Machine type
Prestige XL series (L2, XL2, XL2 Pro, XL3, XL4)
DTF Station Prestige R2 Pro
DTF Station Prestige R1
DTF Station Prestige R2 (original)
Prestige X6
DTF Station Prestige A4
DTF Station Prestige A3+ and A3+ R
Epson SureColor G6070 DTF printer
Mimaki TxF300-1600
Mimaki TxF330-800
STS XPD-924D DTF Printer (Mutoh)
STS VJ-628D DTF Printer (Mutoh)
DTF Station Vega S17
STS XpertJet 1682D (XPJ-1682D) 64 inch DTF Printer
STS XPD-724 DTF Printer (Mutoh)
Hotronix Fusion IQ, Air Fusion IQ and Dual Air Fusion IQ
Geo Knight DK20S and DK20SP Digital Knight Swing-Away Presses
DTF Station Maxima and Proxima Dual Heat Presses
Hotronix Auto Open Clam and Hover Heat Press
DTF Station Prisma Auto Heat Press
DTF Station Prisma Dual Heat Press
DTF Station Prisma Swing Heat Press
Insta 718, 728 and 828 Automatic Swing-Away Heat Presses
DTF Station Prisma Sentry Heat Press
Geo Knight DC16 and DC16AP Digital Combo Swing-Away Presses
Geo Knight DK Digital Clamshell Presses: DK20, DK16, DKA Auto, DK8 Label and DK7 Cap
Hotronix Auto Open Cap Press and 360 IQ Hat Press
Hotronix Craft Heat Press 9 x 12
Hotronix Mighty Mug Heat Press
Insta 256 and 288 Manual Swing-Away Heat Presses
Insta 907 Dual Station Shuttle Label Heat Press
Viper MAXX pretreatment machine
Ecofreen Mister-T2 and Mister-T2 Pro pretreatment machines
Pearl Elite and Pearl PTM DTG pretreatment machines
Viper XPT-1000 pretreatment machine
Lawson Silver-Jet and Silver-Jet V2 DTG Pretreat Sprayers
Lawson Zoom-AE DTG pretreatment machine
Viper MINI handheld DTG pretreatment machine
Brand
Prestige XL series (L2, XL2, XL2 Pro, XL3, XL4)
DTF Station Prestige R2 Pro
DTF Station Prestige R1
DTF Station Prestige R2 (original)
Prestige X6
DTF Station Prestige A4
DTF Station Prestige A3+ and A3+ R
DTF Station Aries 124 UV DTF printer
Miro DTF Powder Shakers: Miro 13 Max, 16, 24 and 36
DTF Station Aries 213 and Aries 113 UV DTF printers
Seismo L16R and L24R DTF Powder Shaker and Dryer
Phoenix Air 16x20 DTF Curing Oven
DTF Station Maxima and Proxima Dual Heat Presses
DTF Station Prisma Auto Heat Press
DTF Station Prisma Dual Heat Press
DTF Station Prisma Swing Heat Press
DTF Station Vega S17
DTF Station Prisma Sentry Heat Press
DTF Station Seismo V36R DTF Powder Shaker and Dryer
DTF Station Arc 127 automatic cutter for DTF and UV DTF film
Epson SureColor F2100
Epson SureColor G6070 DTF printer
Epson SureColor F2270
Epson SureColor F3070
Epson SureColor F570
Epson SureColor F170
Epson SureColor F6470 and F6470H
Epson SureColor F6370
Epson SureColor F7200
Epson SureColor P-Series photo printers (P700, P900, P6570, P8570)
Epson SureColor T-Series CAD and technical printers
Epson SureColor S-Series (S40600, S60600, S80600)
Epson F3070 loading T-shirts: grip pad, platen frame, sleeve and grooved platens, and platen height
On the F3070, load cotton shirts on a grip pad covered platen and polyester shirts on a platen without a grip pad, using the platen frame. Slide the hem on from the front, flatten the print area without stretching it, remove lint, and tuck the shirt in so nothing drapes over the movable base. Set the platen position for the garment thickness (P for up to 4 mm on standard platens), and check the height before printing anything 4 mm or thicker.
Pick the platen first
| Garment | Platen | Grip pad? |
|---|---|---|
| Cotton T-shirt | Standard platen, or L, M, S hanger platen | Yes, recommended |
| Polyester T-shirt | Platen without a grip pad, with its frame | No |
| Sleeves | Sleeve platen, with its frame | No |
| Polo or zip-up | Medium grooved platen, with its frame | No |
Change the platen before you change shirt size or print area. Make sure the platen is ejected forward (press the movable base button if not), turn the printer off, lift the old platen straight up, and seat the new one so its shaft drops into the holes. Hanger platens go in with the hanger at the front; the grooved platen goes in with the cutout at the front.
Set the platen position
With Platen Gap on Auto, Epson gives a starting position by garment thickness. Change it with the platen gap lever: loosen the fixing lever, move the gap lever while watching the screen, then tighten the fixing lever. P is the highest position; bigger numbers are lower.
| Thickness | Standard platens | Sleeve or grooved |
|---|---|---|
| 0 to 4 mm | P | 3 |
| 4 to 7 mm | 1 | 4 |
| 7 to 10 mm | 2 | 5 |
| 10 to 13 mm | 3 | 6 |
Thicker garments go lower still; the full table is in Epson's User's Guide. If Platen Gap is set to Manual, use the guide's separate table for media thickness and platen type.
Loading on a grip pad covered platen
-
Get the shirt flat
If the shirt is creased, press it flat on the heat press first. Turn the printer on and check the platen is out front.
-
Slide it on
Slide the hem over the platen from the front and pull the overhanging parts to flatten the print area. Don't stretch it hard: Epson says a stretched shirt prints distorted and the white underbase can show outside the image.
-
Lint and fibers
If the shirt isn't pretreated, take lint off with sticky tape or a roller and press the fibers flat with the hard roller. Loose fibers can stick to the print head.
-
Smooth it with the grip pad tool
Press lightly with the grip pad tool and move it from the edges, up and down and side to side, two or three times. The printer sets height from the highest point, so any ripple lowers quality. On a pretreated shirt, or fabric the tool catches on, put a release sheet such as silicone paper between the tool and the shirt.
-
Tuck in
Tuck the shirt in so it doesn't hang over the movable base.
Loading with the platen frame
-
Remove the frame
Lift the frame off the platen and slide the shirt on from the front (or pass the sleeve platen through the sleeve).
-
Flatten, then refit the frame
Pull the overhanging fabric to flatten the print area and refit the frame. On the sleeve platen, keep side and sleeve seams off the top. On the grooved platen, fit the collar or zipper into the cutout so nothing sticks up above the print surface.
-
Tension and tuck
Remove lint, pull the shirt outside the frame to take out creases and slack, press the frame down so it isn't loose, and tuck the shirt in around it.
Check the height on thick garments
For anything 4 mm or thicker, Epson recommends a check before you send the job. Load the shirt and press the start button. The platen moves into position. If you get a surface error, adjust the platen one position as described in the FAQ, and check again until no error shows.
Still getting height errors or misprints? Text a photo of the loaded platen and the screen to (562) 609-4996.
Watch Epson's video: loading a T-shirt on the F3070 grip pad platen
More videos
Embedded from the manufacturer's official channel.
Common questions
Should I use the grip pad for polyester?
No. Epson says load polyester on a platen without a grip pad, or the pad's fabric can get ink on it.
Which platens can take a grip pad?
The platen supplied with the printer and the optional L, M and S hanger platens. Don't put a grip pad on the XS, sleeve or medium grooved platens.
How do I print polos or zip-up shirts?
Use the medium grooved platen. Leave the square part in for polos so the collar or buttons sit in the cutout. Remove it for zippers.
I get The surface of the media cannot be detected. What now?
If the shirt is loaded correctly, press OK, raise the platen one position and check again.
I get The position of the media surface is too high.
If there's no dust and the shirt is loaded correctly, press OK, lower the platen one position and check again.
- Epson SC-F3000 Series (SureColor F3070) User's Guide (PDF)
- Epson SureColor F3070 support page
- AA support requests about the Epson F3070, 2024 to 2026











































































