Support
Machine type
Brand
Lawson Zoom-AE DTG pretreatment machine

Lawson Zoom-AE setup: power, buckets, priming the pump, setting the spray amount and spray length

✓ Reviewed by Jason KimUpdated 2 min readFits: Lawson Zoom-AE
Short answer

Plug the Zoom-AE into 120 V (it needs 5 amps), fit the two catch buckets at the back, and stand a gallon of pretreat and a gallon of distilled water in the container spaces. Open only one fluid valve and press Prime until fluid flows. Set the amount with the spray speed knob and confirm it by weighing a shirt before and after spraying; set the spray length by moving the spray limit switch bracket.

Get it ready

  1. Power

    The Zoom-AE runs on 120 V and needs 5 amps.

  2. Catch buckets

    Fit the two pretreat and waste collecting buckets supplied with the machine at the rear of the unit. They catch the overspray.

  3. Containers

    There is room for two one-gallon containers. Lawson says the most popular setup is one gallon of pretreat and one gallon of distilled water for cleaning. Some shops run the same pretreat in both for long runs (over 250 shirts before refilling), or two different pretreats.

  4. Filters

    Each container line has a slip-on tube filter that keeps debris out of the system. Lawson suggests keeping four spares.

  5. Level it

    The leveling legs have adjustment bolts. Set the unit level and steady.

The control box

Control What it does
Power toggle Turns the unit on and off
Prime Runs the pump to pull fluid through and purge the tip
Start The head comes forward, reverses and sprays the garment
Speed knob Sets how fast the spray head travels, which sets the grams on the shirt

Prime the pump

  1. Open one valve

    Turn on only the mechanical fluid valve for the container you're spraying from. If both valves are on and the second container is empty, the pump won't prime.

  2. Prime

    Hold a container under the tip and press Prime until fluid flows from the tip.

Set the amount

Lawson says the grams on the fabric come from three things: the travel speed of the spray head, the spray tip design, and the distance from the tip to the fabric. In everyday use, the speed knob is your main control.

  1. Weigh the shirt

    Put the dry garment in a container on a gram scale and tare it so it reads zero.

  2. Spray it

    Load the shirt on the platen and press Start.

  3. Weigh again

    Put it back in the container on the scale. The reading is how much pretreat went on.

  4. Adjust

    Change the speed knob and repeat until you hit the amount your pretreat maker recommends. Write the knob setting down for each garment type.

For target amounts by fabric, see how much DTG pretreat to use. The standard tip that ships with the Zoom-AE suits most work. Lawson makes specialty tips if you need them. The quick-exchange cap holds the tip in the right spraying position whichever way you put it in.

Set the spray length

The spray always starts after the head travels to the front and reverses. The front limit switch starts the spray and the rear limit switch stops it. Move the spray limit switch bracket to change where it starts and stops. Lawson notes that a big change in spray speed can shift the start and stop points, so check the length again after a large speed change.

Clean it at the end of every day, whether you sprayed one shirt or a hundred. Pretreat that dries in the tip clogs it, and nozzles and filters aren't covered by Lawson's parts warranty. Follow Zoom-AE daily cleaning.

If it won't spray or sprays unevenly, see Zoom-AE not spraying. If the head doesn't move or a fuse blows, Text us a photo or short video at (562) 609-4996.

Watch Lawson: Zoom-AE pre-treat sprayer overview

Embedded from the manufacturer's official channel.

Common questions

Why won't the pump prime?

Check that only one fluid valve is open. Lawson says that if both valves are on and the second container is empty, the pump will not prime.

How do I know how much pretreat is on the shirt?

Put the dry shirt in a container on a gram scale, tare it to zero, spray it, then weigh it again. The reading is the pretreat on the shirt.

What changes the amount of pretreat?

Three things, per Lawson: the travel speed of the spray head, the spray tip design, and the distance from the tip to the fabric.

It drips at the end of each spray. Why?

Lawson says three or more drips at the end of a cycle usually means the tip isn't clean. Debris in the tip traps the fluid. Clean it as in the daily routine.

Can I use tap water to flush it?

No. Use distilled water only. Lawson says minerals in tap water form deposits that damage the spray tip and valves.

Sources
Did this fix it?