Support
Machine type
Brand
Epson SureColor P-Series photo printers (P700, P900, P6570, P8570)

Epson SureColor P700 and P900 banding, faint colors and clogged nozzles: nozzle check, head cleaning, Power Cleaning and alignment

✓ Reviewed by Jason KimUpdated 2 min readFits: P700 · P900
Short answer

Print a nozzle check first and clean only if it shows gaps. Run up to 3 head cleanings, checking after each one, then turn the printer off for at least 6 hours and try again. Use Power Cleaning only if almost the whole pattern is missing or the gaps won't clear. If the nozzle check is clean but prints are grainy or banded, align the print head and check the Paper Type.

Match your symptom

What you see Likely cause Go to
Bands, faint areas, missing color Clogged nozzles Steps 1 to 4
Nozzle check almost blank Heavy clog Step 4 (Power Cleaning)
Grainy, blurry or crooked lines Print head out of alignment Step 5
Smears on the back Ink on the paper guide rollers Step 6
Bands, clean nozzle check Wrong Paper Type, wrong side up, high speed on Last section

You can't clean the head while any cartridge is expended, and maybe not while one is low. Replace it first. Never turn the printer off during a cleaning cycle.

Step by step

  1. Print a nozzle check

    Load a few sheets of plain paper in the rear paper feeder. On the screen, open the settings icon and select Maintenance > Print Head Nozzle Check > Start. On a computer, the same check is in the printer utility (Windows: right-click the printer icon in the taskbar; Mac: Printers & Scanners > Options & Supplies > Utility).

  2. Read the pattern

    Look for gaps or faint lines. If the pattern is complete, select O and stop: Epson says cleaning uses ink, so only clean when there are gaps. Take a photo of it in case you need to send it to us.

  3. Run a head cleaning

    If there are gaps or the pattern is faint, select X, then Head Cleaning, and follow the screen. Print another nozzle check after each cleaning. Do this up to 3 times.

  4. Rest it, then Power Cleaning

    If 3 cleanings haven't helped, turn the printer off with the power button and leave it for at least 6 hours, then check and clean again. If almost the whole pattern is missing, or it still isn't clear, run Maintenance > Power Cleaning. It uses a lot of ink, so keep it for stubborn clogs. If nozzles are still missing after another 6 hour rest and a cleaning, contact us.

  5. Align the print head

    For grainy or blurry prints, crooked vertical lines or bands that cleaning doesn't fix, load plain paper and select Maintenance > Print Head Alignment > Start. Don't cancel while the patterns print. Pick the best-printed square in each set as the screen asks.

  6. Clean the paper guide

    If ink marks the back of your prints, select Maintenance > Paper Guide Cleaning. Load A3 or A3+ plain paper for the P700, or A2 for the P900, and repeat until the smears stop.

When the head isn't the problem

  • Check the Paper Type matches the paper, and that you loaded it printable side up.
  • Turn off any high speed setting in the driver and pick a higher quality.
  • Old ink can print badly even after cleaning. Epson recommends taking the cartridges out and shaking them gently every six months, using each cartridge within a year of opening, and replacing one that's more than six months old if prints still don't look right.
  • Grainy prints can also come from a low-resolution image. Epson's guide says to raise the image resolution when you enlarge it.

Maintenance box messages

Cleaning sends ink to the maintenance box (part C12C935711). Check its level under Ink Info on the home screen. When the screen asks, replace it by following the on-screen steps. Don't do it while the printer is printing, don't touch the green chip, keep the used box level, and don't reinstall a box that's been out for a long time. A message that the printer's Ink Pad is near or at the end of its life is different: those pads aren't user-replaceable, so contact us.

Common questions

How many cleanings is too many?

Epson says to stop after 3, turn the printer off and wait at least 6 hours before trying again. Each cleaning uses ink and fills the maintenance box.

When should I use Power Cleaning?

When almost the entire nozzle check is missing, or regular cleanings and a 6 hour rest haven't cleared it. It uses a lot of ink.

Why won't the printer let me clean the head?

A cartridge is expended or very low. Replace it first, then clean.

My nozzle check is perfect but I still see bands. Why?

Check the Paper Type and that the paper is printable side up, turn off high speed printing, and run Print Head Alignment.

The screen says the Ink Pad is at the end of its service life. Can I replace it?

No. Epson says the ink pads aren't user-replaceable. Contact us. It's a different part from the maintenance box.

Sources
Did this fix it?