Support
Machine type
Brand
Epson SureColor P-Series photo printers (P700, P900, P6570, P8570)

Epson SureColor P700 and P900 setup: first ink charge, driver install, Epson Print Layout and Wi-Fi, USB or Ethernet connection

✓ Reviewed by Jason KimUpdated 3 min readFits: P700 · P900
Short answer

Remove all packing, power on, shake and install the ten cartridges, and let the printer charge for about 15 minutes without turning it off or opening covers. Don't plug in USB first. Download the software package from Epson's support page and choose Wireless, USB or Wired at the Select Your Connection screen. Epson Print Layout is a free extra for photo printing.

Before you start

  • Pick a sturdy, level spot near an outlet you can reach, away from direct sunlight, heat and rapid temperature or humidity changes. The P700 weighs about 30 lb and the P900 about 35 lb, and all four rubber feet must sit on the surface.
  • Don't connect the USB cable to your computer yet. The software tells you when.
  • You need an internet connection to download the software, and a USB 2.0 or 3.0 cable or an Ethernet cable if you won't use Wi-Fi. Neither cable is in the box.

Unpack and charge the ink

  1. Remove all packing

    Take off every piece of tape and protective material, including inside the front and printer covers and behind the rear paper feeder and port cover. Don't touch the ink tube inside.

  2. Power on and set up the screen

    Connect the power cable, press the power button, raise the control panel if needed, and choose your language, date and time.

  3. Install the ink

    Open the front and printer covers. Shake each cartridge gently about 15 times, then unpack it. Epson warns not to touch the areas shown on the Start Here sheet, or the cartridge may not work. Push each one into its color slot until it clicks, then close both covers.

  4. Let it charge

    When the screen asks, select OK to start charging. It takes about 15 minutes. Don't turn the printer off, load paper or open a cover until the screen says charging is complete, or you'll waste ink.

The cartridges that come with the printer are mostly used up filling the system, so the levels will look low right after setup. That's normal. Have replacement cartridges ready, and keep the spare maintenance box that comes in the box.

Install the software and choose a connection

  1. Download the package

    On the computer, go to epson.com/support/p700 or epson.com/support/p900 and download the product software package. If Windows shows a Found New Hardware screen, click Cancel and unplug the USB cable.

  2. Run the installer

    Follow the screens. At Select Your Connection, choose Wireless connection, Direct USB connection or Wired network connection. For wireless, the installer usually sets up Wi-Fi itself. If it can't, enter your network name (SSID) and password.

  3. Add Epson Print Layout (optional)

    Epson Print Layout is Epson's free photo printing tool. It puts the application, color and driver settings in one window with a live preview, and runs on its own or as a Photoshop plug-in. Download it from the same support page.

Connect from the printer's screen

  • Wi-Fi: select the network icon, then Wi-Fi (Recommended) > Start Setup or Change Settings > Wi-Fi Setup Wizard. Pick your network and type the password. It's case sensitive.
  • WPS: choose Push Button Setup (WPS), then hold the WPS button on your router until its light flashes. You have 2 minutes.
  • Wi-Fi Direct: choose Wi-Fi Direct > Start Setup to connect without a router. Up to 8 devices can connect.
  • Wired: choose Wired LAN Connection Method > Start Setup, which turns Wi-Fi off, then plug an Ethernet cable from the printer to your router.

If it won't connect or print

  • Print a connection report (General Settings > Network Settings > Connection Check). It lists the problem and what to try.
  • Make sure the computer and printer are on the same network, and not on a guest network.
  • Moving from USB to Wi-Fi, or to a new router? Epson says to uninstall the printer software and install it again from the support page.
  • If the print head stops moving or making noise and charging hasn't finished after about 5 minutes, turn the printer off and on again. If it's still charging after that, contact us.
  • Check for printer software updates with EPSON Software Updater.

Stuck? Text us a photo of the screen or the connection report at (562) 609-4996.

Watch Epson's video: connecting the P700/P900 to Wi-Fi, Wi-Fi Direct and wired networks

More videos

Epson: unpacking the P700/P900 and installing the ink
Epson: unpacking and setting up the SC-P700 and SC-P900
Epson: P700/P900 changing Windows driver settings
Epson: when the automatic Wi-Fi connection fails (SC-P700/SC-P900)

Embedded from the manufacturer's official channel.

Common questions

Why do my ink levels look low on a brand-new printer?

Epson says the setup cartridges are mainly used to fill the ink system. That's normal. Have replacement cartridges ready.

How long does the first ink charge take?

About 15 minutes. Don't turn the printer off, load paper or open covers until the screen says it's complete.

Does the printer come with a USB cable?

No. Use a USB 2.0 or 3.0 cable, or an Ethernet cable for a wired network. Epson notes that other cables can slow printing.

Can I print from my phone without a router?

Yes. Wi-Fi Direct lets up to 8 devices connect to the printer directly.

I switched from USB to Wi-Fi and now it won't print. What do I do?

Epson says to uninstall the printer software and install it again from the support page, choosing the wireless connection.

Sources
Did this fix it?