Machine type
Prestige XL series (L2, XL2, XL2 Pro, XL3, XL4)
DTF Station Prestige R2 Pro
DTF Station Prestige R1
DTF Station Prestige R2 (original)
Prestige X6
DTF Station Prestige A4
DTF Station Prestige A3+ and A3+ R
Epson SureColor G6070 DTF printer
Mimaki TxF300-1600
Mimaki TxF330-800
STS XPD-924D DTF Printer (Mutoh)
STS VJ-628D DTF Printer (Mutoh)
DTF Station Vega S17
STS XpertJet 1682D (XPJ-1682D) 64 inch DTF Printer
STS XPD-724 DTF Printer (Mutoh)
Hotronix Fusion IQ, Air Fusion IQ and Dual Air Fusion IQ
Geo Knight DK20S and DK20SP Digital Knight Swing-Away Presses
DTF Station Maxima and Proxima Dual Heat Presses
Hotronix Auto Open Clam and Hover Heat Press
DTF Station Prisma Auto Heat Press
DTF Station Prisma Dual Heat Press
DTF Station Prisma Swing Heat Press
Insta 718, 728 and 828 Automatic Swing-Away Heat Presses
DTF Station Prisma Sentry Heat Press
Geo Knight DC16 and DC16AP Digital Combo Swing-Away Presses
Geo Knight DK Digital Clamshell Presses: DK20, DK16, DKA Auto, DK8 Label and DK7 Cap
Hotronix Auto Open Cap Press and 360 IQ Hat Press
Hotronix Craft Heat Press 9 x 12
Hotronix Mighty Mug Heat Press
Insta 256 and 288 Manual Swing-Away Heat Presses
Insta 907 Dual Station Shuttle Label Heat Press
Viper MAXX pretreatment machine
Ecofreen Mister-T2 and Mister-T2 Pro pretreatment machines
Pearl Elite and Pearl PTM DTG pretreatment machines
Viper XPT-1000 pretreatment machine
Lawson Silver-Jet and Silver-Jet V2 DTG Pretreat Sprayers
Lawson Zoom-AE DTG pretreatment machine
Viper MINI handheld DTG pretreatment machine
Brand
Prestige XL series (L2, XL2, XL2 Pro, XL3, XL4)
DTF Station Prestige R2 Pro
DTF Station Prestige R1
DTF Station Prestige R2 (original)
Prestige X6
DTF Station Prestige A4
DTF Station Prestige A3+ and A3+ R
DTF Station Aries 124 UV DTF printer
Miro DTF Powder Shakers: Miro 13 Max, 16, 24 and 36
DTF Station Aries 213 and Aries 113 UV DTF printers
Seismo L16R and L24R DTF Powder Shaker and Dryer
Phoenix Air 16x20 DTF Curing Oven
DTF Station Maxima and Proxima Dual Heat Presses
DTF Station Prisma Auto Heat Press
DTF Station Prisma Dual Heat Press
DTF Station Prisma Swing Heat Press
DTF Station Vega S17
DTF Station Prisma Sentry Heat Press
DTF Station Seismo V36R DTF Powder Shaker and Dryer
DTF Station Arc 127 automatic cutter for DTF and UV DTF film
Epson SureColor F2100
Epson SureColor G6070 DTF printer
Epson SureColor F2270
Epson SureColor F3070
Epson SureColor F570
Epson SureColor F170
Epson SureColor F6470 and F6470H
Epson SureColor F6370
Epson SureColor F7200
Epson SureColor P-Series photo printers (P700, P900, P6570, P8570)
Epson SureColor T-Series CAD and technical printers
Epson SureColor S-Series (S40600, S60600, S80600)
Epson F3070 replacing the head cleaning set, anti-drying caps and air filters, step by step
When the F3070 says a part is at the end of its service life, replace it from the menu so the counter resets: Menu > Maintenance > Replace Maintenance Parts, then Head Cleaning Set, Anti-Drying Cap or Air Filter. The head cleaning set is one wiper unit and two flushing pads, the caps are replaced front and back together, and all three air filters go in at once. The printer won't print until the head cleaning set is replaced.
When each part is due
| Part | What you'll see | What to do |
|---|---|---|
| Head cleaning set | A warning icon in the head cleaning set status, then Head Cleaning Set is at the end of its service life. | Order one at the first warning. Printing stops until it's replaced |
| Anti-drying caps | Anti-Drying Cap is at the end of its service life. | Replace the front and back caps together |
| Air filters | Air Filter is at the end of its service life. | Replace all three filters together |
Use parts made for the F3070. Wear protective eyewear, gloves and a mask, touch something metal first to discharge static, and don't touch circuit boards or any part you aren't replacing. Never move the print head or platen by hand.
If you replace anything before the message appears, always start from Menu > Maintenance > Replace Maintenance Parts. That's what resets the part counter. Have a metal or plastic tray ready for the used parts.
Replacing the head cleaning set
-
Start it from the screen
On the end-of-life message, press OK. If there's no message, go to Menu > Maintenance > Replace Maintenance Parts > Head Cleaning Set. Read the message and press Start. The platen and print head move to the maintenance position.
-
Take out the wiper unit
Open the right side of the printer cover. Hold the tabs on both sides of the wiper unit and lift it straight up. Wrap it in the packaging the new one came in so it doesn't drip.
-
Check the area and fit the new wiper
Look for ink, fluff or dust in the area around the wiper. If any is stuck there, wipe it with a soft cloth soaked in water and wrung out tightly. Insert the new wiper unit.
-
Lift out the flushing pads
Lift the tab on the flushing pad gently. Ink can spray if you raise it too hard. Hold it at an angle until it stops dripping, then set it on the tray.
-
Check the waste liquid port
Look for a hard film of dried waste ink on the waste liquid port. If there is one, clear it with a new wide cleaning stick, pour about 100 ml of pure water into the maintenance kit cup, and pour it into the port. If the water drains slowly, clear more ink and test again. Epson warns that a blocked port can make waste liquid overflow.
-
Fit the new flushing pads
Insert the two hooks on each new pad into the slots and press the tab down until it clicks. Check that both pads are seated. A raised hook can damage the print head.
-
Finish
Bag the old pads in the new pads' packaging, close the right cover, read the message and press Yes. The counter clears.
A buzzer sounds 10 minutes after the head moves, and every 10 minutes after that. Press OK and keep going, but don't leave the head uncapped longer than you need to.
Replacing the anti-drying caps
-
Unpack and start
Unpack the new caps. On the end-of-life screen press Replace Parts, or go to Menu > Maintenance > Replace Maintenance Parts > Anti-Drying Cap, then press Start.
-
Remove both caps
Open the right side of the printer cover. Press on the indents of the hooks and remove the back cap (white) and the front cap (colors). Put them in the new caps' packaging.
-
Fit the new caps
Press each new cap in until it clicks, then remove its protective cover. Epson warns that printing with the cover still on can damage the print head.
-
Close up
Close the right cover and press Done. The platen and head return home.
Replacing the air filters
-
Start it
Press Replace Parts on the message, or go to Menu > Maintenance > Replace Maintenance Parts > Air Filter.
-
Right side
Open the right side of the printer cover, grip the filter's tab and pull it out. Insert the two hooks at the end of the new filter into the holes and press down until the tab clicks. Close the right cover.
-
Left side
Open the left side of the printer cover and replace the other two filters the same way. Close it and press Done. Put the old filters in the new filters' bags.
If a message doesn't clear after replacement, or you see a maintenance request code, text a photo of the screen to (562) 609-4996.
Common questions
What's in the F3070 head cleaning set?
One wiper unit and two flushing pads. Epson says to replace all of them together.
Can I swap the parts early, before the message appears?
Yes, but start it from Menu > Maintenance > Replace Maintenance Parts. If you don't, the counter can't track the parts correctly.
The head cleaning set is due and I don't have one yet. What should I do?
Epson says auto maintenance may not finish and the heads can clog. Turn the printer off and leave it off until the part arrives, and turn it on once a week if that's a week or more.
Do I replace one anti-drying cap or both?
Both, the back cap for white and the front cap for colors, at the same time.
How do I get rid of the old parts?
Epson classes used wipers, flushing pads, caps, air filters and waste ink as industrial waste. Dispose of them under your local rules.











































































