Machine type
Prestige XL series (L2, XL2, XL2 Pro, XL3, XL4)
DTF Station Prestige R2 Pro
DTF Station Prestige R1
DTF Station Prestige R2 (original)
Prestige X6
DTF Station Prestige A4
DTF Station Prestige A3+ and A3+ R
Epson SureColor G6070 DTF printer
Mimaki TxF300-1600
Mimaki TxF330-800
STS XPD-924D DTF Printer (Mutoh)
STS VJ-628D DTF Printer (Mutoh)
DTF Station Vega S17
STS XpertJet 1682D (XPJ-1682D) 64 inch DTF Printer
STS XPD-724 DTF Printer (Mutoh)
Hotronix Fusion IQ, Air Fusion IQ and Dual Air Fusion IQ
Geo Knight DK20S and DK20SP Digital Knight Swing-Away Presses
DTF Station Maxima and Proxima Dual Heat Presses
Hotronix Auto Open Clam and Hover Heat Press
DTF Station Prisma Auto Heat Press
DTF Station Prisma Dual Heat Press
DTF Station Prisma Swing Heat Press
Insta 718, 728 and 828 Automatic Swing-Away Heat Presses
DTF Station Prisma Sentry Heat Press
Geo Knight DC16 and DC16AP Digital Combo Swing-Away Presses
Geo Knight DK Digital Clamshell Presses: DK20, DK16, DKA Auto, DK8 Label and DK7 Cap
Hotronix Auto Open Cap Press and 360 IQ Hat Press
Hotronix Craft Heat Press 9 x 12
Hotronix Mighty Mug Heat Press
Insta 256 and 288 Manual Swing-Away Heat Presses
Insta 907 Dual Station Shuttle Label Heat Press
Viper MAXX pretreatment machine
Ecofreen Mister-T2 and Mister-T2 Pro pretreatment machines
Pearl Elite and Pearl PTM DTG pretreatment machines
Viper XPT-1000 pretreatment machine
Lawson Silver-Jet and Silver-Jet V2 DTG Pretreat Sprayers
Lawson Zoom-AE DTG pretreatment machine
Viper MINI handheld DTG pretreatment machine
Brand
Prestige XL series (L2, XL2, XL2 Pro, XL3, XL4)
DTF Station Prestige R2 Pro
DTF Station Prestige R1
DTF Station Prestige R2 (original)
Prestige X6
DTF Station Prestige A4
DTF Station Prestige A3+ and A3+ R
DTF Station Aries 124 UV DTF printer
Miro DTF Powder Shakers: Miro 13 Max, 16, 24 and 36
DTF Station Aries 213 and Aries 113 UV DTF printers
Seismo L16R and L24R DTF Powder Shaker and Dryer
Phoenix Air 16x20 DTF Curing Oven
DTF Station Maxima and Proxima Dual Heat Presses
DTF Station Prisma Auto Heat Press
DTF Station Prisma Dual Heat Press
DTF Station Prisma Swing Heat Press
DTF Station Vega S17
DTF Station Prisma Sentry Heat Press
DTF Station Seismo V36R DTF Powder Shaker and Dryer
DTF Station Arc 127 automatic cutter for DTF and UV DTF film
Epson SureColor F2100
Epson SureColor G6070 DTF printer
Epson SureColor F2270
Epson SureColor F3070
Epson SureColor F570
Epson SureColor F170
Epson SureColor F6470 and F6470H
Epson SureColor F6370
Epson SureColor F7200
Epson SureColor P-Series photo printers (P700, P900, P6570, P8570)
Epson SureColor T-Series CAD and technical printers
Epson SureColor S-Series (S40600, S60600, S80600)
Graphtec CE8000 error messages and POSITION ALARM: what they mean and what to do
CE8000 error codes are grouped by their first digits: E01 is the machine itself, E02 and E03 are data from the computer, E04 is registration marks, E05 is copy, USB and data link functions, and E07 is Wi-Fi. POSITION ALARM means the carriage was blocked or the cut condition is too aggressive: clear anything in its path, power off and on, and lower speed or force. Codes E01001 to E01015 mean a fault Graphtec says needs service.
First, read the error log
If a message flashed by, open the menu, press INFO, go to the next page and press ERROR MESSAGES. The cutter lists up to 32 recent errors; tap one to see its details. Write the code down before you contact us.
Error codes
| Code | Meaning | What to do |
|---|---|---|
| E01001 to E01015 | Plotter fault | Contact us with the code |
| E01017, E01019, E01021 | Motor overloaded | Clear anything blocking it, power off and on, don't use heavy media |
| E01022 | Tool up and down blocked | Clear the tool carriage, power off and on |
| E01029 | Wi-Fi module error | Power off and on |
| E02001 to E02005 | Data from the computer not understood | Select the cutter again in your software; check the cutter's interface settings |
| E02006 | Data outside the cutting area | Check media size, cutting area, scaling and step size |
| E03001 to E03014 | HP-GL command errors | Same as E02: reselect the cutter in the software |
| E04001 to E04025 | Registration mark problems | See our CE8000 print and cut guide |
| E05004 | Push roller off the grit roller | Move it onto a grit roller |
| E05008, E05012 | USB stick not seen, or file missing | Reinsert the USB memory, check the file is on it |
| E05014 | Connection destination not found | Connect it by USB or LAN cable |
| E05017 | Media set lever lowered | Load the media again |
| E05022 | Media skew detected | Reload the media straight |
| E07001 to E07005 | Wi-Fi access point problem | Check the router is on and nearby, and the password is right |
The E05 codes not listed here relate to copy mode, barcodes and data link. Graphtec's manual lists each one in section 15.1.
POSITION ALARM
Graphtec lists these causes, in order of what to check:
-
Something blocked the carriage
An object in its path, a hand on the carriage, or media scraps built up in the working area. Remove it, then switch the cutter off and on.
-
The cut condition is too much for the media
If it stops during initializing or cutting, lower the speed or the force for that condition number.
-
It hits the side right after you choose the media type
Hitting the left side points to the push roller sensor; hitting the right side points to the home sensor. Contact us. Graphtec allows the push roller sensor to be disabled as a temporary workaround, but have us confirm first.
Keep hands, hair and loose clothing away from the carriage and rollers whenever the cutter is on. It can move suddenly during setup as well as during cutting.
Other messages and behaviors
| What you see | Cause | Fix |
|---|---|---|
| Media shoots out the front | Wrong media type chosen | Pick SHEET, ROLL-1 or ROLL-2 to match what you loaded |
| LOAD MEDIA! with media in | Clear media, or strong light on the sensor | Move lights, block sun; see our carrier sheet guide |
| Stops cutting partway | Job longer than the page length set on the cutter | Press SLOW to show the cutting area, then match the page length |
| Settings keep changing | Command priority is set | Set priority to MENU PRIORITY |
| Wi-Fi network not listed | 5 GHz network | Use a 2.4 GHz network |
| Cut starts from the center | Origin set differently on cutter and software | Match the origin point in both |
Need a hand?
Text the code, a photo of the screen and what the cutter was doing to (562) 609-4996.
Common questions
Where can I see errors I missed?
Open the menu, then INFO, go to the next page and press ERROR MESSAGES. The cutter keeps the last 32 errors with how long ago each happened.
The screen shows POSITION ALARM in the middle of a job.
Something stopped the carriage or the media: an object, your hand, or a build-up of media scraps. It also happens when speed or force is set too high for the media. Clear the path, switch off and on, and lower speed or force.
The touch screen doesn't respond.
It is a capacitive screen. Use your finger or a capacitive stylus; pressure-type stylus pens do not work.
I get E05004.
A push roller is not sitting on a grit roller. Move it onto one, using the grit roller guide marks on the front rail.
The display is blank when I switch it on.
Check the power cord at both ends and that the outlet has power. If it is still blank, or shows Sum-Ck ROM RAM ERR, contact us.
- Graphtec CE8000 Series User's Manual
- Graphtec America tech support
- AA support requests about Graphtec CE7000 and CE8000 errors, 2024 to 2026











































































