Support
Machine type
Brand
Epson SureColor F6470 and F6470H

Epson F6470 loading sublimation paper: media type by paper weight, EMX settings and the auto take-up reel

✓ Reviewed by Jason KimUpdated 3 min readFits: F6470 · F6470H · SC-F6400 Series
Short answer

On the F6470, start loading from the screen (Media, then Start, then Description shows each step), then pick the registered media number for that paper. With no saved settings, choose the media type by paper weight: Thin 50g/m2 for 60 g/m2 or less, Med-Thick 70g/m2 for 61 to 89, Thick 120g/m2 for 90 or more. For the take-up reel, use a core the same width as the paper, tape it on evenly, and wind printed side in.

Before you load

  • Load paper just before you print. Paper left in the printer can crease, wave or curl, then jam or touch the print head.
  • Don't load a roll with uneven left and right edges. Rewind it straight or use another roll.
  • Don't use folded, wrinkled, scuffed, torn or dirty paper, or a roll with frayed ends.
  • Keep paper in its wrapper until you load it, never set it on the floor, and don't carry it pressed against your clothes. Dust and lint on paper cause ink drops and clogs.
  • Media edges are sharp. Don't run your hands along them.

Loading the paper

  1. Follow the on-screen procedure

    When the screen says Load the media., press it, then Start. Press Description to see each step on the panel and follow them. Epson's video shows the same steps.

  2. Pick the media number

    Press Media and choose the registered number that holds the settings for this paper. If you downloaded an EMX file for it, choose that number.

  3. No saved settings? Pick by weight

    Choose an unregistered number. It defaults to Med-Thick 70g/m2. If your paper weighs something else, press Edit, then Media Type, and pick from the table below.

  4. Set the feed options

    Turn on Cut Leading Edge if the front edge isn't straight or cleanly cut. Turn on Prepare for Take-up if you'll use the take-up reel. Press OK and paper feeding starts.

Paper weight Media Type
60 g/m2 or less Thin 50g/m2
61 to 89 g/m2 Med-Thick 70g/m2
90 g/m2 or more Thick 120g/m2

When you register new settings or load an EMX file, run a print head alignment and media feed adjustment once for that paper. Our F6470 banding guide covers both.

Loading the auto take-up reel

You need a take-up core the same width as the paper (no worn or bent edges, which cause uneven tension and banding) and some ordinary adhesive tape.

  1. Set up the holders

    Set the reel's Auto switch to Off. Release the left lock lever and move that holder outside the paper width. Release the right lock lever, align the right holder with the paper's edge, and lock it.

  2. Fit the core

    Put the core on the holders. Make sure the holders are inside the core and the core lines up with the paper edges, then lock the left holder. If the edges don't line up, unlock the right holder and start again.

  3. Tape the paper on

    Check the winding direction and tape the paper to the core: center first, pulling the center straight, then the sides, pulling each outward.

  4. Wind once, then go to Auto

    Press the feed button until there's enough paper for one full wrap. Set the Manual switch to match the winding direction and wind it once around. Set Auto to the same direction.

  5. Check the tension

    Tap both sides of the paper lightly. If one side is slacker, rewind, peel off the tape and redo the taping.

If you turned on Prepare for Take-up, the screen shows a How To... button that walks you through these steps; press Complete when done.

Cutting and removing paper

  • Cutting: with Auto Cut off or the take-up reel in use, open the Cut screen, use the arrow buttons to line up the cut point with the mark inside the printer (don't open the cover), support the paper and press Cut.
  • Take-up roll: set Auto to Off, wind the cut paper on with Manual, unlock the left holder, support the core and lift it off. Use two people.
  • Paper roll: press Media > Start; the paper rewinds and ejects. Open the media cover, raise the roll lock lever, move the roll to the roll rest, release and remove the adapters, and store the roll in its packaging.

Watch Epson's video: loading media on the F6470

More videos

Epson: loading into the F6470 auto take-up reel unit

Embedded from the manufacturer's official channel.

Common questions

Which media type should I pick for my paper?

Go by weight: Thin 50g/m2 for 60 g/m2 or less, Med-Thick 70g/m2 for 61 to 89 g/m2, Thick 120g/m2 for 90 g/m2 or more. A wrong media type can hurt print quality.

What's an EMX file?

An Epson print settings file for a specific paper: ICC profile, passes and resolution for the RIP, plus platen gap and feed tension for the printer. Download it in Epson Edge Print, or with Epson Edge Dashboard if you use another RIP.

What's the narrowest paper I can load?

10 inches (254 mm).

Printed side in or out on the take-up reel?

Epson recommends printed side in. Printed side out can let the paper wander and wind badly misaligned.

How short a piece can the built-in cutter cut?

100 mm (3.94 inches). Anything shorter gets extra feed added, which you trim by hand.

Sources
Did this fix it?