Support
Machine type
Brand
Epson SureColor F2100

Epson F2100 ink cartridge not recognized (Ink Cartridge Error): how to fix it

✓ Reviewed by Jason KimUpdated 2 min readFits: F2100
Short answer

An Ink Cartridge Error on the F2100 usually means the cartridge is in the wrong slot, isn't seated all the way, has a dirty or touched chip, or is cold enough to have condensation inside. Check the color matches the slot label, reseat it and power cycle the printer. A cartridge that arrived cold needs four hours or more at room temperature. If a different cartridge of the same color works, the first one is the problem.

Match your symptom

What you see Most likely cause Go to
Error right after you put a cartridge in Wrong slot, not seated, or chip touched Steps 1 to 3
Error on a cartridge that just arrived in cold weather Condensation inside the cartridge Step 4
Error stays after reseating and power cycling Faulty or expired cartridge Step 5
Printer won't print and says a slot is empty Every slot must hold a cartridge Step 2
A partly used cartridge leaks after you put it back Dried ink on the supply port Keeping cartridges healthy

Step by step

  1. Check the color and the slot

    Make sure the cartridge color matches the color shown on the screen and on the label on the ink door. Hold it with the label facing the side of the printer.

  2. Reseat it

    Open the cartridge cover, put your finger in the indentation on top and pull the cartridge straight out. Slide it all the way back in. Every slot needs a cartridge, ink or cleaning, or the printer can't print.

  3. Don't touch the chip, then power cycle

    The chip on the cartridge stores its ink level. Fingerprints or ink on it can stop the printer reading it. Close the cover, turn the printer off and back on.

  4. Warm up a cold cartridge

    If it came in from a cold truck or warehouse, take it out and leave it at room temperature for four hours or more, then reinstall it. Epson says the same for any cartridge stored cold for a long time.

  5. Try a different cartridge

    Install another cartridge of the same color. If that one works, the first cartridge is the problem. Check its expiry date, then text us a photo of its label at (562) 609-4996.

Shake every new cartridge for about 15 seconds before installing it. Flip white cartridges over and shake again. Never refill a cartridge.

Keeping cartridges healthy

  • Store cartridges at room temperature out of direct sunlight, and lay white cartridges flat.
  • Use them before the date on the package and within one year of installing them.
  • If you pull a cartridge before it's empty, wipe the ink supply port with a cleaning stick from the maintenance kit. Dried ink on the port can make it leak when you reinstall it. Keep the port dust-free, and don't tape over it.
  • Don't drop cartridges or take them apart.
  • Never leave a slot empty, even when the printer isn't in use. The ink inside the printer can dry out.

The 250 ml cartridges that ship with a new printer are mostly used up by the first ink charge, so have full-size cartridges ready before you start.

Common questions

It's a brand-new cartridge. Why won't the printer read it?

Check the slot and seating first, then think about temperature. Epson says condensation inside a cold cartridge can cause this error, and the fix is to leave it out at room temperature for at least four hours before reinstalling.

Can I use an expired cartridge?

Epson says no: replace cartridges past the date printed on the package, and use installed cartridges within one year of installing them.

The printer says empty but there's ink inside.

That's by design. Epson's printer stops before a cartridge is completely empty to protect the print head.

Ink ran out in the middle of a shirt. Can I keep going?

Yes. Replace the cartridge and printing continues, though Epson notes there may be a slight quality change where the cartridge was changed.

Can I refill cartridges or use non-Epson ink?

Epson says not to refill cartridges. It also warns that non-genuine ink may not show ink levels, is recorded by the printer, and can cause damage that Epson's warranty doesn't cover.

Did this fix it?