Support
Machine type
Brand
Epson SureColor T-Series CAD and technical printers

Epson SureColor T3170, T5170 and T2170 banding or faint prints: nozzle check, head cleaning, maintenance box and cutter

✓ Reviewed by Jason KimUpdated 3 min readFits: T2170 · T3170 · T5170 · T3170x · T3170M · T5170M
Short answer

Print a nozzle check (Settings > Maintenance > Print Head Nozzle Check) and clean only if lines are broken. Run up to three head cleanings, checking after each. If gaps remain, run one Powerful Cleaning, then turn the printer off overnight and check again. Replace the maintenance box (C13S210057) when the screen asks, and the cutter (C13S210055) when cuts get ragged.

Match your symptom

Symptom Likely cause Fix
Faint print or light and dark bands Clogged nozzles Nozzle check, then head cleaning
Still gaps after three cleanings Stubborn clog Powerful Cleaning, then leave it off overnight
Grainy, blurry or misaligned lines Head or feed out of adjustment Print Quality Adjustment
Ink smears on the paper Ink on the feed rollers Paper Guide Cleaning or a roll feed
Message that the maintenance box is full or nearly full Box has absorbed its limit of waste ink Replace the maintenance box
Paper doesn't cut cleanly Dull cutter Replace the cutter blade

Check the nozzles first

Cleaning uses ink, so Epson says to clean only when print quality drops, and to check before you clean.

  1. Load paper

    Make sure roll paper or a cut sheet is loaded.

  2. Print the pattern

    Select Settings > Maintenance > Print Head Nozzle Check, then Start. From a computer, open the printer utility and choose Nozzle Check.

  3. Read it

    If every line is solid, you're done. If lines are broken or faint, choose the option to clean the head.

Clean the print head

  1. Run a head cleaning

    Select Settings > Maintenance > Head Cleaning > Start. Don't open any cover or turn the printer off while it runs.

  2. Check again

    When it finishes, choose Yes to print another nozzle check. Repeat the cleaning and check if needed, up to three times.

  3. Run a Powerful Cleaning

    If three cleanings don't help, select Settings > Maintenance > Powerful Cleaning > Start. It uses a lot of ink. Print a nozzle check afterward.

  4. Rest it overnight

    If nozzles are still clogged, turn the printer off and leave it off overnight, then check again.

You can't clean the head when a cartridge is expended, and maybe not when one is low. Replace it first. On the T3170x, Epson adds one more step after the overnight rest: Power Ink Flushing, which replaces all the ink in the tubes. Run it only right after you fill every tank completely, and expect it to use up a lot of the maintenance box.

If nozzles are still missing after all of this, stop cleaning. More cleanings just fill the maintenance box. Text us a photo of the nozzle check at (562) 609-4996.

Fix grainy prints and misaligned lines

Select Settings > Maintenance > Print Quality Adjustment with the right paper type set. You need at least 16.5 inches of roll paper, two A3 or A4 sheets in the auto sheet feeder, or one A2 sheet in the single-sheet slot. Pick the best pattern in each set when the screen asks. If ink smears on prints from the sheet feeder, load a few plain sheets and run Paper Guide Cleaning until a sheet comes out clean. For roll paper, use Feed/Cut Paper and hold Forward until the paper comes out clean, then cut it.

Replace the maintenance box

The box collects ink used in cleaning. When it's near the end of its life, Epson says not to run head cleanings until you replace it. All of these models use box C13S210057.

  1. Open the cover

    Open the maintenance box cover on the back. You can watch the steps on screen at Settings > Maintenance > Replace Maintenance Box > See Guide.

  2. Swap the box

    Pull the old box out without tilting it. Don't touch the chip on the new box. Line up its groove with the rails and push it all the way in.

  3. Seal the old one

    Put the used box in the bag that came with the new one, seal it and close the cover.

Replace the cutter blade

These models use cutter C13S210055 and you need a Phillips screwdriver. Select Settings > Maintenance > Replace Cutter > Start and open the cutter cover. Loosen the screw, remove the old cutter and bag it. Fit the new one on its pins and tighten the screw firmly, or cuts can come out crooked. Peel off only the protective material Epson shows, leave the protective piece on, then select OK. The printer cuts the protective piece off. Take it out and close the cover.

Common questions

How many head cleanings should I run?

Epson says up to three in a row, with a nozzle check after each. If that doesn't help, run one Powerful Cleaning.

Why won't the printer let me run a cleaning?

A cartridge may be expended or low, or the maintenance box may be near the end of its life. Replace whichever the screen names first.

Can I reuse a maintenance box from another printer?

Don't. Swap in a new box and seal the old one in the bag that comes with the new one.

My lines are straight but the print looks grainy. Is that a clog?

Not always. Run Print Quality Adjustment with the correct paper type selected.

When should I use Power Ink Flushing on the T3170x?

Only after head cleanings, a Powerful Cleaning and an overnight rest haven't worked, and only right after you fill all the tanks.

Did this fix it?