Support
Machine type
Brand
Epson SureColor P-Series photo printers (P700, P900, P6570, P8570)

Epson SureColor P700 and P900 loading paper: rear feeder, front fine art feeder, roll paper and feeding problems

✓ Reviewed by Jason KimUpdated 3 min readFits: P700 · P900
Short answer

Load photo and plain paper as a stack in the rear paper feeder, and fine art paper or poster board one sheet at a time in the front paper feeder, with clear space behind the printer. The P700 takes roll paper as standard, and the P900 needs Epson's optional roll media adapter. Most feeding problems come from curled or damp paper, too many sheets, the front feeder left extended, or dusty rollers.

Match your symptom

What you see Likely cause Fix
Sheets won't feed or double-feed Sheets stuck together, too many loaded, or dusty rollers Fan the stack, load fewer, clean the paper guide
Thick paper won't go in Wrong feeder, or paper curled or at an angle Use the front paper feeder, one flat sheet, fed straight
Roll won't feed Ragged or curled leading edge Cut the end straight, uncurl it, reload
Paper stops before ejecting Paper size setting doesn't match the paper Cancel, eject, set the right size
Wrinkled prints Damp or thin paper, or wrong paper type Fresh paper and the right Paper Type

Which feeder for which paper

  • Rear paper feeder: plain paper and most glossy, semi-gloss, luster and matte photo papers, loaded as a stack. Don't stack above the arrow mark on the edge guide.
  • Front paper feeder: fine art papers (Velvet Fine Art, Hot Press, Cold Press, Exhibition Fiber, Watercolor and similar) and poster board, one sheet at a time. Epson lists poster board from 0.02 to 0.059 inch (0.51 to 1.5 mm) thick.
  • Roll paper: the P700 takes 8.27 to 13 inch rolls on a 2 inch core, up to 3.31 inches across. The P900 needs Epson's optional roll media adapter and takes 8.27 to 17 inch rolls on a 2 or 3 inch core, up to 5.91 inches across.

Load the rear paper feeder

  1. Open the feeder

    Turn the printer on. Open the paper support, pull up the extensions and open the front cover.

  2. Load the stack

    Put the paper in glossy or printable side up and short edge first, against the right side. Slide the edge guide against the paper, but not too tightly.

  3. Tell the printer what you loaded

    When the screen asks, pick the paper size and Paper Type. The Paper Type should match the paper's name (for example Prem. Glossy for Premium Photo Paper Glossy).

Load the front paper feeder (fine art and poster board)

  1. Leave room behind the printer

    The sheet passes out the back while it loads. Epson asks for at least 13 inches (330 mm) of clear space behind a P700 and 16 inches (405 mm) behind a P900.

  2. Choose the feeder on screen

    Select Paper Setting, then Front Paper Feeder - Fine Art or Front Paper Feeder - Poster Board, and pull out the front paper feeder as shown.

  3. Load one sheet

    Insert a single flat sheet, printable side up and short edge first, straight rather than at an angle. Follow the screen until the printer pulls it in, then pick the size and Paper Type.

Push the front paper feeder back in when you print from the rear feeder or from a roll. Epson says to extend it only for fine art paper or poster board, or feeding problems follow.

Load and cut roll paper

  1. Start from the screen

    Select Paper Setting > Roll Paper and pull out the roll paper unit as the screen shows. On a P900, the roll media adapter must be installed first.

  2. Load the roll

    Follow the on-screen steps, then choose the size and Paper Type. If the roll won't feed, cut the leading edge straight across and roll it backward to take out the curl, then load it again.

  3. Cut the print off

    When printing finishes, select Cut/Eject, then Cut and Eject. The printer prints a cut line and feeds the paper. Cut along the line with scissors, select Done and the paper feeds back.

  4. Store the roll

    To remove the roll (on the P900, open the roll paper unit first), take it out and keep it in its original packaging, away from heat, humidity and direct sunlight.

If paper still won't feed

  • Use new, flat paper that isn't damp, curled, creased, too thin or too thick, and check the packet for its own loading instructions.
  • Load cut sheets in the rear feeder vertically (short edge first), and never more than the recommended number of sheets.
  • If the rollers have picked up paper dust they lose grip. Run Maintenance > Paper Guide Cleaning with plain paper loaded.
  • If a sheet doesn't fully eject, cancel the job on the control panel, use the option to cut or eject the paper, remove what's left and pick the right size before you reprint.

Still jamming or a sheet stuck inside? Don't pull hard on it. Text us a photo or short video at (562) 609-4996.

Watch Epson's video: loading fine art paper in the P700/P900 front paper feeder

More videos

Epson: loading fine art paper in the P700/P900 rear paper feeder
Epson: loading roll paper in the SureColor P700
Epson: loading roll paper in the SureColor P900
Epson: loading paper in the P700/P900 rear paper feeder

Embedded from the manufacturer's official channel.

Common questions

Can I print roll paper on the P900 straight out of the box?

No. Epson says the P900 needs the optional roll media adapter (C12C935221) for roll paper. The P700 takes rolls without it.

How wide a roll can I use?

Epson lists 8.27 to 13 inch rolls for the P700 and 8.27 to 17 inch rolls for the P900.

Why does my fine art paper come out the back while it loads?

That's how the front paper feeder works. Epson asks for 13 inches of space behind a P700 and 16 inches behind a P900.

Does the P700 or P900 cut roll paper by itself?

No. Select Cut/Eject, then Cut and Eject. The printer prints a cut line, and you cut along it with scissors.

Do I have to change the Paper Type every time?

Pick it whenever you load a different paper. A wrong Paper Type can cause banding, smears, wrinkles and wrong colors.

Sources
Did this fix it?