Support
Machine type
Brand
Epson SureColor F6370

Epson F6370 loading sublimation paper: roll adapters, media settings, Custom Paper Setting and the take-up reel

✓ Reviewed by Jason KimUpdated 3 min readFits: F6370
Short answer

On the F6370, set the roll adapters to the roll's core size (2 or 3 inch), fit them to the roll, roll it back along the adapter guide, press the load/remove paper button and feed the paper in with no slack. Lower the adapter holder lock lever, press OK, close the cover and confirm or change the media settings. Save each paper's settings in Paper > Custom Paper Setting (1 to 10), and remove the paper after printing so the rollers don't crease it.

Media edges are sharp. Don't run your hands along them. Load paper just before printing, and don't use creased, curled or wavy paper; it can jam or hit the print head.

Loading a roll

  1. Power on and open up

    Turn the printer on and wait for the load paper message. Open the roll paper cover and lift the adapter holder lock lever. Rest the roll on the roll rest.

  2. Set the adapters to the core

    On both roll paper adapters, slide the size lever to match the roll's core: 3 inch or 2 inch. Lift the lock levers on both adapters.

  3. Fit the adapters

    Push an adapter into each end of the roll until it's fully inserted, then lower both lock levers.

  4. Seat the roll

    Slide the roll right until it touches the adapter guide, then roll it slowly backward along the guide.

  5. Feed the paper

    Press the load/remove paper button, and press OK at the Roll Paper message. Insert the paper into the opening and pull it through with no slack and no folded ends. Turn the adapters to feed it rather than touching the print side.

  6. Lock and load

    Lower the adapter holder lock lever and press OK. The paper feeds in. If the leading edge isn't straight, press OK then the cut/feed media button within five seconds to trim it with the built-in cutter. Close the roll paper cover.

Confirm the media settings

After loading you'll see the current media settings. Choose Keep Settings Above if they match, or Change Settings to edit them. Turn on Remaining Setup if you want the printer to estimate what's left on the roll, then enter the roll length (15 to 3000 feet). When you see Ready, you can print.

Save settings for each paper

Store a set of settings for each paper you use so you can pick it in one step. Load that paper first, then:

  1. Open Custom Paper Setting

    Go to the Paper menu > Custom Paper Setting and pick a number from 1 to 10.

  2. Choose a reference paper

    Select Select Reference Paper, choose Yes, then pick the thickness closest to your paper.

  3. Name it and adjust

    Use Setting Name to name it, adjust any other settings you need, then press pause/cancel to exit.

Then run a head alignment and a paper feed adjustment for that setting. Our F6370 errors and banding guide covers both.

Using the auto take-up reel

  1. Prepare

    Set Auto Cut to Off. Set the reel's Auto switch to Off. Press the cut/feed media button and hold the down arrow until the paper reaches the roll core holders. Always feed with the down arrow, or the paper can twist.

  2. Fit the core

    Unlock both core holders and move them wider than the paper. Align the right holder with the paper's right edge and lock it. Push the core onto the right holder, then fully onto the left. Check the core and paper edges line up, then lock the left holder.

  3. Tape the paper on

    Guide the paper behind the core (printable side in) and tape it on: center first, pulling the center straight, then the sides, pulling each outward. It must lie flat with no gaps.

  4. Wind and switch to Auto

    Feed enough paper to wrap the core once. With Auto off, hold the Manual switch to Backward to wind it on, then set Auto to Backward. Tap both sides of the paper: the tension must be even, or reload.

To take a roll off, set Auto to Off, cut the paper, hold Manual on Backward until it's all wound, unlock the holders and lift the core out. Epson says use two people, one at each end.

Removing paper after printing

Press the load/remove paper button and choose Remove Paper. The printer rewinds the roll. Open the cover, lift the adapter holder lock lever, move the roll to the roll rest, take the adapters off, and store the roll in its original packaging.

Common questions

What widths can the F6370 load?

10 to 44 inches (254 to 1118 mm), Epson says.

Should I leave paper loaded overnight?

No. Epson says to load just before printing and remove it after. The pressure rollers can crease paper left in the printer, and creased paper can jam or touch the head.

Why turn on Paper Size Check?

With it off, the printer assumes 44 inch paper whatever is loaded, so a wide job can print past the edge and get ink inside the printer.

Which way should paper wind on the take-up reel?

Printable side in. Use a core the same width as the paper, with no worn or bent edges.

Do I need to turn off Auto Cut for the take-up reel?

Yes. Epson says using the take-up reel with Auto Cut on causes errors.

Sources
Did this fix it?