Machine type
Prestige XL series (L2, XL2, XL2 Pro, XL3, XL4)
DTF Station Prestige R2 Pro
DTF Station Prestige R1
DTF Station Prestige R2 (original)
Prestige X6
DTF Station Prestige A4
DTF Station Prestige A3+ and A3+ R
Epson SureColor G6070 DTF printer
Mimaki TxF300-1600
Mimaki TxF330-800
STS XPD-924D DTF Printer (Mutoh)
STS VJ-628D DTF Printer (Mutoh)
DTF Station Vega S17
STS XpertJet 1682D (XPJ-1682D) 64 inch DTF Printer
STS XPD-724 DTF Printer (Mutoh)
Hotronix Fusion IQ, Air Fusion IQ and Dual Air Fusion IQ
Geo Knight DK20S and DK20SP Digital Knight Swing-Away Presses
DTF Station Maxima and Proxima Dual Heat Presses
Hotronix Auto Open Clam and Hover Heat Press
DTF Station Prisma Auto Heat Press
DTF Station Prisma Dual Heat Press
DTF Station Prisma Swing Heat Press
Insta 718, 728 and 828 Automatic Swing-Away Heat Presses
DTF Station Prisma Sentry Heat Press
Geo Knight DC16 and DC16AP Digital Combo Swing-Away Presses
Geo Knight DK Digital Clamshell Presses: DK20, DK16, DKA Auto, DK8 Label and DK7 Cap
Hotronix Auto Open Cap Press and 360 IQ Hat Press
Hotronix Craft Heat Press 9 x 12
Hotronix Mighty Mug Heat Press
Insta 256 and 288 Manual Swing-Away Heat Presses
Insta 907 Dual Station Shuttle Label Heat Press
Viper MAXX pretreatment machine
Ecofreen Mister-T2 and Mister-T2 Pro pretreatment machines
Pearl Elite and Pearl PTM DTG pretreatment machines
Viper XPT-1000 pretreatment machine
Lawson Silver-Jet and Silver-Jet V2 DTG Pretreat Sprayers
Lawson Zoom-AE DTG pretreatment machine
Viper MINI handheld DTG pretreatment machine
Brand
Prestige XL series (L2, XL2, XL2 Pro, XL3, XL4)
DTF Station Prestige R2 Pro
DTF Station Prestige R1
DTF Station Prestige R2 (original)
Prestige X6
DTF Station Prestige A4
DTF Station Prestige A3+ and A3+ R
DTF Station Aries 124 UV DTF printer
Miro DTF Powder Shakers: Miro 13 Max, 16, 24 and 36
DTF Station Aries 213 and Aries 113 UV DTF printers
Seismo L16R and L24R DTF Powder Shaker and Dryer
Phoenix Air 16x20 DTF Curing Oven
DTF Station Maxima and Proxima Dual Heat Presses
DTF Station Prisma Auto Heat Press
DTF Station Prisma Dual Heat Press
DTF Station Prisma Swing Heat Press
DTF Station Vega S17
DTF Station Prisma Sentry Heat Press
DTF Station Seismo V36R DTF Powder Shaker and Dryer
DTF Station Arc 127 automatic cutter for DTF and UV DTF film
Epson SureColor F2100
Epson SureColor G6070 DTF printer
Epson SureColor F2270
Epson SureColor F3070
Epson SureColor F570
Epson SureColor F170
Epson SureColor F6470 and F6470H
Epson SureColor F6370
Epson SureColor F7200
Epson SureColor P-Series photo printers (P700, P900, P6570, P8570)
Epson SureColor T-Series CAD and technical printers
Epson SureColor S-Series (S40600, S60600, S80600)
Graphtec CE8000 and CE7000: connecting to your computer and installing Cutting Master 5 or Graphtec Studio 2
Graphtec says to install the Windows driver and your cutting software before you connect the CE8000 to the computer. Register the cutter with Graphtec America to get the download link for Cutting Master 5 (a plug-in for Illustrator and CorelDRAW) and Graphtec Studio 2 (a standalone program). Then connect by USB straight to the computer with no hub, by the optional Wi-Fi module on a 2.4 GHz network, or by wired LAN if your unit has it.
Pick your software
| Software | What it is | Runs with |
|---|---|---|
| Cutting Master 5 | A plug-in that adds cutting to your design program | Adobe Illustrator CC2016 to CC2026, CorelDRAW Graphics Suite X7 to 2025 |
| Graphtec Studio 2 | A standalone design and cut program | Opens AI, CDR, EPS, PDF, SVG and DXF files |
Both run on Windows 8.1 to 11 and macOS 10.13 to 26.1, according to Graphtec's compatibility page. Graphtec notes that a new Illustrator release can arrive before Cutting Master 5 supports it, so check that page before you update Illustrator. RIP software such as ONYX or Flexi can also drive the CE8000; set it up from that program's side.
Step by step
-
Register the cutter
Register at Graphtec America's registration page with your proof of purchase. Once you are registered, Graphtec gives you the link to download its software.
-
Install the driver and software first
Graphtec's setup manual is clear: do not connect the cutter to the computer until the Windows driver, Graphtec Studio 2 and Cutting Master 5 are installed. The Windows driver is on the CE8000 downloads page (there are separate Windows 10 32-bit and Windows 11 64-bit versions). While the driver is installing, don't plug or unplug the USB cable.
-
Connect by USB
Turn the cutter off, then connect the USB cable from the USB interface connector on the back to the computer. Plug it straight into the computer: Graphtec does not guarantee operation through a USB hub or extension port, or with a driver other than the CE8000 one. Don't unplug the cable while the cutter or computer is starting up, or within 5 seconds of plugging it in.
-
Or connect by Wi-Fi
Wi-Fi needs the optional wireless LAN module. With the power off, remove the module cap on the back, push the module in with its hole facing down until it is fully seated, and screw the cover on with your own Phillips screwdriver. The first time the cutter starts it asks for language, units and whether to set up wireless LAN. Follow the screens: pick your network, enter the password and connect.
When the cutter shows its default static IP address, turn DHCP on and press OK. Graphtec marks this step as very important. The cutter restarts and shows a wireless icon at the top right when it is on the network.
-
Or connect by wired LAN
Wired LAN is a factory-installed option. If your unit has it, connect a standard network cable and set the IP address or DHCP in the cutter's network settings (chapter 9 of the user's manual).
-
Select the cutter in your software and test
Choose the CE8000 in Cutting Master 5 or Graphtec Studio 2 and send a small job. The cutter switches between USB, Wi-Fi and LAN on its own and cuts the first job it receives.
When the software can't reach the cutter
Graphtec's own troubleshooting order, for messages like "not responding" or jobs that never arrive:
- Cable: Graphtec's print and cut guide says to keep the USB cable under 15 feet with no hubs or adapters, and to try a new cable.
- Network: if you use Wi-Fi or LAN, try USB. If USB works, the problem is on the network side; ask whoever manages your network.
- Command type: the cutter understands GP-GL and HP-GL. Match it to your software, or set it to AUTO, under the menu: CONFIG > COMMAND > COMMAND TYPE.
- Command errors on the screen (codes starting E02 or E03): Graphtec says these nearly always mean the software's output device setting or the cutter's interface setting changed. Select the cutter again in the software.
- Third-party software: try the same job from Graphtec's software. If that works, contact the maker of the other program and tell them the cutter works with Graphtec's software.
Need a hand?
Text a photo of the error and tell us your computer's operating system and which software you use. We're at (562) 609-4996.
Watch Graphtec's video: installing the CE8000 Wi-Fi module
More videos
Embedded from the manufacturer's official channel.
Common questions
Do I have to pay for Cutting Master 5 or Graphtec Studio 2?
Graphtec America provides both as downloads once you register the cutter. Registration asks for proof of purchase.
Which one should I use?
Use Cutting Master 5 if you design in Adobe Illustrator or CorelDRAW Graphics Suite, because it adds a cut command inside those programs. Use Graphtec Studio 2 if you want a standalone program; it opens AI, CDR, EPS, PDF, SVG and DXF files.
My CorelDRAW is the Home or Standard edition. Will Cutting Master 5 work?
No. Graphtec lists only CorelDRAW Graphics Suite as compatible. Home, Student, Standard, Essentials and Technical Suite editions are not. Use Graphtec Studio 2 instead.
My software says the cutter is not responding. What do I check?
The software is not getting an answer from the cutter. Plug the USB cable straight into the computer with no hub or adapter, try a different cable, set the cutter's command type to AUTO or to what your software uses, then try cutting from Graphtec's own software. If Graphtec's software works, the problem is in the other program.
The cutter can't find my Wi-Fi network.
The CE8000 only supports 2.4 GHz networks (802.11b/g/n). It will not see a 5 GHz network.
Can I run the CE7000 with the same software?
Yes. Graphtec lists the CE7000 as fully supported by both Cutting Master 5 and Graphtec Studio 2. Its menus are on keys rather than a touch screen, so follow the CE7000 manual for the cutter-side settings.
- Graphtec CE8000 Setup Manual
- Graphtec CE8000 Series User's Manual
- Graphtec America CE8000 page: downloads, driver and firmware
- Graphtec America software compatibility (Cutting Master 5 and Graphtec Studio 2)
- Graphtec America product registration
- Graphtec CE8000 Wireless LAN Setup
- Graphtec: Print and Cut Issues and Solutions for the CE7000 Series
- AA support requests about Graphtec software, activation and connection, 2024 to 2026











































































