Support
Machine type
Brand
Epson SureColor F2100

Epson F2100 daily, weekly and monthly maintenance, step by step

✓ Reviewed by Jason KimUpdated 2 min readFits: F2100
Short answer

Epson's F2100 routine takes about 5 minutes a day, 5 to 10 minutes a week and 5 minutes a month. Every working day, shake the two white cartridges, print a nozzle check and run a Light cleaning only on channels with gaps. Every week, clean the suction cap. Every month, shake the color cartridges and check for firmware and Garment Creator updates. Replace the head cleaning set, air filter and waste bottle when the printer asks.

Every working day (about 5 minutes)

  1. Shake the white cartridges

    The screen reminds you every 24 hours. Pull out both white cartridges and shake each one hard for 15 seconds in total: about 8 seconds, flip it over, then finish to 15. Put them back. The printer also circulates the white ink in its tubes every 30 minutes on its own (about 15 seconds, no ink used), but that doesn't replace shaking.

  2. Print a nozzle check

    Make sure spacers a and b are on and a medium platen or grip pad is installed. Remove the platen frame and tape a letter-size sheet to the center. Set the height lever to P for a platen or 1 for a grip pad. Press the maintenance button, choose Nozzle Check and press OK twice. White doesn't show on white paper, so use colored paper or clear film.

  3. Clean only what needs it

    If a channel has gaps, choose Head Cleaning > Selected Nozzles, pick the channels and run Light. Epson suggests starting the day with a selective Light cleaning on the white channels as needed. A full cleaning is only needed when more than 3 nozzles in a row are missing. If the countdown to the next automatic cleaning shows little time left, Epson suggests a Medium cleaning on both white channels or Preventive Cleaning, which resets the timer.

  4. Turn it off at night

    Use the power button. The printer runs up to 5 minutes of maintenance and caps the head before it shuts off.

Every week (5 to 10 minutes)

Clean the suction cap: Maintenance > Head Cap Cleaning > Yes. Peel off any dried ink film with the plastic tweezers, wipe inside the cap with a thin swab dampened with ink cleaning solution (rotate the swab), then wipe the outside and top edge with a large swab. Keep cleaner off the anti-drying caps to the right. A buzzer sounds 10 minutes after the head moves out, so have everything ready before you start. Close the cover, press OK and print a nozzle check. If the printer sits idle, still print a nozzle check at least once a week.

Every month (about 5 minutes)

Shake each color cartridge the same way, 15 seconds in total. Then check Epson's F2100 support page for new firmware and Garment Creator versions. Epson recommends keeping the two updated together as a matched set.

When the printer asks

Message What to do
Head cleaning set is nearing end of life / Head Cleaning Set Life Replace the wiper unit, anti-drying caps and flushing pad together: Maintenance > Head Cleaning Set. Always start it from the menu so the printer's life counter resets correctly.
See manual to clean scale and change air filter Turn the printer off. Clean the encoder strip with the cloth that comes with the new air filter, soaked in ink cleaning solution, wiping gently to the right. Don't touch the carriage shaft. Then swap the air filter until it clicks. Epson also says frequent D197 errors mean this job is due.
Prepare empty waste ink bottle Swap the bottle and press OK to reset the counter. If you swap it early, reset it with Maintenance > Waste Ink Counter.
Tube washing prompt Run Maintenance > Tube Washing. Have cleaning cartridges and fresh ink ready before you start.

Use the ink cleaning solution from Epson's maintenance kit only on the suction cap, the encoder strip and around the print head. Wear gloves, and never move the print head or platen by hand.

Stuck on a step? Text us a photo or short video at (562) 609-4996.

Watch Epson's video: cleaning the F2100 suction cap

Embedded from the manufacturer's official channel.

Common questions

Do I really have to shake the white every day?

Yes. White ink pigment settles in the cartridges and along the ink tubes. Epson says to remove and shake the white cartridges at the start of every working day or every 20 hours, and the printer prompts you every 24 hours.

Should I leave the F2100 on overnight?

No. Epson says to turn it off at the end of the day. It runs up to 5 minutes of maintenance before it shuts down. Always use the power button, never a power strip or breaker.

How often does the head cleaning set need replacing?

It depends on how much you print. Epson says it can be less than a week in round-the-clock production or every few months for light use. The screen warns you as it gets close, and the printer stops when the wiper reaches the end of its life, so keep a spare kit.

Can I turn off Power On Cleaning?

You can, in the Administrator menu under Preferences. Epson warns that without it, white sediment can build up and clog nozzles, and says to clean the head yourself if the printer has been off a long time.

How do I know the suction cap needs cleaning before the weekly date?

Epson's warning signs: head cleanings stop improving the nozzle check, or you don't see ink flowing through the maintenance tube on the right side during a Medium cleaning. A Suction Error message also means clean it now.

Did this fix it?