Machine type
Prestige XL series (L2, XL2, XL2 Pro, XL3, XL4)
DTF Station Prestige R2 Pro
DTF Station Prestige R1
DTF Station Prestige R2 (original)
Prestige X6
DTF Station Prestige A4
DTF Station Prestige A3+ and A3+ R
Epson SureColor G6070 DTF printer
Mimaki TxF300-1600
Mimaki TxF330-800
STS XPD-924D DTF Printer (Mutoh)
STS VJ-628D DTF Printer (Mutoh)
DTF Station Vega S17
STS XpertJet 1682D (XPJ-1682D) 64 inch DTF Printer
STS XPD-724 DTF Printer (Mutoh)
Hotronix Fusion IQ, Air Fusion IQ and Dual Air Fusion IQ
Geo Knight DK20S and DK20SP Digital Knight Swing-Away Presses
DTF Station Maxima and Proxima Dual Heat Presses
Hotronix Auto Open Clam and Hover Heat Press
DTF Station Prisma Auto Heat Press
DTF Station Prisma Dual Heat Press
DTF Station Prisma Swing Heat Press
Insta 718, 728 and 828 Automatic Swing-Away Heat Presses
DTF Station Prisma Sentry Heat Press
Geo Knight DC16 and DC16AP Digital Combo Swing-Away Presses
Geo Knight DK Digital Clamshell Presses: DK20, DK16, DKA Auto, DK8 Label and DK7 Cap
Hotronix Auto Open Cap Press and 360 IQ Hat Press
Hotronix Craft Heat Press 9 x 12
Hotronix Mighty Mug Heat Press
Insta 256 and 288 Manual Swing-Away Heat Presses
Insta 907 Dual Station Shuttle Label Heat Press
Viper MAXX pretreatment machine
Ecofreen Mister-T2 and Mister-T2 Pro pretreatment machines
Pearl Elite and Pearl PTM DTG pretreatment machines
Viper XPT-1000 pretreatment machine
Lawson Silver-Jet and Silver-Jet V2 DTG Pretreat Sprayers
Lawson Zoom-AE DTG pretreatment machine
Viper MINI handheld DTG pretreatment machine
Brand
Prestige XL series (L2, XL2, XL2 Pro, XL3, XL4)
DTF Station Prestige R2 Pro
DTF Station Prestige R1
DTF Station Prestige R2 (original)
Prestige X6
DTF Station Prestige A4
DTF Station Prestige A3+ and A3+ R
DTF Station Aries 124 UV DTF printer
Miro DTF Powder Shakers: Miro 13 Max, 16, 24 and 36
DTF Station Aries 213 and Aries 113 UV DTF printers
Seismo L16R and L24R DTF Powder Shaker and Dryer
Phoenix Air 16x20 DTF Curing Oven
DTF Station Maxima and Proxima Dual Heat Presses
DTF Station Prisma Auto Heat Press
DTF Station Prisma Dual Heat Press
DTF Station Prisma Swing Heat Press
DTF Station Vega S17
DTF Station Prisma Sentry Heat Press
DTF Station Seismo V36R DTF Powder Shaker and Dryer
DTF Station Arc 127 automatic cutter for DTF and UV DTF film
Epson SureColor F2100
Epson SureColor G6070 DTF printer
Epson SureColor F2270
Epson SureColor F3070
Epson SureColor F570
Epson SureColor F170
Epson SureColor F6470 and F6470H
Epson SureColor F6370
Epson SureColor F7200
Epson SureColor P-Series photo printers (P700, P900, P6570, P8570)
Epson SureColor T-Series CAD and technical printers
Epson SureColor S-Series (S40600, S60600, S80600)
xTool F1 Ultra settings explained: power, speed, passes, dot duration and image modes
Start every F1 Ultra job from xTool's tested settings: pick the material in xTool Studio or look it up in xTool's Materials Lab, then run a Material Test Array on your own stock. More power, slower speed or more passes all mean deeper marks. For photos, xTool generally suggests Jarvis mode with the fiber laser and Grayscale with the blue laser, and a dot duration over 100 microseconds for steady output.
Where the numbers should come from
- Inside xTool Studio: choose Process on flat surface, click Unknown Material, pick the material and click Apply. Studio fills in the laser type and settings xTool tested on the F1 Ultra.
- xTool Materials Lab at atomm.com/materials-lab: the Official tab holds xTool's tested settings. Filter by machine (F1 Ultra) and laser. The Community tab is other users' settings, so treat those as untested.
- Your own test: for anything else, run a Material Test Array (under Applications in xTool Studio). The software sets each square's settings for you; you just pick the square you like.
Our general guide to xTool's material library walks through all three in more detail.
What each setting does
| Setting | What it changes |
|---|---|
| Laser type | Blue diode for wood, leather, paper, acrylic and cutting; fiber infrared for metals |
| Power (%) | Higher power marks deeper. Whole numbers, 1 to 100. |
| Speed (mm/s) | Slower means more energy into the material and a deeper mark |
| Pass | More passes, deeper result. Engraving allows 1 to 10; cutting allows many more. |
| Lines per cm | How tightly engraved lines are packed. 100 lines per cm equals 254 DPI. |
| Frequency | Fiber laser only. Higher frequency fires faster but with lower peak power per pulse. |
Photos and images
- Image mode: xTool's general advice is Jarvis for the fiber laser and Grayscale for the blue laser. Floyd suits highly detailed images; Stucki is a little faster than Jarvis; Sierra is a sharper variant.
- Dot duration: the time the laser spends on each dot. xTool recommends more than 100 microseconds for steady output, especially with the fiber laser, and says the best value usually falls between 100 and 500. Too long can whiten the image and slows the job.
- DPI: higher DPI is finer only up to the image's own resolution. Past that, dots crowd together and dark materials can turn pale.
- Engraving mode: bi-directional is quicker; uni-directional is slower but sharper at the edges.
Habits that save material
-
Focus first
Every setting assumes the red and blue spots overlap on the surface. Out of focus, no setting will look right.
-
Set every object
Each object on the canvas needs its own settings. One you miss may not be processed.
-
Keep material clean and dry
xTool notes that moisture and contamination change results a lot.
-
Thin metal: many fast passes
xTool's advice for cutting thin metal is many high-speed repeat passes rather than one slow pass, because heat warps thin sheet and pulls it out of focus.
-
Save what works
Save your tested settings as your own material in xTool Studio so you can reuse them.
Watch xTool Studio 101: the pre-laser checklist
More videos
Embedded from the manufacturer's official channel.
Common questions
Can you send me power and speed numbers for my material?
We don't publish our own tables. xTool tests its materials on each machine and posts the results in xTool Studio and its Materials Lab, and those are the safest starting point. Test anything else on scrap.
Why don't xTool's settings work on my material?
xTool says its recommended settings give the best results on xTool's own materials. Other brands, moisture and coatings all change the result, so run a test array.
Bi-directional or uni-directional?
Bi-directional is faster but edges can be less crisp. Uni-directional takes longer but gives cleaner detail.
Why does my photo come out pale or washed out on dark material?
xTool warns that setting DPI higher than the image's own pixel density, or using too long a dot duration, can whiten the result. Lower the DPI to match the image.
How thin a metal can the F1 Ultra cut?
xTool quotes 0.4 mm brass, 0.3 mm stainless steel and 0.2 mm aluminum using many fast repeated passes, which limits heat warping. For exact settings use xTool's library.
- The Processing Parameters for xTool F1 Ultra
- The Functions of xTool F1 Ultra
- (xTool Studio) How to Process on Flat Surface with xTool F1 Ultra
- xTool F1 Ultra Q&A
- How to Perform an Array Test on a Material
- xTool Materials Lab (official settings)
- AA support requests about xTool material settings, 2024 to 2026











































































