and focus with the Up/Down button. The beam only lands on the middle line of the conveyor and the material moves right to left, so anything already left of that line will not be engraved. After focusing, slide the material back to the right of the middle line.
-
Design and run
Refresh the background, add your design, and keep it out of the gray area on the left of the canvas, which is not processed. Set parameters for every object, frame it, then process as above.
Rules that prevent most failures
- Never run paper, cloth or other thin material that light passes through. Beams that reach the belt damage it.
- Keep pieces away from the belt edges, and don't let them touch or overlap.
- Batch pieces should be the same material. Keep hands out of the processing area when you add pieces.
- Keep third-party material dry and clean; moisture and contamination change results.
If the conveyor isn't detected or a batch keeps skipping pieces, text us a short video at (562) 609-4996.
Watch xTool's unboxing of the Auto Streamline conveyor for the F2 Ultra and F1 Ultra
Embedded from the manufacturer's official channel.
Common questions
Can I cut with the conveyor?
No. xTool says the conveyor supports engraving only.
Why can't I run paper or fabric on it?
Thin material lets the beam through to the belt, and that damages the belt.
When does a batch stop?
Automatically, after no material is detected five times in a row. You can also click Cancel or double-press the Start/Stop button.
Part of my long piece didn't engrave. Why?
The beam only lands on the conveyor's middle line and the material moves right to left. Anything that started left of that line is skipped, so slide the piece right of the line after focusing.
My F2 Ultra UV won't run the conveyor.
Check that the surface engraving lens is fitted. It won't work with the inner engraving lens.
- xTool Auto Streamline Conveyor User Guide
- (xTool Studio) Use the Conveyor for Processing Same Designs in Batches (F1 Ultra)
- (xTool Studio) How to Use the Conveyor to Process a Large Material with xTool F1 Ultra
- (xTool Studio) Use the Conveyor for Batch Processing (Same Design) with xTool F2 Ultra UV
- (xTool Studio) Use the Conveyor to Process a Large Material with xTool F2 Ultra UV











































































