Machine type
Prestige XL series (L2, XL2, XL2 Pro, XL3, XL4)
DTF Station Prestige R2 Pro
DTF Station Prestige R1
DTF Station Prestige R2 (original)
Prestige X6
DTF Station Prestige A4
DTF Station Prestige A3+ and A3+ R
Epson SureColor G6070 DTF printer
Mimaki TxF300-1600
Mimaki TxF330-800
STS XPD-924D DTF Printer (Mutoh)
STS VJ-628D DTF Printer (Mutoh)
DTF Station Vega S17
STS XpertJet 1682D (XPJ-1682D) 64 inch DTF Printer
STS XPD-724 DTF Printer (Mutoh)
Hotronix Fusion IQ, Air Fusion IQ and Dual Air Fusion IQ
Geo Knight DK20S and DK20SP Digital Knight Swing-Away Presses
DTF Station Maxima and Proxima Dual Heat Presses
Hotronix Auto Open Clam and Hover Heat Press
DTF Station Prisma Auto Heat Press
DTF Station Prisma Dual Heat Press
DTF Station Prisma Swing Heat Press
Insta 718, 728 and 828 Automatic Swing-Away Heat Presses
DTF Station Prisma Sentry Heat Press
Geo Knight DC16 and DC16AP Digital Combo Swing-Away Presses
Geo Knight DK Digital Clamshell Presses: DK20, DK16, DKA Auto, DK8 Label and DK7 Cap
Hotronix Auto Open Cap Press and 360 IQ Hat Press
Hotronix Craft Heat Press 9 x 12
Hotronix Mighty Mug Heat Press
Insta 256 and 288 Manual Swing-Away Heat Presses
Insta 907 Dual Station Shuttle Label Heat Press
Viper MAXX pretreatment machine
Ecofreen Mister-T2 and Mister-T2 Pro pretreatment machines
Pearl Elite and Pearl PTM DTG pretreatment machines
Viper XPT-1000 pretreatment machine
Lawson Silver-Jet and Silver-Jet V2 DTG Pretreat Sprayers
Lawson Zoom-AE DTG pretreatment machine
Viper MINI handheld DTG pretreatment machine
Brand
Prestige XL series (L2, XL2, XL2 Pro, XL3, XL4)
DTF Station Prestige R2 Pro
DTF Station Prestige R1
DTF Station Prestige R2 (original)
Prestige X6
DTF Station Prestige A4
DTF Station Prestige A3+ and A3+ R
DTF Station Aries 124 UV DTF printer
Miro DTF Powder Shakers: Miro 13 Max, 16, 24 and 36
DTF Station Aries 213 and Aries 113 UV DTF printers
Seismo L16R and L24R DTF Powder Shaker and Dryer
Phoenix Air 16x20 DTF Curing Oven
DTF Station Maxima and Proxima Dual Heat Presses
DTF Station Prisma Auto Heat Press
DTF Station Prisma Dual Heat Press
DTF Station Prisma Swing Heat Press
DTF Station Vega S17
DTF Station Prisma Sentry Heat Press
DTF Station Seismo V36R DTF Powder Shaker and Dryer
DTF Station Arc 127 automatic cutter for DTF and UV DTF film
Epson SureColor F2100
Epson SureColor G6070 DTF printer
Epson SureColor F2270
Epson SureColor F3070
Epson SureColor F570
Epson SureColor F170
Epson SureColor F6470 and F6470H
Epson SureColor F6370
Epson SureColor F7200
Epson SureColor P-Series photo printers (P700, P900, P6570, P8570)
Epson SureColor T-Series CAD and technical printers
Epson SureColor S-Series (S40600, S60600, S80600)
Graphtec CE8000 or CE7000 carrier sheet not detected, fed out the back, or feeding crooked
The plotter finds a sheet's front and back edges with its media sensors, and it only looks for the back edge when you pick SHEET as the media type. Load the carrier sheet with its narrow clear margin at the top, square to the guideline and covering the media sensor, choose SHEET, and keep bright light off the sensors. Clean the sensors with a cloth and diluted neutral detergent, never alcohol, and replace a warped or worn carrier sheet.
How the plotter sees a sheet
The CE8000 and CE7000 use media sensors to find the media. When you raise the media set lever and choose the media type, SHEET detects the width, front edge and back edge. ROLL-1 FRONT EDGE detects only the width and front edge, and ROLL-2 CURRENT POSITION only the width. If the plotter does not know where the back edge is, or cannot see it, it can keep feeding until the sheet comes out the back.
Match your symptom
| What you see | Most likely cause | Go to |
|---|---|---|
| Rollers keep feeding and push the sheet out the back | Roll mode selected, sheet loaded wrong, sensor dirty or blinded by light | Steps 1 to 4 |
| "LOAD MEDIA!" with the sheet in and the lever up | Sensor cannot see the sheet | Steps 2 to 5 |
| Sheet drops or gets ejected while detecting | Bright light on the media sensor | Step 4 |
| Sheet feeds crooked, some pieces only partly cut | Sheet loaded at an angle, slipping, worn carrier sheet | Steps 2, 6 and 7 |
Step by step
-
Choose SHEET every time
After raising the media set lever, select SHEET on the media type screen (on the CE7000, the [3] key). If you raise and lower the lever again, the CE8000 offers Continue with the previous setting; only use it if nothing about the sheet changed.
-
Load it the way Graphtec shows
Lower the set lever to raise the push rollers. Insert the carrier sheet with its narrowest margin (the clear part) at the top, from the front of the plotter, with its right edge on the guideline of the front guide. Make sure it does not stick out behind the plotter and that it completely covers the media sensor. Set the push rollers on the grit rollers at both sides, pull it taut, and raise the lever.
-
Clean the media sensors
Dust or residue on a sensor causes malfunctions. Wipe the sensors with a cloth moistened with neutral detergent diluted in water. Never use alcohol, thinner, benzene or other solvents on them.
-
Keep bright light off the plotter
Graphtec lists bright light on the media sensor as a cause of dropped media and false readings. Block direct sunlight from a nearby window and move fluorescent lamps or work lights away.
-
Check the sensor setting
Make sure the media sensor has not been switched to disabled. On the CE8000 it is under the menu, CONFIG, next page, SENSOR > MEDIA SENSOR. On the CE7000 it is PAUSE/MENU, ADV., the last ADVANCE page, MEDIA SENSOR. Normal work should be ENABLED.
-
Check the carrier sheet itself
Replace it after about 10 sheets of cutting, or sooner if it is warped or has lost its tack. Graphtec does not guarantee cut quality past that. Press the media down firmly with no bubbles or creases, keep its edges parallel to the carrier sheet, and stay inside the adhesive cutting area. Use media with very little curl; curled media causes registration mark errors and can catch on the carriage. With one-side-coated inkjet media, stick the uncoated side down. Media coated on both sides cannot be used.
-
Set the start point
The plotter treats the carrier sheet's width as the cutting area. Set your page size in the software to match the media, and on the CE8000 use ORIGIN in the quick menu to set where cutting starts.
Optional: the carrier sheet table
Graphtec sells a carrier sheet table (OPH-A45) that mounts front and back to support the sheet as it moves. On the CE8000-40 it fits the first and third grooves from the right; on the CE8000-60, the second and fourth.
Still not detecting?
If the sensors are clean, the light is controlled and a new carrier sheet still is not seen, the sensor or set lever sensor may be faulty. Take a short video of the sheet loading and text it to us at (562) 609-4996.
Watch Graphtec's video: CE8000 carrier sheet table
More videos
Embedded from the manufacturer's official channel.
Common questions
It worked for months and suddenly runs the sheet out the back.
Check that SHEET is selected, clean the media sensors, and look for new bright light near the plotter, such as sun through a window or a new lamp. Graphtec lists bright light on the sensor as a cause of dropped media.
How long does a carrier sheet last?
Graphtec's guideline is to replace it after about 10 sheets of cutting. A warped sheet or one that has lost its tack must be replaced.
Can I turn the media sensor off?
Graphtec allows it for clear media the sensor cannot see, but warns that the cutting mat can be damaged and you must set the cutting area yourself. Leave it on for normal work.
Does the CE8000-130 take the carrier sheet?
No. Graphtec lists the carrier sheet for the CE8000-40 and CE8000-60 only, and the CE7000-40 and CE7000-60 on the older series.
How do I store the carrier sheet?
Put the yellow separator back on, return it to its package, and keep it away from humidity and direct sun. The adhesive absorbs moisture.
- Graphtec CE8000 Series User's Manual
- Graphtec CE7000 Series User's Manual
- Graphtec America CE8000 page
- AA support requests about Graphtec CE8000 carrier sheets, 2024 to 2026











































































