Machine type
Prestige XL series (L2, XL2, XL2 Pro, XL3, XL4)
DTF Station Prestige R2 Pro
DTF Station Prestige R1
DTF Station Prestige R2 (original)
Prestige X6
DTF Station Prestige A4
DTF Station Prestige A3+ and A3+ R
Epson SureColor G6070 DTF printer
Mimaki TxF300-1600
Mimaki TxF330-800
STS XPD-924D DTF Printer (Mutoh)
STS VJ-628D DTF Printer (Mutoh)
DTF Station Vega S17
STS XpertJet 1682D (XPJ-1682D) 64 inch DTF Printer
STS XPD-724 DTF Printer (Mutoh)
Hotronix Fusion IQ, Air Fusion IQ and Dual Air Fusion IQ
Geo Knight DK20S and DK20SP Digital Knight Swing-Away Presses
DTF Station Maxima and Proxima Dual Heat Presses
Hotronix Auto Open Clam and Hover Heat Press
DTF Station Prisma Auto Heat Press
DTF Station Prisma Dual Heat Press
DTF Station Prisma Swing Heat Press
Insta 718, 728 and 828 Automatic Swing-Away Heat Presses
DTF Station Prisma Sentry Heat Press
Geo Knight DC16 and DC16AP Digital Combo Swing-Away Presses
Geo Knight DK Digital Clamshell Presses: DK20, DK16, DKA Auto, DK8 Label and DK7 Cap
Hotronix Auto Open Cap Press and 360 IQ Hat Press
Hotronix Craft Heat Press 9 x 12
Hotronix Mighty Mug Heat Press
Insta 256 and 288 Manual Swing-Away Heat Presses
Insta 907 Dual Station Shuttle Label Heat Press
Viper MAXX pretreatment machine
Ecofreen Mister-T2 and Mister-T2 Pro pretreatment machines
Pearl Elite and Pearl PTM DTG pretreatment machines
Viper XPT-1000 pretreatment machine
Lawson Silver-Jet and Silver-Jet V2 DTG Pretreat Sprayers
Lawson Zoom-AE DTG pretreatment machine
Viper MINI handheld DTG pretreatment machine
Brand
Prestige XL series (L2, XL2, XL2 Pro, XL3, XL4)
DTF Station Prestige R2 Pro
DTF Station Prestige R1
DTF Station Prestige R2 (original)
Prestige X6
DTF Station Prestige A4
DTF Station Prestige A3+ and A3+ R
DTF Station Aries 124 UV DTF printer
Miro DTF Powder Shakers: Miro 13 Max, 16, 24 and 36
DTF Station Aries 213 and Aries 113 UV DTF printers
Seismo L16R and L24R DTF Powder Shaker and Dryer
Phoenix Air 16x20 DTF Curing Oven
DTF Station Maxima and Proxima Dual Heat Presses
DTF Station Prisma Auto Heat Press
DTF Station Prisma Dual Heat Press
DTF Station Prisma Swing Heat Press
DTF Station Vega S17
DTF Station Prisma Sentry Heat Press
DTF Station Seismo V36R DTF Powder Shaker and Dryer
DTF Station Arc 127 automatic cutter for DTF and UV DTF film
Epson SureColor F2100
Epson SureColor G6070 DTF printer
Epson SureColor F2270
Epson SureColor F3070
Epson SureColor F570
Epson SureColor F170
Epson SureColor F6470 and F6470H
Epson SureColor F6370
Epson SureColor F7200
Epson SureColor P-Series photo printers (P700, P900, P6570, P8570)
Epson SureColor T-Series CAD and technical printers
Epson SureColor S-Series (S40600, S60600, S80600)
Lawson Zoom-AE not spraying, uneven spray or dripping: what to check
Lawson says a partly clogged spray tip is the number one cause of uneven spray, and dried pretreat is the usual reason a Zoom-AE stops spraying. Check that only the valve for a full jug is open, purge with distilled water and then Magic Clean, and clean or replace the tip and the slip-on filter. If the spray is still uneven, slow the head down and make sure your pretreat hasn't settled. Electrical faults such as fuses, relays and switches are for a technician.
Match your symptom
| What you see | Most likely cause | Go to |
|---|---|---|
| Pump runs but nothing sprays, or it won't prime | Wrong valve open, empty jug, or dried pretreat in the tip or spray head | Steps 1 to 3 |
| Streaky, blotchy or uneven coverage | Partly clogged tip, speed too fast, clogged filter, settled pretreat | Steps 3 to 6 |
| Three or more drips at the end of a pass | Debris in the tip | Step 3 |
| Spray band off to one side | Spray head not centered | Step 4 |
| Head moves unevenly, stalls or won't travel | Dirty or dry extrusion, loose pulley or belt | Step 7 |
| Nothing works, or the spray won't turn off | Power, fuse, switch or spray head fault | Contact us |
Step by step
-
Check the jugs and valves
Each jug has its own on/off fluid valve. Open only the valve for the jug you're spraying from. If both are open and one jug is empty, Lawson says the pump won't prime.
-
Purge, then purge with Magic Clean
Hold a container under the tip and press Prime with distilled water until the line runs clear. If it still won't spray or the pattern stays poor, purge Lawson's Magic Clean through the whole system for 8 to 15 seconds, then distilled water again. Wear goggles.
-
Clean or replace the spray tip
Remove the quick exchange cap and the tip. Brush it inside and out with a soft toothbrush and blow the opening clear with compressed air. Never use a needle. Lawson names a partly clogged tip as the number one cause of uneven spray, and the usual reasons are not purging right after spraying, purging for less than 10 seconds, skipping the weekly Magic Clean, and hot rooms. If cleaning doesn't fix it, fit a new tip. Tips are a wear item, so keep a spare.
-
Center the spray head
If the band is lopsided, Lawson's chart says to center the spray head over the platen. Unplug the machine before you adjust anything.
-
Replace the slip-on filter
The slip-on tube filter on the fluid line catches debris before it reaches the pump. A clogged one starves the spray. They're cheap: Lawson suggests keeping about four on hand.
-
Check the speed and the pretreat
If the pattern is clean but too light, slow the head down with the speed knob to put more pretreat on, and weigh a shirt to confirm. Heavier and different garments need different speeds. Also check the pretreat itself: Lawson notes some pretreats separate and settle, so the binder, salt and water are no longer mixed evenly.
-
Make sure the head travels smoothly
Uneven travel speed gives uneven spray. Clean lint and dried pretreat off the head rail and extrusion, then lubricate it. Lawson also lists a slipping belt or a loose set screw on the drive pulley. If cleaning the rail doesn't fix it, text us before you open the machine.
Lawson's chart also covers fuses, relays, micro switches, transformer voltage and pump voltage tests. Those mean working inside the control box with power on. Unplug the machine and text us a short video at (562) 609-4996 instead.
Watch Lawson's video: cleaning the Zoom-AE spray tip at the end of the day
Embedded from the manufacturer's official channel.
Common questions
Why won't my Zoom-AE prime?
Check the fluid valves on the jugs. Lawson notes that if both valves are open and one jug is empty, the pump won't prime. Open only the valve for the jug you're using.
It drips three or four times after every pass. Why?
Lawson says three or more drips at the end of a cycle usually means debris in the tip is trapping the flow. Clean or replace the tip.
Should I spray twice instead of slowing down?
On some difficult garments, Lawson notes that some customers speed the head up and spray the shirt twice. Weigh the result either way.
Is there a different tip for polyester pretreat?
Yes. Lawson offers special tips for polyester pretreat (the WENF style). Ask us which one fits your setup.
Can I check the fuse or pump voltage myself?
Lawson's troubleshooting chart includes voltage and fuse checks, but they mean working inside a live control box. Text us and we'll walk you through what's safe or arrange service.











































































