Machine type
Prestige XL series (L2, XL2, XL2 Pro, XL3, XL4)
DTF Station Prestige R2 Pro
DTF Station Prestige R1
DTF Station Prestige R2 (original)
Prestige X6
DTF Station Prestige A4
DTF Station Prestige A3+ and A3+ R
Epson SureColor G6070 DTF printer
Mimaki TxF300-1600
Mimaki TxF330-800
STS XPD-924D DTF Printer (Mutoh)
STS VJ-628D DTF Printer (Mutoh)
DTF Station Vega S17
STS XpertJet 1682D (XPJ-1682D) 64 inch DTF Printer
STS XPD-724 DTF Printer (Mutoh)
Hotronix Fusion IQ, Air Fusion IQ and Dual Air Fusion IQ
Geo Knight DK20S and DK20SP Digital Knight Swing-Away Presses
DTF Station Maxima and Proxima Dual Heat Presses
Hotronix Auto Open Clam and Hover Heat Press
DTF Station Prisma Auto Heat Press
DTF Station Prisma Dual Heat Press
DTF Station Prisma Swing Heat Press
Insta 718, 728 and 828 Automatic Swing-Away Heat Presses
DTF Station Prisma Sentry Heat Press
Geo Knight DC16 and DC16AP Digital Combo Swing-Away Presses
Geo Knight DK Digital Clamshell Presses: DK20, DK16, DKA Auto, DK8 Label and DK7 Cap
Hotronix Auto Open Cap Press and 360 IQ Hat Press
Hotronix Craft Heat Press 9 x 12
Hotronix Mighty Mug Heat Press
Insta 256 and 288 Manual Swing-Away Heat Presses
Insta 907 Dual Station Shuttle Label Heat Press
Viper MAXX pretreatment machine
Ecofreen Mister-T2 and Mister-T2 Pro pretreatment machines
Pearl Elite and Pearl PTM DTG pretreatment machines
Viper XPT-1000 pretreatment machine
Lawson Silver-Jet and Silver-Jet V2 DTG Pretreat Sprayers
Lawson Zoom-AE DTG pretreatment machine
Viper MINI handheld DTG pretreatment machine
Brand
Prestige XL series (L2, XL2, XL2 Pro, XL3, XL4)
DTF Station Prestige R2 Pro
DTF Station Prestige R1
DTF Station Prestige R2 (original)
Prestige X6
DTF Station Prestige A4
DTF Station Prestige A3+ and A3+ R
DTF Station Aries 124 UV DTF printer
Miro DTF Powder Shakers: Miro 13 Max, 16, 24 and 36
DTF Station Aries 213 and Aries 113 UV DTF printers
Seismo L16R and L24R DTF Powder Shaker and Dryer
Phoenix Air 16x20 DTF Curing Oven
DTF Station Maxima and Proxima Dual Heat Presses
DTF Station Prisma Auto Heat Press
DTF Station Prisma Dual Heat Press
DTF Station Prisma Swing Heat Press
DTF Station Vega S17
DTF Station Prisma Sentry Heat Press
DTF Station Seismo V36R DTF Powder Shaker and Dryer
DTF Station Arc 127 automatic cutter for DTF and UV DTF film
Epson SureColor F2100
Epson SureColor G6070 DTF printer
Epson SureColor F2270
Epson SureColor F3070
Epson SureColor F570
Epson SureColor F170
Epson SureColor F6470 and F6470H
Epson SureColor F6370
Epson SureColor F7200
Epson SureColor P-Series photo printers (P700, P900, P6570, P8570)
Epson SureColor T-Series CAD and technical printers
Epson SureColor S-Series (S40600, S60600, S80600)
Epson SureColor T3170, T5170 and T2170: loading roll paper and cut sheets, rolls that won't fit, and clearing jams
These printers take roll paper on a 2-inch core only, up to 4.33 inches across and 6.61 lb, and at least 13 inches wide (8.27 inches on the T3170x). A 3-inch core roll won't fit. Load the roll with the leading edge facing you, push both paper stops tight against it, seat the black end on the right and feed the edge in until it beeps. For jams, cut the roll at the feed slot, pull the paper out from the front, restart and reload.
Will your roll fit?
The T2170, T3170 and T5170 are fussy about roll size. If a roll won't go on the spindle or won't sit in the holder, check it against Epson's limits first.
| Spec | 24-inch models | 36-inch models |
|---|---|---|
| Core | 2 inch only | 2 inch only |
| Roll width | 13 to 24 in (T3170x: 8.27 to 24 in) | 13 to 36 in |
| Outside diameter | Up to 4.33 in | Up to 4.33 in |
| Roll weight | Up to 6.61 lb | Up to 6.61 lb |
| Paper thickness | 0.002 to 0.008 in | 0.002 to 0.008 in |
The 24-inch models are the T2170, T3170, T3170x and T3170M. The 36-inch models are the T5170 and T5170M. Epson says these printers don't support 3-inch core rolls, so a long roll made for a bigger plotter usually won't fit. Buy rolls on a 2-inch core within the diameter above.
Match your symptom
| Symptom | Likely cause | Fix |
|---|---|---|
| Roll won't fit | 3-inch core, or too wide or too big around | Use a 2-inch core roll within the specs above |
| Roll won't feed | Ragged, curled or bent leading edge | Cut the end straight, roll it back to uncurl, reload |
| Paper skews or jams | Gap between the roll and a paper stop | Push both stops tight against the roll |
| Wrinkles while printing | Back tension too low | Set Back Tension to High or Extra High |
| Cut sheet won't go in | Sheet curled, or roll paper still loaded | Flatten the sheet and remove the roll first |
Load roll paper
-
Prepare the roll
Take off any tape and protective paper and make sure the end is cut straight across. Check that Load paper is on the home screen.
-
Take out the spindle
Open the cut sheet cover, release the central lock and open the roll paper cover. Lift out the spindle and pull off the clear paper stop.
-
Put the roll on the spindle
Slide the spindle into the core with the leading edge of the paper facing you. Push the fixed stop and then the clear stop against the roll so there is no gap on either side.
-
Seat it in the printer
Drop the spindle in with the black end on the right.
-
Feed the paper
Push the leading edge into the paper feed slot until the printer beeps. Keep the edge straight, or you can get a skew error or a jam. Close both covers.
-
Set the paper type
Choose the paper type on the screen and, if you track it, the amount left on the roll.
On the T5170, raise the B1 width paper support only when you print on B1 paper (27.8 x 39.4 in) and lower it for every other size, or prints can be scuffed.
Cut and remove the roll
Auto Cut cuts after each page. Epson doesn't recommend the built-in cutter for canvas or synthetic paper because it dulls the blade. For those, turn Auto Cut off in the driver (Advanced > Roll Paper Option > Auto Cut) or on the printer (Advanced Media Setting > Auto Cut > Off). Then use Feed/Cut Paper to move the paper and cut it with scissors.
When you finish, open the covers and select Remove. The roll rewinds by itself. Lift out the spindle, take the roll off, put the clear stop back on the spindle and return the spindle to the printer. Store the roll in its box on its end, never on its edge, where it can get a flat spot.
Load cut sheets
- One sheet at a time: remove the roll, close the auto sheet feeder and take off the output tray. Select Paper Setting > Cut Sheet (1 sheet), open the cut sheet cover, and feed the sheet printable side up, short edge first, lined up with the right edge marks, until it beeps. Then pick the paper type and size.
- Auto sheet feeder: holds up to 50 sheets of plain paper in Letter, Legal, A4 or A3 (5 sheets of other types). The roll can stay loaded. Pull out the supports, slide the edge guides out, load the paper printable side up and slide the guides in to touch it.
Clear a paper jam
-
Cut the roll free
Open the cut sheet cover and the roll paper cover and cut the paper above the feed slot. Close the covers.
-
Pull out the paper
Remove the jammed paper from the front. Open the front cover and take out anything left inside. Don't touch the print head.
-
Restart and reload
Close the cover, turn the printer off and on, cut the roll edge straight and reload it.
A cut sheet jam is the same minus the roll: pull it out from the front, check under the front cover, restart and reload. If paper keeps jamming in the same spot, text us a photo or short video at (562) 609-4996.
Watch Epson's video: loading paper in a SureColor T-Series printer
Embedded from the manufacturer's official channel.
Common questions
Can I use a 3-inch core roll with an adapter?
Epson says these models don't support 3-inch core media. Use 2-inch core rolls.
Why does my roll skew or jam right after loading?
Usually the end isn't cut straight, the edge is bent, or there's a gap between the roll and one of the paper stops. Cut the end straight and push both stops tight.
Can I leave the roll loaded and print from the sheet feeder?
Yes, with the auto sheet feeder. Pick the paper source in the driver. For single cut sheets you have to take the roll out first.
My paper wrinkles as it prints. What setting helps?
Raise Back Tension to High or Extra High in the roll's Advanced Media Setting menu.
Should I cut canvas with the built-in cutter?
Epson doesn't recommend it because it dulls the blade. Turn Auto Cut off and cut by hand.
- Epson SureColor T2170/T3170/T5170 User's Guide (PDF)
- Epson SureColor T3170x User's Guide (PDF)
- Epson SureColor T3170M/T5170M User's Guide (PDF)
- AA support requests about T-Series roll paper that wouldn't fit, 2024 to 2026











































































