Support
Machine type
Brand
Epson SureColor P-Series photo printers (P700, P900, P6570, P8570)

Epson SureColor T-Series error messages: printer error codes, maintenance requests, ink and maintenance box messages

✓ Reviewed by Jason KimUpdated 3 min readFits: T2170 · T3170 · T5170 · T3170x · T3170M · T5170M · T3770 · T5770 · T7770 · P6570 · P8570
Short answer

Ink, maintenance box, paper setting and network messages on a SureColor T-Series are usually owner fixes: reseat or replace the part, match the paper type, or check the network report. A "Printer error" with a code means a fault the printer can't clear: unplug it at both ends, reconnect and restart. If the same code returns, it needs service, so photograph the code and contact us. A "maintenance request" code means an internal part is wearing out and also needs service.

When something stops the printer, the screen shows a message, and for serious faults a number. Here is what Epson says each common message means and what an owner can do about it. The menus differ slightly: on the T2170 to T5170 family you start from Settings, and on the T3770 to T7770 family from the Menu icon.

Messages you can fix yourself

Message What it means What to do
Cannot recognize ink cartridges A cartridge isn't read Remove and reinsert it. If the message stays, fit a new cartridge. Cartridges should be at room temperature
Ink is low A cartridge is nearly empty Keep a new one ready. You can't print with any slot expended or empty
Maintenance box not recognized Box isn't seated or isn't read Remove and reinsert it, then try a new box
Maintenance box nearing end of life Not enough room for cleaning waste Don't run head cleanings until you replace it
Command Error The job came from the wrong driver Cancel it and print with the driver made for your model
Change paper settings Driver paper type doesn't match the printer Pick the matching paper type on the printer, or use Use Printer Settings in the driver
Motor self adjustment Normal internal adjustment Wait for it to finish. Don't turn the printer off
Recovery Mode A firmware update failed Connect by USB and run the firmware update again
Scanner Error (M models) Scanner lock or connection Release the scanner transport lock and restart both units

Printer error with a number

A message such as Printer error. Turn the power off and on again with a code under it means the printer hit a fault it can't clear by itself, and it stops printing. A loose power cable can also cause it.

  1. Power it down fully

    Turn the printer off. Unplug the power cable from the wall and from the printer.

  2. Reconnect and restart

    Plug both ends back in firmly and turn the printer on. On the T3770, T5770 and T7770, Epson suggests turning it off and on several times.

  3. Write down the code

    If the same message comes back, write down or photograph the code exactly as shown. Don't keep power cycling.

A printer error that survives a restart needs service. Text us a photo of the screen with the code at (562) 609-4996 and we'll take it from there.

Maintenance request or "part needs to be replaced"

This message and its code mean a part inside the printer is near or at the end of its service life. It isn't a maintenance box or cartridge you can swap. Epson says the message stays until the part is replaced, and on the T3770 to T7770 family, continuing to print will eventually cause a printer error. Contact us with the code so we can arrange service before that happens.

Network error codes (E-1 to E-13)

If the printer won't join your network, print a network connection report from General Settings > Network Settings on the T3770 to T7770 (choose Connection Check), or a network status sheet from Settings > General Settings > Network Settings > Network Status on the T2170 to T5170. Common fixes from Epson's tables:

  • E-1: check the network cable and that the router or switch is on. Ethernet and Wi-Fi can't be used at the same time.
  • E-2, E-3, E-7: the printer can't find your network or the password is wrong. Restart the router, move the printer closer, and recheck the password.
  • E-5: the router's security type doesn't match. E-6: the router may be filtering the printer's MAC address.
  • E-8 to E-13: IP address, subnet or gateway problems. Set Obtain IP Address to Auto if your router uses DHCP, or correct the manual addresses.

It stopped printing but shows no error

Check the computer's print queue. When an error happens mid-job, the queue goes to Pause. Resume it in the printer's queue window on Windows or Mac. Also make sure the USB cable is no longer than 10 feet and plugged straight into the computer rather than a hub.

Common questions

What does a printer error code like 0011xx mean?

Epson doesn't publish what each code means for owners. It's a service code. Restart the printer as described, and if the same code returns, send it to us.

Can I keep printing with a maintenance request message?

For a while, but Epson says the message stays until the part is replaced, and on the T3770 to T7770 family a printer error will follow if you keep going.

The printer says it can't recognize a new cartridge. Is it bad?

Reseat it first and make sure it's at room temperature. If the message stays, try another new cartridge before assuming the printer is at fault.

What does Command Error mean?

The job was sent with a driver that doesn't support this printer. Cancel it and print with the correct Epson driver.

How do I see network error codes?

Print the network connection report or network status sheet from the Network Settings menu. The E code is at the top.

Did this fix it?