Support
Machine type
Brand
xTool F2 Ultra

Cleaning the lens, mirrors and filters on xTool F2 Ultra, P3 and P2S lasers

✓ Reviewed by Jason KimUpdated 2 min readFits: F2 Ultra · P3 · P2S
Short answer

Shallow engraving or cuts that no longer go through usually mean dirty optics, not a dying laser. With the power off, wipe the optics gently in one direction with a lint-free cloth and alcohol. The F2 Ultra has one field lens, the P3 has a focus lens, window lens and mirror that xTool says to check daily, and the P2S has three mirrors xTool says to clean every 2 to 4 hours of use.

How often

Machine Optics Other parts
F2 Ultra Clean the field lens when engraving turns shallow or cuts stop going through Brush the fan module when smoke escapes the enclosure
P3 Check the focus lens, window lens and mirror every day. Clean every 4 hours in long high-power runs. Clear scraps from the bed after every job
P2S Clean the three mirrors every 2 to 4 hours of operation Clean the filter screens every 4 hours of continuous use; clean the exhaust fan when airflow drops

What you need

  • Lint-free or microfiber lens cloth, or lens paper and dust-free swabs
  • Absolute ethanol (F2 Ultra) or isopropyl alcohol or optical cleaner (P3, P2S)
  • An air blower, and nitrile or latex gloves
  • The screwdriver that came with the machine

Always turn the machine off and unplug it first. On the F2 Ultra, also remove the safety key. Alcohol is flammable: keep it away from heat and open flame, and do not spray it into the machine.

Cleaning the optics

  1. Watch xTool's video for your model

    The P3 and P2S lenses and mirrors sit in holders that must go back the right way. Follow xTool's video for your machine to remove and refit them.

  2. Handle by the edge

    Wear gloves and hold mirrors by the edge or the magnetic ring, never the face. Set them on a clean cloth, not the table.

  3. Blow off loose dust first

    Use an air blower before you touch the surface. Wiping grit around scratches the coating permanently.

  4. Wipe once, in one direction

    Dampen the cloth or swab with alcohol and wipe gently across the surface in a single direction. Do not scrub back and forth.

  5. Let it dry

    If you used a slow-drying alcohol, dry the surface with a soft cloth so liquid marks do not damage the coating.

  6. Refit and check the optical path

    On the P3 and P2S, reinstall exactly as shown in the video, then check the optical path before cutting again. A mirror put back crooked can send the beam where it should not go.

Fans and filters

  • F2 Ultra fan module: remove the magnetic guard from the smoke outlet, open the cover, take out the module and brush it and the guard clean. Never rinse or soak it.
  • P2S filter screens: they are magnetic. Pull them off, rinse with clean water, brush off what is left, dry and refit.
  • P2S exhaust fan: clean it with xTool's video; it is not made to be submerged.

When to replace instead of clean

Replace a lens or mirror with black burn spots that go through the coating, heavy oxidation, or cracks. xTool's testing found light edge marks cost very little power, so do not replace a mirror over a small blemish. If power is still low after clean optics, text us your settings and a photo of the test at (562) 609-4996.

Common questions

What alcohol should I use?

xTool calls for absolute (anhydrous) ethanol on the F2 Ultra field lens, and isopropyl alcohol or a high-concentration optical cleaner on the P-series mirrors and lenses. If you use a slow-drying 75% alcohol, dry the surface afterward so it does not stain the coating.

There are small spots on my mirror that will not come off.

Small marks at the edge barely affect power, according to xTool's own testing. Replace the mirror if it has black burn spots through the coating, or if power has dropped noticeably.

Can I wash the exhaust fan?

No. Brush the F2 Ultra fan module, and do not submerge the P2S exhaust fan. Only the P2S filter screens get rinsed with water.

Do I need to realign after cleaning?

On the P3 and P2S, xTool says to check the optical path after removing and refitting a lens or mirror.

Did this fix it?