Machine type
Prestige XL series (L2, XL2, XL2 Pro, XL3, XL4)
DTF Station Prestige R2 Pro
DTF Station Prestige R1
DTF Station Prestige R2 (original)
Prestige X6
DTF Station Prestige A4
DTF Station Prestige A3+ and A3+ R
Epson SureColor G6070 DTF printer
Mimaki TxF300-1600
Mimaki TxF330-800
STS XPD-924D DTF Printer (Mutoh)
STS VJ-628D DTF Printer (Mutoh)
DTF Station Vega S17
STS XpertJet 1682D (XPJ-1682D) 64 inch DTF Printer
STS XPD-724 DTF Printer (Mutoh)
Hotronix Fusion IQ, Air Fusion IQ and Dual Air Fusion IQ
Geo Knight DK20S and DK20SP Digital Knight Swing-Away Presses
DTF Station Maxima and Proxima Dual Heat Presses
Hotronix Auto Open Clam and Hover Heat Press
DTF Station Prisma Auto Heat Press
DTF Station Prisma Dual Heat Press
DTF Station Prisma Swing Heat Press
Insta 718, 728 and 828 Automatic Swing-Away Heat Presses
DTF Station Prisma Sentry Heat Press
Geo Knight DC16 and DC16AP Digital Combo Swing-Away Presses
Geo Knight DK Digital Clamshell Presses: DK20, DK16, DKA Auto, DK8 Label and DK7 Cap
Hotronix Auto Open Cap Press and 360 IQ Hat Press
Hotronix Craft Heat Press 9 x 12
Hotronix Mighty Mug Heat Press
Insta 256 and 288 Manual Swing-Away Heat Presses
Insta 907 Dual Station Shuttle Label Heat Press
Viper MAXX pretreatment machine
Ecofreen Mister-T2 and Mister-T2 Pro pretreatment machines
Pearl Elite and Pearl PTM DTG pretreatment machines
Viper XPT-1000 pretreatment machine
Lawson Silver-Jet and Silver-Jet V2 DTG Pretreat Sprayers
Lawson Zoom-AE DTG pretreatment machine
Viper MINI handheld DTG pretreatment machine
Brand
Prestige XL series (L2, XL2, XL2 Pro, XL3, XL4)
DTF Station Prestige R2 Pro
DTF Station Prestige R1
DTF Station Prestige R2 (original)
Prestige X6
DTF Station Prestige A4
DTF Station Prestige A3+ and A3+ R
DTF Station Aries 124 UV DTF printer
Miro DTF Powder Shakers: Miro 13 Max, 16, 24 and 36
DTF Station Aries 213 and Aries 113 UV DTF printers
Seismo L16R and L24R DTF Powder Shaker and Dryer
Phoenix Air 16x20 DTF Curing Oven
DTF Station Maxima and Proxima Dual Heat Presses
DTF Station Prisma Auto Heat Press
DTF Station Prisma Dual Heat Press
DTF Station Prisma Swing Heat Press
DTF Station Vega S17
DTF Station Prisma Sentry Heat Press
DTF Station Seismo V36R DTF Powder Shaker and Dryer
DTF Station Arc 127 automatic cutter for DTF and UV DTF film
Epson SureColor F2100
Epson SureColor G6070 DTF printer
Epson SureColor F2270
Epson SureColor F3070
Epson SureColor F570
Epson SureColor F170
Epson SureColor F6470 and F6470H
Epson SureColor F6370
Epson SureColor F7200
Epson SureColor P-Series photo printers (P700, P900, P6570, P8570)
Epson SureColor T-Series CAD and technical printers
Epson SureColor S-Series (S40600, S60600, S80600)
Epson F2270 DTF film printing: printer settings, loading film, powder and heat press
To print DTF film on the F2270, the printer must be in White ink mode and the job must be sent from Garment Creator 2 as a Film job. Load the film on a platen without a grip pad that's bigger than the sheet, keep spacers A and B on, set the platen gap lever to P and Platen Gap to Auto, and tape the film flat with opaque tape, never clear tape. Never pretreat film, and keep powder away from the printer.
What you need
- The printer in White ink mode (Menu > General Settings > Printer Settings > Printer Mode).
- A platen without a grip pad that's larger than your film. The printer ships with an M size hanger platen. Don't use the sleeve or medium-grooved platen.
- DTF film and powder, opaque adhesive tape, a tray bigger than the film, a sieve or powder shaker, and a mask and eye protection.
- A heat press, an oven or press for curing the powder, and a heat-resistant release sheet.
Step by step
-
Send the job as a Film job
Create the design in Garment Creator 2 and send it as a Film job. Epson warns that a job made for T-shirts puts down too much ink, which runs on the film.
-
Set up the platen
Bring the platen forward and remove the frame. Make sure both spacers A and B are on, Platen Gap is set to Auto, and the platen gap lever is at P. To move it, loosen the fixing lever, slide the lever left to P, and tighten it again.
-
Load the film
Check the preview in Garment Creator 2. The top of the preview is the front of the printer (the hanger side). Lay the film so the design stays inside its edges, perfectly flat, and secure it with opaque tape. Don't use film that's curled, bent or damaged.
-
Print
When the job arrives, a preview shows on the screen and the start light comes on. Check the film is loaded and press the start button.
-
Powder the film, away from the printer
Lift the film off flat. Tilting it or pulling it straight up can make ink drip. Set it print side up in the tray and cover the whole design generously with powder. Lift the film and flick the back to knock off the excess. Never powder near the printer, because powder inside it can cause a malfunction.
-
Cure, transfer and fix
Use the starting values below, then adjust for your film and powder. Peel when your film's instructions say to, as some films need to cool first.
| Stage | Cotton | Polyester |
|---|---|---|
| Cure powder (conveyor oven, film surface temperature) | 338°F, 150 seconds | 338°F, 150 seconds |
| Transfer with heat press | 338°F, 25 seconds | 284°F, 25 seconds |
| Fix ink, heat press again with release sheet | 338°F, 5 seconds | 284°F, 5 seconds |
Epson lists pressure as 4.2 N/cm² (about 6 psi) for transfer and fixing, and says to test because heat presses vary. Transfer and fixing must be done on a heat press, not in an oven.
If the film prints badly
| What you see | What to check |
|---|---|
| Horizontal stripes or uneven color | Print a nozzle check. Then try Media > Print Adjustments > Media Feed Adjustment: plus side for dark lines, minus side for faint lines. |
| Ink runs, or white shows around the design | Make sure you're printing on the printing side of the film and the job was sent as a Film job. Then adjust Ink Density, or raise Reduce White Area, in Garment Creator 2. |
| Too light or blurry | Spacers A and B on, lever at P, Platen Gap on Auto, film flat and taped. Then run Print Head Alignment. |
| Quality changes from print to print | Curled or bent film, or tape lifting. Reload it flat. |
Film and shirts need different feed and alignment values, so Epson recommends saving a separate media setting for each (Media > Media Management, up to 30). For alignment on film, Epson's DTF guide says to use Light Media under Standard, while the User's Guide suggests Dark Media to line up white with color. Start with Light Media and try Dark Media if white and color don't line up. Still stuck? Text us a photo at (562) 609-4996.
Epson's video: printing on DTFilm with the F2270
More videos
Embedded from the manufacturer's official channel.
Common questions
Do I need to pretreat DTF film?
No. Epson says not to apply pretreatment to film. White ink is still used, but the film doesn't need pretreatment.
Can I print film on the grip pad platen?
No. Epson says film can't be loaded correctly on a grip pad covered platen. Use a platen without a grip pad, and not the sleeve or medium-grooved platen.
Why not clear tape?
Epson warns clear tape can peel up unnoticed and rub against the print head. Use opaque tape.
Can I print film in Color ink mode?
No. The powder only sticks where white ink was printed, so the printer must be in White ink mode. Printers set up in High speed color mode can't print film at all.
What oven and heat press settings should I use?
Epson's DTF guide gives starting values, listed on this page, but says they change with the film, powder, garment and amount of ink. Follow your film and powder maker's instructions first and test.
- Epson DTF Film Printing Guide (CMP0437)
- Epson F2270 User's Guide: Precautions when printing on film
- Epson F2270 User's Guide: Required equipment (printing on film)
- Epson F2270 User's Guide: Loading film on the platen
- Epson F2270 User's Guide: Performing post-processing for film
- Epson F2270 User's Guide: Registering and using media settings
- Epson F2270 User's Guide: Overall print quality is poor
- AA support requests about F2270 DTF printing, 2024 to 2026











































































