Machine type
Prestige XL series (L2, XL2, XL2 Pro, XL3, XL4)
DTF Station Prestige R2 Pro
DTF Station Prestige R1
DTF Station Prestige R2 (original)
Prestige X6
DTF Station Prestige A4
DTF Station Prestige A3+ and A3+ R
Epson SureColor G6070 DTF printer
Mimaki TxF300-1600
Mimaki TxF330-800
STS XPD-924D DTF Printer (Mutoh)
STS VJ-628D DTF Printer (Mutoh)
DTF Station Vega S17
STS XpertJet 1682D (XPJ-1682D) 64 inch DTF Printer
STS XPD-724 DTF Printer (Mutoh)
Hotronix Fusion IQ, Air Fusion IQ and Dual Air Fusion IQ
Geo Knight DK20S and DK20SP Digital Knight Swing-Away Presses
DTF Station Maxima and Proxima Dual Heat Presses
Hotronix Auto Open Clam and Hover Heat Press
DTF Station Prisma Auto Heat Press
DTF Station Prisma Dual Heat Press
DTF Station Prisma Swing Heat Press
Insta 718, 728 and 828 Automatic Swing-Away Heat Presses
DTF Station Prisma Sentry Heat Press
Geo Knight DC16 and DC16AP Digital Combo Swing-Away Presses
Geo Knight DK Digital Clamshell Presses: DK20, DK16, DKA Auto, DK8 Label and DK7 Cap
Hotronix Auto Open Cap Press and 360 IQ Hat Press
Hotronix Craft Heat Press 9 x 12
Hotronix Mighty Mug Heat Press
Insta 256 and 288 Manual Swing-Away Heat Presses
Insta 907 Dual Station Shuttle Label Heat Press
Viper MAXX pretreatment machine
Ecofreen Mister-T2 and Mister-T2 Pro pretreatment machines
Pearl Elite and Pearl PTM DTG pretreatment machines
Viper XPT-1000 pretreatment machine
Lawson Silver-Jet and Silver-Jet V2 DTG Pretreat Sprayers
Lawson Zoom-AE DTG pretreatment machine
Viper MINI handheld DTG pretreatment machine
Brand
Prestige XL series (L2, XL2, XL2 Pro, XL3, XL4)
DTF Station Prestige R2 Pro
DTF Station Prestige R1
DTF Station Prestige R2 (original)
Prestige X6
DTF Station Prestige A4
DTF Station Prestige A3+ and A3+ R
DTF Station Aries 124 UV DTF printer
Miro DTF Powder Shakers: Miro 13 Max, 16, 24 and 36
DTF Station Aries 213 and Aries 113 UV DTF printers
Seismo L16R and L24R DTF Powder Shaker and Dryer
Phoenix Air 16x20 DTF Curing Oven
DTF Station Maxima and Proxima Dual Heat Presses
DTF Station Prisma Auto Heat Press
DTF Station Prisma Dual Heat Press
DTF Station Prisma Swing Heat Press
DTF Station Vega S17
DTF Station Prisma Sentry Heat Press
DTF Station Seismo V36R DTF Powder Shaker and Dryer
DTF Station Arc 127 automatic cutter for DTF and UV DTF film
Epson SureColor F2100
Epson SureColor G6070 DTF printer
Epson SureColor F2270
Epson SureColor F3070
Epson SureColor F570
Epson SureColor F170
Epson SureColor F6470 and F6470H
Epson SureColor F6370
Epson SureColor F7200
Epson SureColor P-Series photo printers (P700, P900, P6570, P8570)
Epson SureColor T-Series CAD and technical printers
Epson SureColor S-Series (S40600, S60600, S80600)
Epson SureColor T3770, T5770, T7770, P6570 and P8570 maintenance: nozzle check, maintenance boxes, cap cleaning and cutter
Print a nozzle check before important jobs and clean only the color pairs with gaps. Use Power Cleaning only after several regular cleanings fail. Replace the maintenance box (C13S210115) or borderless boxes (C13S210116) when the screen asks, clean the platen and borderless pad edges monthly, and use Epson cleaning sticks around the head and caps only for a clog that cleaning won't clear. Replace the cutter (C13S210117) when cuts get ragged.
This covers routine upkeep on the SureColor T3770, T5770, T7770, P6570 and P8570. Everything here is in Epson's owner manual. For the cap and print head cleaning you need Epson cleaning sticks (C13S090013).
Match your symptom
| Symptom | What to do |
|---|---|
| Maintenance box message | Replace the box the screen names |
| Borderless maintenance box message | Replace that borderless box |
| Gaps in the nozzle check | Head cleaning, then Power Cleaning |
| Clog that cleanings don't clear | Wipe around the print head and clean the cap area |
| Ink or lint marks on prints | Clean the platen and borderless pad edges |
| Ragged cuts | Replace the cutter (C13S210117) |
Nozzle check and cleaning
-
Check
Load paper with the correct paper type set, then select Maintenance > Print Head Nozzle Check > Start. Epson suggests a check before each job or after the printer has sat unused.
-
Clean only the colors you need
Select Maintenance > Print Head Cleaning, pick the color pairs with gaps and select OK. A cycle takes about 4 to 10 minutes, up to 28. Never turn the printer off during a cleaning.
-
Power Cleaning if gaps remain
After several cleanings, select Maintenance > Power Cleaning and choose the nozzle pairs. It uses a lot of ink. Then leave the printer off overnight and check again.
The printer also checks its own nozzles at power on and before printing and cleans automatically. You can change that in General Settings > Printer Settings > Auto Cleaning. If prints are still grainy or banded after cleaning, run the print head alignment and paper feed adjustment from the Maintenance menu.
Replace the maintenance box
-
Check which box
The screen tells you which box is due. Maintenance > Replace Maintenance Box > Maintenance Box > How To shows the steps.
-
Swap it
Don't do this while printing. Open the maintenance box cover and pull the old box out by its handle without tilting it. Don't touch the chip on the new box.
-
Seal and finish
Seal the old box in the bag from the new one before you tilt it. Push the new box in firmly and close the cover.
The borderless boxes catch ink from borderless printing. To reach one, lower the paper support to position A, pull out the paper output flap, then raise the support to position C. Slide the box out level, bag it, push the new one in and return the support to A. Don't reuse any box that has been out of the printer for a long time, because Epson says it won't absorb ink any more.
Wipe around the print head and clean the caps
Do this only when cleanings don't clear a clog. Remove any paper, touch something metal to discharge static, and always use a new cleaning stick. Never use alcohol or other solvents on the caps, and never move the head by hand.
-
Around the head
Select Maintenance > Cleaning the Maintenance Parts > Wiping the Print Head > Start. Open the maintenance cover and wipe away ink, lint and dirt around the head. Repeat from the rear maintenance cover behind the port cover, close everything and select Done.
-
Around the caps
Select Maintenance > Cleaning the Maintenance Parts > Wiping around the Cap. Open the covers and remove the protective piece. With fresh sticks, wipe the anti-drying caps, the wiper and the suction caps and their guides without pressing hard. Lift out lint with the stick tip or tweezers, refit the protective piece, close the covers and select OK.
Monthly cleaning
Once a month, unplug the printer and wipe the outside with a soft cloth, using water with a little neutral detergent for stubborn dirt. Then, with the power off for a minute, open the front covers and wipe the platen from top to bottom with a lint-free cloth. Push paper dust into the holes with a toothpick and clear the edges of the borderless pads with a cotton swab. Don't touch the rollers or ink tubes.
Replace the cutter
Remove all paper, then select Maintenance > Replace Auto cutter blade > Start. Open the maintenance cover, loosen the Phillips screw and lift the old cutter out. Install the new cutter with its protective material still on and tighten the screw firmly. Close the cover and select OK. The printer cuts off the protective piece, which you then remove.
If a nozzle stays missing after a Power Cleaning and an overnight rest, stop running cleanings and text us a photo of the nozzle check at (562) 609-4996.
Watch Epson's video: maintenance on the T3770, T5770, T7770, P6570 and P8570
More videos
Embedded from the manufacturer's official channel.
Common questions
How long does a head cleaning take?
Epson says about 4 to 10 minutes, and up to 28 minutes depending on the nozzles and how many color pairs you pick.
Can I use alcohol on the caps?
No. Epson says organic solvents like alcohol can damage the print head. Use dry, new cleaning sticks.
What are the borderless maintenance boxes for?
They absorb the ink that goes past the paper edge in borderless printing. They're separate from the main maintenance box.
Can I put an old maintenance box back in?
Not if it has been out of the printer and exposed to air for a long time. It won't absorb any more ink.
How often should I clean the inside?
Epson suggests cleaning the platen and borderless pad edges about once a month.
- Epson SureColor P6570/P8570/T3770/T5770/T7770 Series User's Guide (PDF)
- Epson America: SureColor P-Series & T-Series Performing Maintenance Procedures
- AA support requests about T-Series and P-Series maintenance, 2024 to 2026











































































