Machine type
Prestige XL series (L2, XL2, XL2 Pro, XL3, XL4)
DTF Station Prestige R2 Pro
DTF Station Prestige R1
DTF Station Prestige R2 (original)
Prestige X6
DTF Station Prestige A4
DTF Station Prestige A3+ and A3+ R
Epson SureColor G6070 DTF printer
Mimaki TxF300-1600
Mimaki TxF330-800
STS XPD-924D DTF Printer (Mutoh)
STS VJ-628D DTF Printer (Mutoh)
DTF Station Vega S17
STS XpertJet 1682D (XPJ-1682D) 64 inch DTF Printer
STS XPD-724 DTF Printer (Mutoh)
Hotronix Fusion IQ, Air Fusion IQ and Dual Air Fusion IQ
Geo Knight DK20S and DK20SP Digital Knight Swing-Away Presses
DTF Station Maxima and Proxima Dual Heat Presses
Hotronix Auto Open Clam and Hover Heat Press
DTF Station Prisma Auto Heat Press
DTF Station Prisma Dual Heat Press
DTF Station Prisma Swing Heat Press
Insta 718, 728 and 828 Automatic Swing-Away Heat Presses
DTF Station Prisma Sentry Heat Press
Geo Knight DC16 and DC16AP Digital Combo Swing-Away Presses
Geo Knight DK Digital Clamshell Presses: DK20, DK16, DKA Auto, DK8 Label and DK7 Cap
Hotronix Auto Open Cap Press and 360 IQ Hat Press
Hotronix Craft Heat Press 9 x 12
Hotronix Mighty Mug Heat Press
Insta 256 and 288 Manual Swing-Away Heat Presses
Insta 907 Dual Station Shuttle Label Heat Press
Viper MAXX pretreatment machine
Ecofreen Mister-T2 and Mister-T2 Pro pretreatment machines
Pearl Elite and Pearl PTM DTG pretreatment machines
Viper XPT-1000 pretreatment machine
Lawson Silver-Jet and Silver-Jet V2 DTG Pretreat Sprayers
Lawson Zoom-AE DTG pretreatment machine
Viper MINI handheld DTG pretreatment machine
Brand
Prestige XL series (L2, XL2, XL2 Pro, XL3, XL4)
DTF Station Prestige R2 Pro
DTF Station Prestige R1
DTF Station Prestige R2 (original)
Prestige X6
DTF Station Prestige A4
DTF Station Prestige A3+ and A3+ R
DTF Station Aries 124 UV DTF printer
Miro DTF Powder Shakers: Miro 13 Max, 16, 24 and 36
DTF Station Aries 213 and Aries 113 UV DTF printers
Seismo L16R and L24R DTF Powder Shaker and Dryer
Phoenix Air 16x20 DTF Curing Oven
DTF Station Maxima and Proxima Dual Heat Presses
DTF Station Prisma Auto Heat Press
DTF Station Prisma Dual Heat Press
DTF Station Prisma Swing Heat Press
DTF Station Vega S17
DTF Station Prisma Sentry Heat Press
DTF Station Seismo V36R DTF Powder Shaker and Dryer
DTF Station Arc 127 automatic cutter for DTF and UV DTF film
Epson SureColor F2100
Epson SureColor G6070 DTF printer
Epson SureColor F2270
Epson SureColor F3070
Epson SureColor F570
Epson SureColor F170
Epson SureColor F6470 and F6470H
Epson SureColor F6370
Epson SureColor F7200
Epson SureColor P-Series photo printers (P700, P900, P6570, P8570)
Epson SureColor T-Series CAD and technical printers
Epson SureColor S-Series (S40600, S60600, S80600)
Epson F2100 loading shirts: attaching a grip pad, using the platen frame and avoiding height errors
On the F2100, use either a grip pad or the platen frame, never both. Load the shirt with the shoulders toward the front, pull it gently over the edges, and smooth the print area with the grip pad tool until there's no slack, then tuck the rest around the platen. Wrinkles near the print area are the usual cause of Platen Height Errors. Run a head alignment after changing platen size.
Grip pad or platen frame?
A grip pad holds the shirt so it can't shift while printing, which cuts down on misalignment. Epson recommends one on the platen that came with the printer. Use one or the other, never both: with a grip pad on, leave the platen frame off. Don't put grip pads on the extra small, sleeve or medium grooved platens. On thin fabric with 50% or more polyester, ink can bleed through onto the grip pad.
Putting a grip pad on
-
Line it up
Peel off one section of backing. Lay the pad face down on a flat surface and set the platen in the center of it.
-
Stick it down in sections
Flip the platen over and rub the uncovered section to stick it. Lift the pad gently, peel the other two sections of backing, and rub each one down.
-
Fold the edges under
Peel the backing off the edges. Fold the long edges onto the back of the platen, then the corners, then the short edges. Turn it over and press all the edges down firmly.
To take one off, lay the platen face down, peel up the edges, then flip it and peel the pad off while holding the platen down. A plastic spatula helps with an old pad. Never heat it with hot air, and clean leftover glue with a cloth dampened in diluted neutral detergent, not alcohol or solvents.
Loading a shirt on a grip pad
-
Bring the platen forward
Press the moveable base button if the platen isn't already out.
-
Pull the shirt on, shoulders toward you
Load it so the shoulders face the front of the printer, and gently pull it over the edges of the pad to flatten it. Don't stretch it hard or quality suffers.
-
Smooth it with the grip pad tool
Run the grip pad tool across the print area up and down and side to side, starting from the edges, until there's no slack or crease. If the tool catches on a pre-treated shirt, put a heat-resistant release sheet between them. Wipe a dirty tool with a damp cloth.
-
Tuck the rest
Tuck the shirt around the platen so nothing hangs onto the moveable base.
Loading a shirt with the platen frame
-
Remove the frame and load the shirt
Take the frame off, pull the shirt on shoulders first, and flatten it over the platen edges.
-
Put the frame back and take up slack
Replace the frame, then gently pull the shirt edges outside the frame to remove slack. Tuck the shirt around the platen, and reposition the frame one last time so the shirt is held firmly but not stretched. Don't use the grip pad tool with the frame.
The printer measures the highest point of the garment. A wrinkle, crease or bit of slack near the frame can trigger a Platen Height Error or lower print quality. Seams, collars, zippers and pockets in the print area need a higher platen setting too.
Starting heights and swelling shirts
Epson's starting lever positions are 3 on both spacers for T-shirts on the standard platens, 4 with a grip pad, 3 for the sleeve or medium grooved platen with spacer b, and 8 for sweatshirts and thick fabric. If the height sensor trips halfway through a print, the shirt has probably swelled because the pre-treatment wasn't fully dry. Dry shirts completely, check the height is at 3 for a standard tee, take the frame off and smooth the shirt, and if needed narrow the white under-base in Garment Creator or your RIP. After printing, hold the shirt by the shoulders to lift it off, because the ink is still wet, and cure it right away.
After you change to a different size platen, run a head alignment. Questions about which platen fits a job? Text us at (562) 609-4996.
Watch Epson's video: loading a T-shirt on the grip pad
Embedded from the manufacturer's official channel.
Common questions
Do I need the platen frame with a grip pad?
No. Epson says not to use the frame when a grip pad is attached.
Which platens can take a grip pad?
The standard platens. Epson says not to put grip pads on the extra small, sleeve or medium grooved platens.
Why does ink show up on my grip pad?
On thin fabric with 50% or more polyester, ink can bleed through onto the pad.
The tool drags on pre-treated shirts. What do I do?
Put a heat-resistant release sheet between the grip pad tool and the shirt.
How do I get an old grip pad off?
Peel from the edges, using a plastic spatula if needed. Don't use hot air or solvents. Clean leftover glue with diluted neutral detergent.
- Epson F2100 User's Guide: Attaching the grip pad to the platen
- Epson F2100 User's Guide: Removing the grip pad from the platen
- Epson F2100 User's Guide: Loading a T-shirt on the grip pad
- Epson F2100 User's Guide: Loading a T-shirt on the platen
- Epson F2100 User's Guide: Repositioning the T-shirt
- Epson F2100 User's Guide: Adjusting the height of the platen
- Epson F2100 User's Guide: Installing the platen
- Epson Video Manuals: Attaching a Platen Grip Pad
- AA support requests about F2100 loading and platen height, 2024 to 2026










































































