Machine type
Prestige XL series (L2, XL2, XL2 Pro, XL3, XL4)
DTF Station Prestige R2 Pro
DTF Station Prestige R1
DTF Station Prestige R2 (original)
Prestige X6
DTF Station Prestige A4
DTF Station Prestige A3+ and A3+ R
Epson SureColor G6070 DTF printer
Mimaki TxF300-1600
Mimaki TxF330-800
STS XPD-924D DTF Printer (Mutoh)
STS VJ-628D DTF Printer (Mutoh)
DTF Station Vega S17
STS XpertJet 1682D (XPJ-1682D) 64 inch DTF Printer
STS XPD-724 DTF Printer (Mutoh)
Hotronix Fusion IQ, Air Fusion IQ and Dual Air Fusion IQ
Geo Knight DK20S and DK20SP Digital Knight Swing-Away Presses
DTF Station Maxima and Proxima Dual Heat Presses
Hotronix Auto Open Clam and Hover Heat Press
DTF Station Prisma Auto Heat Press
DTF Station Prisma Dual Heat Press
DTF Station Prisma Swing Heat Press
Insta 718, 728 and 828 Automatic Swing-Away Heat Presses
DTF Station Prisma Sentry Heat Press
Geo Knight DC16 and DC16AP Digital Combo Swing-Away Presses
Geo Knight DK Digital Clamshell Presses: DK20, DK16, DKA Auto, DK8 Label and DK7 Cap
Hotronix Auto Open Cap Press and 360 IQ Hat Press
Hotronix Craft Heat Press 9 x 12
Hotronix Mighty Mug Heat Press
Insta 256 and 288 Manual Swing-Away Heat Presses
Insta 907 Dual Station Shuttle Label Heat Press
Viper MAXX pretreatment machine
Ecofreen Mister-T2 and Mister-T2 Pro pretreatment machines
Pearl Elite and Pearl PTM DTG pretreatment machines
Viper XPT-1000 pretreatment machine
Lawson Silver-Jet and Silver-Jet V2 DTG Pretreat Sprayers
Lawson Zoom-AE DTG pretreatment machine
Viper MINI handheld DTG pretreatment machine
Brand
Prestige XL series (L2, XL2, XL2 Pro, XL3, XL4)
DTF Station Prestige R2 Pro
DTF Station Prestige R1
DTF Station Prestige R2 (original)
Prestige X6
DTF Station Prestige A4
DTF Station Prestige A3+ and A3+ R
DTF Station Aries 124 UV DTF printer
Miro DTF Powder Shakers: Miro 13 Max, 16, 24 and 36
DTF Station Aries 213 and Aries 113 UV DTF printers
Seismo L16R and L24R DTF Powder Shaker and Dryer
Phoenix Air 16x20 DTF Curing Oven
DTF Station Maxima and Proxima Dual Heat Presses
DTF Station Prisma Auto Heat Press
DTF Station Prisma Dual Heat Press
DTF Station Prisma Swing Heat Press
DTF Station Vega S17
DTF Station Prisma Sentry Heat Press
DTF Station Seismo V36R DTF Powder Shaker and Dryer
DTF Station Arc 127 automatic cutter for DTF and UV DTF film
Epson SureColor F2100
Epson SureColor G6070 DTF printer
Epson SureColor F2270
Epson SureColor F3070
Epson SureColor F570
Epson SureColor F170
Epson SureColor F6470 and F6470H
Epson SureColor F6370
Epson SureColor F7200
Epson SureColor P-Series photo printers (P700, P900, P6570, P8570)
Epson SureColor T-Series CAD and technical printers
Epson SureColor S-Series (S40600, S60600, S80600)
Lawson Zoom-AE daily cleaning and weekly maintenance: Lawson's routine
Every day you spray, even once, purge distilled water through the Zoom-AE until the lines run clear (10 to 15 seconds), pop the tip out and soak it in distilled water overnight, brush it with a soft toothbrush, and wipe the inside with hot soapy water. Once a week, or every few days in a busy shop, purge Lawson's Magic Clean for 8 to 15 seconds and follow it with distilled water. Never use tap water in the fluid system.
Lawson puts it plainly: pretreat is glue suspended in salt water. Whatever coats the shirt also coats the spray tip and valve, and if it dries there you get clogs and uneven spray. The routine is the same whether you sprayed one shirt or a hundred.
Every production day, right after you finish
-
Purge with distilled water
Close the pretreat jug's valve and open the distilled water jug's valve (only one open at a time unless both jugs are full). Hold a container under the tip and press the Prime button, or run spray cycles, until the lines are visibly clear of pretreat. That usually takes 10 to 15 seconds. Lawson says this step matters more than any other.
-
Soak the tip
Remove the quick exchange cap, take out the spray tip and soak just the tip in distilled water (or Magic Clean) overnight. Keep the rubber gasket that sits inside the plastic cap out of the soak.
-
Brush the tip
Clean the tip inside and out with a soft bristle toothbrush to lift salt deposits. If the opening is blocked, use the toothbrush and a can of compressed air. Never push a needle or pin into it: that scores the metal and ruins the tip.
-
Wash the inside
Wipe every inside surface with a sponge and hot soapy water, then dry it. It takes about five minutes. Skip it and the pretreat corrodes the finish and cakes so thick that a shirt dragging across it can pick up marks.
Weekly
-
Run Magic Clean through it
At least once a week, or every few days if you run production or more than one shift, put the fluid hose in Lawson's Magic Clean and purge for 8 to 15 seconds. Wear goggles and keep it out of your eyes. Then purge distilled water to leave the system parked on water.
-
Lubricate the drawer slides
Spray the slides with a silicone spray or WD-40 so the drawer runs smoothly.
-
Clean and oil the head rail
Clean the head rail and the extrusion slide surface, then lubricate them. Lint and dried pretreat here make the head travel unevenly, and uneven travel means uneven spray.
Unplug the power cord before you clean or service anything inside the machine.
Spares Lawson says to keep on hand
- Spray tips: at least one spare. Lawson offers WENL (standard width), WENA (standard width, less fluid), OENA (narrower, less fluid) and WENF (for polyester pretreat).
- Slip-on tube filters: about four. They catch debris before it reaches the internal lines.
- Fluid valve and fluid pump: worth stocking if you can't afford downtime.
If the spray still looks uneven after a full clean, see our Zoom-AE spray troubleshooting guide, or text us a photo of the sprayed shirt at (562) 609-4996.
Watch Lawson's video: Zoom-AE daily maintenance
More videos
Embedded from the manufacturer's official channel.
Common questions
Can I use tap water to flush?
No. Lawson says distilled water is the only water for the fluid system and the tip, because tap water minerals leave deposits that damage spray parts.
Do I soak the rubber gasket with the tip?
No. Soak only the tip. Lawson says not to soak the rubber gasket that sits inside the plastic cap next to the tip.
How do I clear a blocked tip opening?
Lawson's current guide says a soft toothbrush and a can of compressed air. Never use a needle or pin: it scores the metal opening and ruins the tip.
What do I put on the drawer slides?
A silicone spray or WD-40, once a week.
Does Lawson's warranty cover clogged tips?
Lawson's parts warranty excludes nozzles, tips and filters, and says skipping the daily cleaning voids the warranty.










































































