Machine type
Prestige XL series (L2, XL2, XL2 Pro, XL3, XL4)
DTF Station Prestige R2 Pro
DTF Station Prestige R1
DTF Station Prestige R2 (original)
Prestige X6
DTF Station Prestige A4
DTF Station Prestige A3+ and A3+ R
Epson SureColor G6070 DTF printer
Mimaki TxF300-1600
Mimaki TxF330-800
STS XPD-924D DTF Printer (Mutoh)
STS VJ-628D DTF Printer (Mutoh)
DTF Station Vega S17
STS XpertJet 1682D (XPJ-1682D) 64 inch DTF Printer
STS XPD-724 DTF Printer (Mutoh)
Hotronix Fusion IQ, Air Fusion IQ and Dual Air Fusion IQ
Geo Knight DK20S and DK20SP Digital Knight Swing-Away Presses
DTF Station Maxima and Proxima Dual Heat Presses
Hotronix Auto Open Clam and Hover Heat Press
DTF Station Prisma Auto Heat Press
DTF Station Prisma Dual Heat Press
DTF Station Prisma Swing Heat Press
Insta 718, 728 and 828 Automatic Swing-Away Heat Presses
DTF Station Prisma Sentry Heat Press
Geo Knight DC16 and DC16AP Digital Combo Swing-Away Presses
Geo Knight DK Digital Clamshell Presses: DK20, DK16, DKA Auto, DK8 Label and DK7 Cap
Hotronix Auto Open Cap Press and 360 IQ Hat Press
Hotronix Craft Heat Press 9 x 12
Hotronix Mighty Mug Heat Press
Insta 256 and 288 Manual Swing-Away Heat Presses
Insta 907 Dual Station Shuttle Label Heat Press
Viper MAXX pretreatment machine
Ecofreen Mister-T2 and Mister-T2 Pro pretreatment machines
Pearl Elite and Pearl PTM DTG pretreatment machines
Viper XPT-1000 pretreatment machine
Lawson Silver-Jet and Silver-Jet V2 DTG Pretreat Sprayers
Lawson Zoom-AE DTG pretreatment machine
Viper MINI handheld DTG pretreatment machine
Brand
Prestige XL series (L2, XL2, XL2 Pro, XL3, XL4)
DTF Station Prestige R2 Pro
DTF Station Prestige R1
DTF Station Prestige R2 (original)
Prestige X6
DTF Station Prestige A4
DTF Station Prestige A3+ and A3+ R
DTF Station Aries 124 UV DTF printer
Miro DTF Powder Shakers: Miro 13 Max, 16, 24 and 36
DTF Station Aries 213 and Aries 113 UV DTF printers
Seismo L16R and L24R DTF Powder Shaker and Dryer
Phoenix Air 16x20 DTF Curing Oven
DTF Station Maxima and Proxima Dual Heat Presses
DTF Station Prisma Auto Heat Press
DTF Station Prisma Dual Heat Press
DTF Station Prisma Swing Heat Press
DTF Station Vega S17
DTF Station Prisma Sentry Heat Press
DTF Station Seismo V36R DTF Powder Shaker and Dryer
DTF Station Arc 127 automatic cutter for DTF and UV DTF film
Epson SureColor F2100
Epson SureColor G6070 DTF printer
Epson SureColor F2270
Epson SureColor F3070
Epson SureColor F570
Epson SureColor F170
Epson SureColor F6470 and F6470H
Epson SureColor F6370
Epson SureColor F7200
Epson SureColor P-Series photo printers (P700, P900, P6570, P8570)
Epson SureColor T-Series CAD and technical printers
Epson SureColor S-Series (S40600, S60600, S80600)
xTool laser first setup: install xTool Studio and connect over USB, Wi-Fi or IP
Install xTool Studio from xTool's software page, connect the laser with its USB cable the first time, and pick it under Select device > Add Device. Once it connects, set up Wi-Fi from Device settings > Basic info > Wi-Fi setting with the computer on the same network. xTool Creative Space (XCS) is legacy software, and the P3 does not work with it at all.
Before you plug in a P3 or P2S
The P3 and P2S have water-cooled laser tubes. Fill the coolant tank with xTool's antifreeze and purified water, in the amounts the quick start guide gives for your area's lowest yearly temperature, before you connect power. Never use tap water. On the P3, also remove the thumb screws from the X and Y rails, insert the key, and twist the emergency stop to release it.
On the F2 Ultra, pull off the field lens protector, insert the key, make sure the emergency stop is released, connect the touchscreen controller and power, and fit the exhaust pipe.
Install the software
-
Check your computer
xTool's minimum is an Intel Core i5-6200U, 8 GB RAM, 8 GB of free disk and a 1280 x 720 screen, on 64-bit Windows 10 or later or a current macOS. Very large images (over 50 megapixels, or SVGs over 1 MB) may lag on the minimum.
-
Download xTool Studio
Get it from xTool's software page at xtool.com/pages/software. Install it, open it, and set your language under the menu icon in the top right, Settings > General.
Connect over USB the first time
-
Plug in the USB cable
Use the cable that came with the laser. On the P3, use the port marked for USB connection, not the access-control key port. Turn the laser on.
-
Add the device
In xTool Studio, click + New Project, then Select device on the right. Click Add Device and click your machine's name. If you have connected an xTool before, click the icon next to the current device instead.
-
Check the firmware
Open Device settings > Basic info and click Check for updates next to Firmware version. On the P3, firmware 007 and later only works with xTool Studio 1.58 or newer.
Set up Wi-Fi
-
Open the Wi-Fi setting
With USB still connected, go to Device settings > Basic info and click Setting next to Wi-Fi setting.
-
Pick the network
Choose your network, type the password and click Next. The computer must be on the same network as the laser. If your router has separate 2.4 GHz and 5 GHz names, put both on the same one.
-
Connect with Wi-Fi
Click Connect with Wi-Fi, then choose the device under the Wi-Fi tab. You can now unplug USB.
Connect by IP address
After Wi-Fi is set, the laser's IP address shows under Wi-Fi setting in Device settings > Basic info. Write it down. Later, if the laser does not show up over Wi-Fi, open Connect device, choose IP, enter the address and click Connect.
F2 Ultra settings worth checking
- Stops when enclosure opened: keep this on so the laser stops if the lid lifts.
- Flame alarm: pauses the job and sounds an alarm if flame is detected.
- Stops when moved: pauses the job if the machine is bumped or tilted.
- Exhaust time after processing: lengthen it if smoke lingers after a job.
Stuck on any step? See our guide to xTool connection problems, or text us a photo of the screen at (562) 609-4996.
Common questions
Is xTool Studio the same as XCS?
xTool Studio is the replacement. xTool says XCS is legacy software that is no longer maintained, and the P3 only works with xTool Studio.
Do I need the USB cable if I want to use Wi-Fi?
Yes, for the first connection. Connect over USB, set up Wi-Fi from the device settings, and after that you can connect over Wi-Fi without the cable. Switching to a new network needs USB again.
My computer does not have the right USB port.
Use an adapter. xTool notes the included cable may not fit every computer and the adapter is not included.
Will my old laptop run xTool Studio?
xTool's minimum is an Intel Core i5-6200U, 8 GB RAM, 8 GB free disk and Windows 10 64-bit or a recent macOS. Big image files run smoother on the recommended i5-11600 with 16 GB RAM.
- Connect and Set Up xTool F2 Ultra with xTool Studio
- Connect xTool F2 Ultra to XCS on the Computer
- xTool P3 User Manual
- Troubleshooting: USB Connection Issues with xTool P3
- xTool P2S User Guide
- AA support requests about xTool setup, 2024 to 2026











































































