Support
Machine type
Brand
Epson SureColor P-Series photo printers (P700, P900, P6570, P8570)

Epson SureColor T3770, T5770, T7770, P6570 and P8570: loading roll paper, cut sheets and poster board

✓ Reviewed by Jason KimUpdated 3 min readFits: T3770 · T5770 · T7770 · P6570 · P8570
Short answer

These printers take 2- or 3-inch core rolls up to 6.69 inches across and 27.55 lb (fit the core adapters for 3-inch cores). Lower the paper support to position A, mount the roll with both stops flush, seat the black stop on the right, lock the lever, choose the paper type and the printer feeds it. Cut sheets and poster board go in the front or back slot with the paper support at position B.

These steps are for the newer 24-, 36- and 44-inch printers: the SureColor T3770, T5770 and T7770 CAD printers and the P6570 and P8570 photo printers. They share one Epson manual. Models ending in D or DR have a second roll (Roll 2). The E models have one roll, and Roll 1 shows as Roll on the screen.

Will your roll fit?

Spec Limit
Core 2 inch or 3 inch (fit the core adapters for 3 inch)
Outside diameter Up to 6.69 in
Roll weight Up to 27.55 lb
Thickness 0.003 to 0.03 in
Width Up to 24 in (T3770, P6570), 36 in (T5770) or 44 in (T7770, P8570). Epson lists the exact supported widths in the manual

Load Roll 1

  1. Prepare the roll

    Remove tape and protective paper and cut the end straight across. On the home screen select the empty roll area, then Roll 1 (or Roll) and OK.

  2. Lower the paper support

    Lift the paper support lock lever and move the support to position A, the lowest. Close the paper output flap if it's open.

  3. Take out the spindle

    Pull the roll holder lock lever all the way up, lift out the spindle and remove the clear paper stop.

  4. Set the core size

    For a 2-inch core, take the core adapters off both stops. For a 3-inch core, fit them, matching the triangle marks, until the tabs click.

  5. Mount the roll

    Slide the spindle in with the leading edge facing you. Push the fixed stop and the clear stop against the roll so both sit flush with no gap.

  6. Seat and lock it

    Place the spindle in the grooves with the black stop on the right and push the lock lever down.

  7. Set the paper

    Select Paper Setting > Roll 1 > Paper Type and choose the paper you loaded. To track what's left, turn on Remaining Amount Management and enter the roll length. If you don't choose within 90 seconds, the printer uses what's shown.

  8. Let it feed

    Select OK. The paper feeds itself. If it doesn't, or Auto Loading is off, turn the roll gently and slide the edge into the slot until you hear a sound.

Roll 2 loads the same way into its drawer unit, with the paper output tray in position A. Don't pull out the Roll 2 unit while paper is loaded in it, or the paper can wrinkle when you slide it back.

Use non-Epson media? Epson says to check the media maker's site for the right media type, or create a custom paper setting with Epson Media Installer or the control panel. The wrong paper type is a common cause of scuffing and banding.

Remove a roll

Select Paper Setting > Roll 1 > Remove, or press the Roll 1 release button. The roll rewinds. If Remaining Amount Management is on, the printer prints a barcode on the leading edge so it can set the type and length next time. Unlock the holder, lift the roll out, put the spindle back and store the roll on its end in its box.

Load cut sheets or poster board

First choose front or back feeding in General Settings > Printer Settings > Paper Source Settings > Cut Sheet/Poster Board Slot. Remove any roll paper, then select Cut Sheet > OK and set the paper support to position B, the middle. Feed from the back lined up with the left line, or from the front lined up with the right edge, printable side up. Sheets shorter than 11.69 inches must pass under the internal rollers. Set the paper size, then OK. Sheets can be up to 0.03 inch thick and poster board 0.031 to 0.059 inch.

If paper won't feed or jams

  • Cut a ragged or curled end straight and roll it backward to flatten it, then reload.
  • Feed poster board in straight, not at an angle.
  • If paper feeds crooked, turn on Detect Paper Skew in Printer Settings.
  • If paper doesn't eject properly, lower the Paper Suction setting for that paper type.
  • Roll marks from automatic feeding: turn Auto Loading off and feed by hand.
  • For a jam, cut the roll at the feed area, open the covers, slide the head gently aside, pull out the paper and check behind the rear cover. Restart, cut the edge straight and reload. Don't touch the rollers, ink tubes or ink-absorbing areas.

Still stuck? Text us a photo or short video at (562) 609-4996.

Watch Epson's video: loading and removing paper on the T3770, T5770, T7770, P6570 and P8570

More videos

Epson: loading poster board
Epson: clearing paper jams

Embedded from the manufacturer's official channel.

Common questions

Do I need anything special for a 3-inch core roll?

Yes. Fit the core adapters onto both paper stops, matching the triangle marks. Take them off again for 2-inch cores.

The roll didn't feed after I pressed OK. What now?

If Auto Loading is off, or the roll doesn't feed by itself, turn the roll gently and guide the edge into the slot until you hear a sound.

What is the barcode printed on the end of my roll?

It's from Remaining Amount Management. When you reload that roll, the printer reads it and sets the paper type and length for you.

Can I feed sheets from the back?

Yes. Choose Front or Back in Paper Source Settings before you print. Either way, the sheet comes out the front.

My prints have roller marks. How do I stop them?

Turn Auto Loading off in Roll Paper Setup and feed the paper manually.

Did this fix it?