Machine type
Prestige XL series (L2, XL2, XL2 Pro, XL3, XL4)
DTF Station Prestige R2 Pro
DTF Station Prestige R1
DTF Station Prestige R2 (original)
Prestige X6
DTF Station Prestige A4
DTF Station Prestige A3+ and A3+ R
Epson SureColor G6070 DTF printer
Mimaki TxF300-1600
Mimaki TxF330-800
STS XPD-924D DTF Printer (Mutoh)
STS VJ-628D DTF Printer (Mutoh)
DTF Station Vega S17
STS XpertJet 1682D (XPJ-1682D) 64 inch DTF Printer
STS XPD-724 DTF Printer (Mutoh)
Hotronix Fusion IQ, Air Fusion IQ and Dual Air Fusion IQ
Geo Knight DK20S and DK20SP Digital Knight Swing-Away Presses
DTF Station Maxima and Proxima Dual Heat Presses
Hotronix Auto Open Clam and Hover Heat Press
DTF Station Prisma Auto Heat Press
DTF Station Prisma Dual Heat Press
DTF Station Prisma Swing Heat Press
Insta 718, 728 and 828 Automatic Swing-Away Heat Presses
DTF Station Prisma Sentry Heat Press
Geo Knight DC16 and DC16AP Digital Combo Swing-Away Presses
Geo Knight DK Digital Clamshell Presses: DK20, DK16, DKA Auto, DK8 Label and DK7 Cap
Hotronix Auto Open Cap Press and 360 IQ Hat Press
Hotronix Craft Heat Press 9 x 12
Hotronix Mighty Mug Heat Press
Insta 256 and 288 Manual Swing-Away Heat Presses
Insta 907 Dual Station Shuttle Label Heat Press
Viper MAXX pretreatment machine
Ecofreen Mister-T2 and Mister-T2 Pro pretreatment machines
Pearl Elite and Pearl PTM DTG pretreatment machines
Viper XPT-1000 pretreatment machine
Lawson Silver-Jet and Silver-Jet V2 DTG Pretreat Sprayers
Lawson Zoom-AE DTG pretreatment machine
Viper MINI handheld DTG pretreatment machine
Brand
Prestige XL series (L2, XL2, XL2 Pro, XL3, XL4)
DTF Station Prestige R2 Pro
DTF Station Prestige R1
DTF Station Prestige R2 (original)
Prestige X6
DTF Station Prestige A4
DTF Station Prestige A3+ and A3+ R
DTF Station Aries 124 UV DTF printer
Miro DTF Powder Shakers: Miro 13 Max, 16, 24 and 36
DTF Station Aries 213 and Aries 113 UV DTF printers
Seismo L16R and L24R DTF Powder Shaker and Dryer
Phoenix Air 16x20 DTF Curing Oven
DTF Station Maxima and Proxima Dual Heat Presses
DTF Station Prisma Auto Heat Press
DTF Station Prisma Dual Heat Press
DTF Station Prisma Swing Heat Press
DTF Station Vega S17
DTF Station Prisma Sentry Heat Press
DTF Station Seismo V36R DTF Powder Shaker and Dryer
DTF Station Arc 127 automatic cutter for DTF and UV DTF film
Epson SureColor F2100
Epson SureColor G6070 DTF printer
Epson SureColor F2270
Epson SureColor F3070
Epson SureColor F570
Epson SureColor F170
Epson SureColor F6470 and F6470H
Epson SureColor F6370
Epson SureColor F7200
Epson SureColor P-Series photo printers (P700, P900, P6570, P8570)
Epson SureColor T-Series CAD and technical printers
Epson SureColor S-Series (S40600, S60600, S80600)
Graphtec CE8000 blade change and cut settings: blade length, force, offset and the cut test
The CE8000 cuts with a blade inside a cutter plunger: blue ring for 0.9 mm blades (the one supplied), red ring for 1.5 mm blades. To change a blade, retract it, unscrew the plunger cap counterclockwise, swap the blade and screw the cap back on. Set the blade so it is longer than the film but shorter than film plus backing, then run CUT TEST and adjust force for depth and offset for corners.
Match your symptom
| Symptom | Likely cause | What to change |
|---|---|---|
| Rounded corners | Offset too low for the blade | Raise OFFSET |
| Over-cut corners | Offset too high | Lower OFFSET |
| Backing cut | Blade too long or force too high | Shorten the blade or lower FORCE |
| Hard to weed | Force too low, blade too short or worn | Raise FORCE a step, check length, change blade |
| Skipped lines | Blade too long or speed too high | Shorten the blade, lower SPEED |
| Crooked start | Blade not turning freely | Clean the plunger (step 2) |
| Small text lifts | Offset wrong, speed or acceleration high, dull blade | Fix offset, slow down, new blade |
| Corners curl up | Blade too long | Shorten the blade |
Cutter blades are very sharp. Don't touch the tool while the cutter is on. Never extend the blade past the thickness of the media: Graphtec warns it can damage the blade and the cutting mat.
Step by step
-
Take the plunger out
Loosen the tool holder screw until the clamp lets go, then lift the plunger out.
-
Change and clean the blade
Turn the blade-length knob to pull the blade fully into the plunger. Unscrew the plunger cap counterclockwise and take out the old blade. Clean paper dust and media powder off the blade area, because build-up dulls blades and stops them turning freely. Drop the new blade into the hole in the cap, fit the plunger back on from above and screw the cap on clockwise. The blade must go in fully and straight; if it won't, press the blade insertion port a few times and try again. Put used blades back in their case.
-
Set the blade length
Each mark on the knob moves the blade about 0.1 mm, and one full turn about 0.5 mm. Touch the tip to the media, then extend it a little at a time. The right length is more than the film's thickness but less than film plus backing. If your cutter has it, BLADE ADJUST on the home screen measures the height for you with the plunger in the rear position; treat its reading as a starting point.
-
Mount it in the right position
Push the plunger straight into the holder. For half cuts (film only) and pens, slide the clamp to the rear position; for cutting through or perforating, use the front. Tighten the screw.
-
Check the cut condition
Open the cut condition screen, choose EDIT CUT CONDITION and the condition number (1 to 8) you use for this material. Set TOOL to the blade you fitted (CB09U, CB09U-K60, CB15U, PEN or OTHER), and ASSIGN TOOL to 1 for the rear position or 3 for the front. Graphtec's Cutter Blade Manual lists starting force and offset values per blade.
-
Run the cut test
Load the actual media. Open CUT TEST, move the carriage to a clear spot with the position keys and press ENTER. To compare settings side by side, use COMPARE FORCE or COMPARE OFFSET: it cuts three patterns at the current value, one higher and one lower.
-
Read it and adjust
Peel the triangle. For a half cut, aim for faint marks on the backing only. Check the corners of the triangle and square for offset. Change one thing at a time and test again.
Graphtec's tips for easy weeding
- Use the lowest force that still leaves faint traces on the backing.
- Keep speed and acceleration low for fine detail and large sheets.
- Weed soon after cutting. Adhesive flows back into the cut lines if it sits.
- Use a sharp blade. When the plunger's tip itself wears down, replace the plunger.
Daily care
Take the tool out of the holder when you finish, lower the media set lever so the push rollers are raised, and cover the cutter. Never oil the mechanism.
Still not cutting cleanly?
Text a photo of your weeded cut test, the blade you use and your force and offset settings to (562) 609-4996.
Watch Graphtec's video: testing and adjusting blade length
Embedded from the manufacturer's official channel.
Common questions
What starting force and offset should I use?
Graphtec gives the starting values for each blade and material in its Cutter Blade Manual. On the cutter, offset is a fine adjustment around the blade's standard value, from -5 to +5. Start at 0 and let the cut test guide you.
What does a good half cut look like?
Peel the triangle from the test pattern. The film should come away cleanly and the backing should show only faint traces of the blade.
My corners are rounded. Is the blade dull?
Usually it is the offset. Graphtec says rounded corners mean the offset is too low and over-cut corners mean it is too high. A dull blade shows up more as fine lettering peeling up and media that is hard to weed.
How do I know when to change the blade?
Change it when the cut quality drops. You can also turn on the blade wear alarm, which counts cutting distance and warns you at a distance you set between 500 m and 100,000 m.
Which position in the tool holder do I use?
Rear position (tool 1) for half cuts and pens. Front position (tool 3) for cutting all the way through or perforating. Match ASSIGN TOOL in the cut condition to where the plunger sits.
- Graphtec CE8000 Series User's Manual
- Graphtec CE8000 Setup Manual
- AA support requests about Graphtec cut quality and blades, 2024 to 2026











































































